
#include <osl.h>
#include <dhd_linux.h>
#include <linux/gpio.h>

#if defined(BUS_POWER_RESTORE) && defined(BCMSDIO)
#include <linux/mmc/core.h>
#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sdio_func.h>
#endif /* defined(BUS_POWER_RESTORE) && defined(BCMSDIO) */

#ifdef CONFIG_DHD_USE_STATIC_BUF
#ifdef DHD_STATIC_IN_DRIVER
extern int dhd_static_buf_init(void);
extern void dhd_static_buf_exit(void);
#endif /* DHD_STATIC_IN_DRIVER */
#ifdef BCMDHD_MDRIVER
extern void *bcmdhd_mem_prealloc(uint bus_type, int index,
	int section, unsigned long size);
#else
extern void *bcmdhd_mem_prealloc(int section, unsigned long size);
#endif
#endif /* CONFIG_DHD_USE_STATIC_BUF */

#ifdef BCMDHD_DTS
/* This is sample code in dts file.
bcmdhd {
	compatible = "android,bcmdhd_wlan";
	gpio_wl_reg_on = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
	gpio_wl_host_wake = <&gpio GPIOZ_15 GPIO_ACTIVE_HIGH>;
};
*/
#define DHD_DT_COMPAT_ENTRY		"android,bcmdhd_wlan"
#define GPIO_WL_REG_ON_PROPNAME		"gpio_wl_reg_on"
#define GPIO_WL_HOST_WAKE_PROPNAME	"gpio_wl_host_wake"
#endif

#ifdef CUSTOMER_HW_AMLOGIC
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(4, 8, 0))
#include <linux/amlogic/aml_gpio_consumer.h>
extern int wifi_irq_trigger_level(void);
extern u8 *wifi_get_mac(void);
extern u8 *wifi_get_ap_mac(void);
#endif
extern void sdio_reinit(void);
extern void set_usb_bt_power(int is_power);
extern void set_usb_wifi_power(int is_power);
extern void extern_wifi_set_enable(int is_on);
extern void pci_remove_reinit(unsigned int vid, unsigned int pid, int delBus);
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(3, 14, 0))
extern int wifi_irq_num(void);
#endif
int dhd_pwr_ctrl = 1;
module_param(dhd_pwr_ctrl, int, 0);
#endif

static int
dhd_wlan_set_power(int on, wifi_adapter_info_t *adapter)
{
	int gpio_wl_reg_on = adapter->gpio_wl_reg_on;
	int err = 0;

#ifdef CUSTOMER_HW_AMLOGIC
    printf("######### dhd_pwr_ctrl=%d #########\n", dhd_pwr_ctrl);
#endif

