blob: 2da316e04409f103c44fcf4ff35fe5dc48a93924 [file] [log] [blame]
/*
* Copyright 2012 Freescale Semiconductor, Inc.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
/include/ "imx28.dtsi"
/ {
model = "Freescale i.MX28 Evaluation Kit";
compatible = "fsl,imx28-evk", "fsl,imx28";
memory {
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
gpmi-nand@8000c000 {
pinctrl-names = "default";
pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
&gpmi_pins_evk>;
status = "okay";
};
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_8bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
wp-gpios = <&gpio2 12 0>;
vmmc-supply = <&reg_vddio_sd0>;
status = "okay";
};
ssp1: ssp@80012000 {
compatible = "fsl,imx28-mmc";
bus-width = <8>;
wp-gpios = <&gpio0 28 0>;
};
ssp2: ssp@80014000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx28-spi";
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
flash: m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "sst,sst25vf016b";
spi-max-frequency = <40000000>;
reg = <0>;
};
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */
0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */
0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */
0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
led_pin_gpio3_5: led_gpio3_5@0 {
reg = <0>;
fsl,pinmux-ids = <
0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
gpmi_pins_evk: gpmi-nand-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */
0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
lcdif_pins_evk: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_evk>;
panel-enable-gpios = <&gpio3 30 0>;
status = "okay";
};
can0: can@80032000 {
pinctrl-names = "default";
pinctrl-0 = <&can0_pins_a>;
status = "okay";
};
can1: can@80034000 {
pinctrl-names = "default";
pinctrl-0 = <&can1_pins_a>;
status = "okay";
};
};
apbx@80040000 {
saif0: saif@80042000 {
pinctrl-names = "default";
pinctrl-0 = <&saif0_pins_a>;
status = "okay";
};
saif1: saif@80046000 {
pinctrl-names = "default";
pinctrl-0 = <&saif1_pins_a>;
fsl,saif-master = <&saif0>;
status = "okay";
};
lradc@80050000 {
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
VDDA-supply = <&reg_3p3v>;
VDDIO-supply = <&reg_3p3v>;
};
at24@51 {
compatible = "at24,24c32";
pagesize = <32>;
reg = <0x51>;
};
};
pwm: pwm@80064000 {
pinctrl-names = "default";
pinctrl-0 = <&pwm2_pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_pins_a>;
status = "okay";
};
auart3: serial@80070000 {
pinctrl-names = "default";
pinctrl-0 = <&auart3_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
usbphy1: usbphy@8007e000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
vbus-supply = <&reg_usb0_vbus>;
status = "okay";
};
usb1: usb@80090000 {
vbus-supply = <&reg_usb1_vbus>;
status = "okay";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
phy-supply = <&reg_fec_3v3>;
phy-reset-gpios = <&gpio4 13 0>;
phy-reset-duration = <100>;
status = "okay";
};
mac1: ethernet@800f4000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac1_pins_a>;
status = "okay";
};
};
regulators {
compatible = "simple-bus";
reg_3p3v: 3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_vddio_sd0: vddio-sd0 {
compatible = "regulator-fixed";
regulator-name = "vddio-sd0";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio3 28 0>;
};
reg_fec_3v3: fec-3v3 {
compatible = "regulator-fixed";
regulator-name = "fec-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio2 15 0>;
};
reg_usb0_vbus: usb0_vbus {
compatible = "regulator-fixed";
regulator-name = "usb0_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 9 0>;
enable-active-high;
};
reg_usb1_vbus: usb1_vbus {
compatible = "regulator-fixed";
regulator-name = "usb1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 8 0>;
enable-active-high;
};
};
sound {
compatible = "fsl,imx28-evk-sgtl5000",
"fsl,mxs-audio-sgtl5000";
model = "imx28-evk-sgtl5000";
saif-controllers = <&saif0 &saif1>;
audio-codec = <&sgtl5000>;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pin_gpio3_5>;
user {
label = "Heartbeat";
gpios = <&gpio3 5 0>;
linux,default-trigger = "heartbeat";
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 2 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
};
};