	if (on) {
		printf("======== PULL WL_REG_ON(%d) HIGH! ========\n", gpio_wl_reg_on);
		if (gpio_wl_reg_on >= 0) {
			err = gpio_direction_output(gpio_wl_reg_on, 1);
			if (err) {
				printf("%s: WL_REG_ON didn't output high\n", __FUNCTION__);
				return -EIO;
			}
		}
#ifdef CUSTOMER_HW_AMLOGIC
#ifdef BCMSDIO
		extern_wifi_set_enable(0);
		mdelay(200);
		extern_wifi_set_enable(1);
		mdelay(200);
//		sdio_reinit();
#endif
#ifdef BCMDBUS
    if (dhd_pwr_ctrl) {
		set_usb_wifi_power(0);
		mdelay(200);
		set_usb_wifi_power(1);
		mdelay(200);
    }
#endif
#endif
#ifdef BUS_POWER_RESTORE
#ifdef BCMSDIO
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 32) && LINUX_VERSION_CODE < KERNEL_VERSION(4, 19, 0)
		if (adapter->sdio_func && adapter->sdio_func->card && adapter->sdio_func->card->host) {
			mdelay(100);
			printf("======== mmc_power_restore_host! ========\n");
			mmc_power_restore_host(adapter->sdio_func->card->host);
		}
#endif
#elif defined(BCMPCIE)
		if (adapter->pci_dev) {
			mdelay(100);
			printf("======== pci_set_power_state PCI_D0! ========\n");
			pci_set_power_state(adapter->pci_dev, PCI_D0);
			if (adapter->pci_saved_state)
				pci_load_and_free_saved_state(adapter->pci_dev, &adapter->pci_saved_state);
			pci_restore_state(adapter->pci_dev);
			err = pci_enable_device(adapter->pci_dev);
			if (err < 0)
				printf("%s: PCI enable device failed", __FUNCTION__);
			pci_set_master(adapter->pci_dev);
		}
#endif /* BCMPCIE */
#endif /* BUS_POWER_RESTORE */
		/* Lets customer power to get stable */
		mdelay(100);
	} else {
#ifdef BUS_POWER_RESTORE
#ifdef BCMSDIO
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2, 6, 32) && LINUX_VERSION_CODE < KERNEL_VERSION(4, 19, 0)
		if (adapter->sdio_func && adapter->sdio_func->card && adapter->sdio_func->card->host) {
			printf("======== mmc_power_save_host! ========\n");
			mmc_power_save_host(adapter->sdio_func->card->host);
		}
#endif
#elif defined(BCMPCIE)
		if (adapter->pci_dev) {
			printf("======== pci_set_power_state PCI_D3hot! ========\n");
			pci_save_state(adapter->pci_dev);
			adapter->pci_saved_state = pci_store_saved_state(adapter->pci_dev);
			if (pci_is_enabled(adapter->pci_dev))
				pci_disable_device(adapter->pci_dev);
			pci_set_power_state(adapter->pci_dev, PCI_D3hot);
		}
#endif /* BCMPCIE */
#endif /* BUS_POWER_RESTORE */
		printf("======== PULL WL_REG_ON(%d) LOW! ========\n", gpio_wl_reg_on);
		if (gpio_wl_reg_on >= 0) {
			err = gpio_direction_output(gpio_wl_reg_on, 0);
			if (err) {
				printf("%s: WL_REG_ON didn't output low\n", __FUNCTION__);
				return -EIO;
			}
		}
#ifdef CUSTOMER_HW_AMLOGIC
#ifdef BCMSDIO
		extern_wifi_set_enable(0);
		mdelay(200);
#endif
#ifdef BCMDBUS
    if (dhd_pwr_ctrl) {
		set_usb_wifi_power(0);
		mdelay(200);
    }
#endif
#endif
	}

	return err;
}

static int dhd_wlan_set_reset(int onoff)
{
	return 0;
}

static int dhd_wlan_set_carddetect(int present)
{
	int err = 0;

#if !defined(BUS_POWER_RESTORE)
	if (present) {
#if defined(BCMSDIO)
		printf("======== Card detection to detect SDIO card! ========\n");
#ifdef CUSTOMER_HW_PLATFORM
		err = sdhci_force_presence_change(&sdmmc_channel, 1);
#endif /* CUSTOMER_HW_PLATFORM */
#ifdef CUSTOMER_HW_AMLOGIC
		sdio_reinit();
#endif
#elif defined(BCMPCIE)
		printf("======== Card detection to detect PCIE card! ========\n");
#endif
	} else {
#if defined(BCMSDIO)
		printf("======== Card detection to remove SDIO card! ========\n");
#ifdef CUSTOMER_HW_PLATFORM
		err = sdhci_force_presence_change(&sdmmc_channel, 0);
#endif /* CUSTOMER_HW_PLATFORM */
#ifdef CUSTOMER_HW_AMLOGIC
		extern_wifi_set_enable(0);
		mdelay(200);
#endif
#elif defined(BCMPCIE)
		printf("======== Card detection to remove PCIE card! ========\n");
#ifdef CUSTOMER_HW_AMLOGIC
		//extern_wifi_set_enable(0);
		//mdelay(200);
#endif
#endif
	}
#endif /* BUS_POWER_RESTORE */

	return err;
}

static int dhd_wlan_get_mac_addr(unsigned char *buf, int ifidx)
{
	int err = 0;

	if (ifidx == 1) {
#ifdef EXAMPLE_GET_MAC
		struct ether_addr ea_example = {{0x00, 0x11, 0x22, 0x33, 0x44, 0xFF}};
		bcopy((char *)&ea_example, buf, sizeof(struct ether_addr));
#endif /* EXAMPLE_GET_MAC */
#ifdef CUSTOMER_HW_AMLOGIC
#ifdef CUSTOM_AP_MAC
		bcopy((char *)wifi_get_ap_mac(), buf, sizeof(struct ether_addr));
		if (buf[0] == 0xff) {
			printf("custom wifi ap mac is not set\n");
			err = -1;
		} else
			printf("custom wifi ap mac-addr: %02x:%02x:%02x:%02x:%02x:%02x\n",
				buf[0], buf[1], buf[2],
				buf[3], buf[4], buf[5]);
#else
		err = -1;
#endif
#endif
	} else {
#ifdef EXAMPLE_GET_MAC
		struct ether_addr ea_example = {{0x02, 0x11, 0x22, 0x33, 0x44, 0x55}};
		bcopy((char *)&ea_example, buf, sizeof(struct ether_addr));
#endif /* EXAMPLE_GET_MAC */
#ifdef CUSTOMER_HW_AMLOGIC
		bcopy((char *)wifi_get_mac(), buf, sizeof(struct ether_addr));
		if (buf[0] == 0xff) {
			printf("custom wifi mac is not set\n");
			err = -1;
		} else
			printf("custom wifi mac-addr: %02x:%02x:%02x:%02x:%02x:%02x\n",
				buf[0], buf[1], buf[2],
				buf[3], buf[4], buf[5]);
#endif
	}

#ifdef EXAMPLE_GET_MAC_VER2
	/* EXAMPLE code */
	{
		char macpad[56]= {
		0x00,0xaa,0x9c,0x84,0xc7,0xbc,0x9b,0xf6,
		0x02,0x33,0xa9,0x4d,0x5c,0xb4,0x0a,0x5d,
		0xa8,0xef,0xb0,0xcf,0x8e,0xbf,0x24,0x8a,
		0x87,0x0f,0x6f,0x0d,0xeb,0x83,0x6a,0x70,
		0x4a,0xeb,0xf6,0xe6,0x3c,0xe7,0x5f,0xfc,
		0x0e,0xa7,0xb3,0x0f,0x00,0xe4,0x4a,0xaf,
		0x87,0x08,0x16,0x6d,0x3a,0xe3,0xc7,0x80};
		bcopy(macpad, buf+6, sizeof(macpad));
	}
#endif /* EXAMPLE_GET_MAC_VER2 */

	printf("======== %s err=%d ========\n", __FUNCTION__, err);

	return err;
}

static struct cntry_locales_custom brcm_wlan_translate_custom_table[] = {
	/* Table should be filled out based on custom platform regulatory requirement */
#ifdef EXAMPLE_TABLE
	{"",   "XT", 49},  /* Universal if Country code is unknown or empty */
	{"US", "US", 0},
#endif /* EXMAPLE_TABLE */
};

#ifdef CUSTOM_FORCE_NODFS_FLAG
struct cntry_locales_custom brcm_wlan_translate_nodfs_table[] = {
#ifdef EXAMPLE_TABLE
	{"",   "XT", 50},  /* Universal if Country code is unknown or empty */
	{"US", "US", 0},
#endif /* EXMAPLE_TABLE */
};
#endif

static void *dhd_wlan_get_country_code(char *ccode
#ifdef CUSTOM_FORCE_NODFS_FLAG
	, u32 flags
#endif
)
{
	struct cntry_locales_custom *locales;
	int size;
	int i;

	if (!ccode)
		return NULL;

#ifdef CUSTOM_FORCE_NODFS_FLAG
	if (flags & WLAN_PLAT_NODFS_FLAG) {
		locales = brcm_wlan_translate_nodfs_table;
		size = ARRAY_SIZE(brcm_wlan_translate_nodfs_table);
	} else {
#endif
		locales = brcm_wlan_translate_custom_table;
		size = ARRAY_SIZE(brcm_wlan_translate_custom_table);
#ifdef CUSTOM_FORCE_NODFS_FLAG
	}
#endif

	for (i = 0; i < size; i++)
		if (strcmp(ccode, locales[i].iso_abbrev) == 0)
			return &locales[i];
	return NULL;
}

struct wifi_platform_data dhd_wlan_control = {
	.set_power	= dhd_wlan_set_power,
	.set_reset	= dhd_wlan_set_reset,
	.set_carddetect	= dhd_wlan_set_carddetect,
	.get_mac_addr	= dhd_wlan_get_mac_addr,
#ifdef CONFIG_DHD_USE_STATIC_BUF
	.mem_prealloc	= bcmdhd_mem_prealloc,
#endif /* CONFIG_DHD_USE_STATIC_BUF */
	.get_country_code = dhd_wlan_get_country_code,
};

int dhd_wlan_init_gpio(wifi_adapter_info_t *adapter)
{
#ifdef BCMDHD_DTS
	char wlan_node[32];
	struct device_node *root_node = NULL;
#endif
	int err = 0;
	int gpio_wl_reg_on;
#ifdef CUSTOMER_OOB
	int gpio_wl_host_wake;
	int host_oob_irq = -1;
	uint host_oob_irq_flags = 0;
#endif

	/* Please check your schematic and fill right GPIO number which connected to
	* WL_REG_ON and WL_HOST_WAKE.
	*/
#ifdef BCMDHD_DTS
	strcpy(wlan_node, DHD_DT_COMPAT_ENTRY);
	printf("======== Get GPIO from DTS(%s) ========\n", wlan_node);
	root_node = of_find_compatible_node(NULL, NULL, wlan_node);
	if (root_node) {
		gpio_wl_reg_on = of_get_named_gpio(root_node, GPIO_WL_REG_ON_PROPNAME, 0);
#ifdef CUSTOMER_OOB
		gpio_wl_host_wake = of_get_named_gpio(root_node, GPIO_WL_HOST_WAKE_PROPNAME, 0);
#endif
	} else
#endif
	{
		gpio_wl_reg_on = -1;
#ifdef CUSTOMER_OOB
		gpio_wl_host_wake = -1;
#endif
	}

#ifdef CUSTOMER_HW_AMLOGIC
#if defined(BCMPCIE)
	printf("======== Card detection to detect PCIE card! ========\n");
//	pci_remove_reinit(0x14e4, 0x43ec, 1);
#endif
#endif

	if (gpio_wl_reg_on >= 0) {
		err = gpio_request(gpio_wl_reg_on, "WL_REG_ON");
		if (err < 0) {
			printf("%s: gpio_request(%d) for WL_REG_ON failed\n",
				__FUNCTION__, gpio_wl_reg_on);
			gpio_wl_reg_on = -1;
		}
	}
	adapter->gpio_wl_reg_on = gpio_wl_reg_on;

#ifdef CUSTOMER_OOB
	if (gpio_wl_host_wake >= 0) {
		err = gpio_request(gpio_wl_host_wake, "bcmdhd");
		if (err < 0) {
			printf("%s: gpio_request(%d) for WL_HOST_WAKE failed\n",
				__FUNCTION__, gpio_wl_host_wake);
			return -1;
		}
		adapter->gpio_wl_host_wake = gpio_wl_host_wake;
		err = gpio_direction_input(gpio_wl_host_wake);
		if (err < 0) {
			printf("%s: gpio_direction_input(%d) for WL_HOST_WAKE failed\n",
				__FUNCTION__, gpio_wl_host_wake);
			gpio_free(gpio_wl_host_wake);
			return -1;
		}
		host_oob_irq = gpio_to_irq(gpio_wl_host_wake);
		if (host_oob_irq < 0) {
			printf("%s: gpio_to_irq(%d) for WL_HOST_WAKE failed\n",
				__FUNCTION__, gpio_wl_host_wake);
			gpio_free(gpio_wl_host_wake);
			return -1;
		}
	}
#ifdef CUSTOMER_HW_AMLOGIC
#if (LINUX_VERSION_CODE < KERNEL_VERSION(3, 14, 0))
	host_oob_irq = INT_GPIO_4;
#else
	host_oob_irq = wifi_irq_num();
#endif
#endif

#ifdef HW_OOB
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(4, 8, 0))
	if (wifi_irq_trigger_level() == GPIO_IRQ_LOW)
		host_oob_irq_flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL | IORESOURCE_IRQ_SHAREABLE;
	else
		host_oob_irq_flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL | IORESOURCE_IRQ_SHAREABLE;
#else
#ifdef HW_OOB_LOW_LEVEL
	host_oob_irq_flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL | IORESOURCE_IRQ_SHAREABLE;
#else
	host_oob_irq_flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL | IORESOURCE_IRQ_SHAREABLE;
#endif
#endif
#else
	host_oob_irq_flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_SHAREABLE;
#endif
	host_oob_irq_flags &= IRQF_TRIGGER_MASK;

	adapter->irq_num = host_oob_irq;
	adapter->intr_flags = host_oob_irq_flags;
	printf("%s: WL_HOST_WAKE=%d, oob_irq=%d, oob_irq_flags=0x%x\n", __FUNCTION__,
		gpio_wl_host_wake, host_oob_irq, host_oob_irq_flags);
#endif /* CUSTOMER_OOB */
	printf("%s: WL_REG_ON=%d\n", __FUNCTION__, gpio_wl_reg_on);

	return 0;
}

static void dhd_wlan_deinit_gpio(wifi_adapter_info_t *adapter)
{
	int gpio_wl_reg_on = adapter->gpio_wl_reg_on;
#ifdef CUSTOMER_OOB
	int gpio_wl_host_wake = adapter->gpio_wl_host_wake;
#endif

	if (gpio_wl_reg_on >= 0) {
		printf("%s: gpio_free(WL_REG_ON %d)\n", __FUNCTION__, gpio_wl_reg_on);
		gpio_free(gpio_wl_reg_on);
		gpio_wl_reg_on = -1;
	}
#ifdef CUSTOMER_OOB
	if (gpio_wl_host_wake >= 0) {
		printf("%s: gpio_free(WL_HOST_WAKE %d)\n", __FUNCTION__, gpio_wl_host_wake);
		gpio_free(gpio_wl_host_wake);
		gpio_wl_host_wake = -1;
	}
#endif /* CUSTOMER_OOB */
}

int dhd_wlan_init_plat_data(wifi_adapter_info_t *adapter)
{
	int err = 0;

	printf("======== %s ========\n", __FUNCTION__);
	if (adapter->index == -1) {
		adapter->index = 0;
	}
	err = dhd_wlan_init_gpio(adapter);

#ifdef DHD_STATIC_IN_DRIVER
	dhd_static_buf_init();
#endif
	return err;
}

void dhd_wlan_deinit_plat_data(wifi_adapter_info_t *adapter)
{
	printf("======== %s ========\n", __FUNCTION__);
#ifdef DHD_STATIC_IN_DRIVER
	dhd_static_buf_exit();
#endif
	dhd_wlan_deinit_gpio(adapter);
}