| /* |
| * Copyright (c) 2012, 2015, 2017-2018, The Linux Foundation. All rights reserved. |
| * Permission to use, copy, modify, and/or distribute this software for |
| * any purpose with or without fee is hereby granted, provided that the |
| * above copyright notice and this permission notice appear in all copies. |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT |
| * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| |
| |
| #ifndef _F1_PHY_H_ |
| #define _F1_PHY_H_ |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif /* __cplusplus */ |
| |
| /* PHY Registers */ |
| #define F1_PHY_CONTROL 0 |
| #define F1_PHY_STATUS 1 |
| #define F1_PHY_ID1 2 |
| #define F1_PHY_ID2 3 |
| #define F1_AUTONEG_ADVERT 4 |
| #define F1_LINK_PARTNER_ABILITY 5 |
| #define F1_AUTONEG_EXPANSION 6 |
| #define F1_NEXT_PAGE_TRANSMIT 7 |
| #define F1_LINK_PARTNER_NEXT_PAGE 8 |
| #define F1_1000BASET_CONTROL 9 |
| #define F1_1000BASET_STATUS 10 |
| #define F1_MMD_CTRL_REG 13 |
| #define F1_MMD_DATA_REG 14 |
| #define F1_EXTENDED_STATUS 15 |
| #define F1_PHY_SPEC_CONTROL 16 |
| #define F1_PHY_SPEC_STATUS 17 |
| #define F1_PHY_INTR_MASK 18 |
| #define F1_PHY_INTR_STATUS 19 |
| #define F1_PHY_CDT_CONTROL 22 |
| #define F1_PHY_CDT_STATUS 28 |
| #define F1_DEBUG_PORT_ADDRESS 29 |
| #define F1_DEBUG_PORT_DATA 30 |
| #define F1_PHY_8023AZ_EEE_CTRL 0x3c |
| #define F1_PHY_MMD7_NUM 7 |
| #define F1_PHY_AZ_ENABLE 0x6 |
| |
| /*debug port*/ |
| #define F1_DEBUG_PORT_RGMII_MODE 18 |
| #define F1_DEBUG_PORT_RGMII_MODE_EN 0x0008 |
| |
| #define F1_DEBUG_PORT_RX_DELAY 0 |
| #define F1_DEBUG_PORT_RX_DELAY_EN 0x8000 |
| |
| #define F1_DEBUG_PORT_TX_DELAY 5 |
| #define F1_DEBUG_PORT_TX_DELAY_EN 0x0100 |
| |
| /* PHY Registers Field*/ |
| |
| /* Control Register fields offset:0*/ |
| /* bits 6,13: 10=1000, 01=100, 00=10 */ |
| #define F1_CTRL_SPEED_MSB 0x0040 |
| |
| /* Collision test enable */ |
| #define F1_CTRL_COLL_TEST_ENABLE 0x0080 |
| |
| /* FDX =1, half duplex =0 */ |
| #define F1_CTRL_FULL_DUPLEX 0x0100 |
| |
| /* Restart auto negotiation */ |
| #define F1_CTRL_RESTART_AUTONEGOTIATION 0x0200 |
| |
| /* Isolate PHY from MII */ |
| #define F1_CTRL_ISOLATE 0x0400 |
| |
| /* Power down */ |
| #define F1_CTRL_POWER_DOWN 0x0800 |
| |
| /* Auto Neg Enable */ |
| #define F1_CTRL_AUTONEGOTIATION_ENABLE 0x1000 |
| |
| /* bits 6,13: 10=1000, 01=100, 00=10 */ |
| #define F1_CTRL_SPEED_LSB 0x2000 |
| |
| /* 0 = normal, 1 = loopback */ |
| #define F1_LOCAL_LOOPBACK_ENABLE 0x4000 |
| #define F1_COMMON_CTRL 0x1040 |
| #define F1_10M_LOOPBACK 0x4100 |
| #define F1_100M_LOOPBACK 0x6100 |
| #define F1_1000M_LOOPBACK 0x4140 |
| |
| #define F1_PHY_MMD3_NUM 3 |
| #define F1_PHY_MMD3_ADDR_REMOTE_LOOPBACK_CTRL 0x805a |
| #define F1_PHY_REMOTE_LOOPBACK_ENABLE 0x0001 |
| #define F1_CTRL_SOFTWARE_RESET 0x8000 |
| |
| #define F1_CTRL_SPEED_MASK 0x2040 |
| #define F1_CTRL_SPEED_1000 0x0040 |
| #define F1_CTRL_SPEED_100 0x2000 |
| #define F1_CTRL_SPEED_10 0x0000 |
| |
| #define F1_RESET_DONE(phy_control) \ |
| (((phy_control) & (F1_CTRL_SOFTWARE_RESET)) == 0) |
| |
| /* Status Register fields offset:1*/ |
| /* Extended register capabilities */ |
| #define F1_STATUS_EXTENDED_CAPS 0x0001 |
| |
| /* Jabber Detected */ |
| #define F1_STATUS_JABBER_DETECT 0x0002 |
| |
| /* Link Status 1 = link */ |
| #define F1_STATUS_LINK_STATUS_UP 0x0004 |
| |
| /* Auto Neg Capable */ |
| #define F1_STATUS_AUTONEG_CAPS 0x0008 |
| |
| /* Remote Fault Detect */ |
| #define F1_STATUS_REMOTE_FAULT 0x0010 |
| |
| /* Auto Neg Complete */ |
| #define F1_STATUS_AUTO_NEG_DONE 0x0020 |
| |
| /* Preamble may be suppressed */ |
| #define F1_STATUS_PREAMBLE_SUPPRESS 0x0040 |
| |
| /* Ext. status info in Reg 0x0F */ |
| #define F1_STATUS_EXTENDED_STATUS 0x0100 |
| |
| /* 100T2 Half Duplex Capable */ |
| #define F1_STATUS_100T2_HD_CAPS 0x0200 |
| |
| /* 100T2 Full Duplex Capable */ |
| #define F1_STATUS_100T2_FD_CAPS 0x0400 |
| |
| /* 10T Half Duplex Capable */ |
| #define F1_STATUS_10T_HD_CAPS 0x0800 |
| |
| /* 10T Full Duplex Capable */ |
| #define F1_STATUS_10T_FD_CAPS 0x1000 |
| |
| /* 100X Half Duplex Capable */ |
| #define F1_STATUS_100X_HD_CAPS 0x2000 |
| |
| /* 100X Full Duplex Capable */ |
| #define F1_STATUS_100X_FD_CAPS 0x4000 |
| |
| /* 100T4 Capable */ |
| #define F1_STATUS_100T4_CAPS 0x8000 |
| |
| /* extended status register capabilities */ |
| |
| #define F1_STATUS_1000T_HD_CAPS 0x1000 |
| |
| #define F1_STATUS_1000T_FD_CAPS 0x2000 |
| |
| #define F1_STATUS_1000X_HD_CAPS 0x4000 |
| |
| #define F1_STATUS_1000X_FD_CAPS 0x8000 |
| |
| #define F1_AUTONEG_DONE(ip_phy_status) \ |
| (((ip_phy_status) & (F1_STATUS_AUTO_NEG_DONE)) == \ |
| (F1_STATUS_AUTO_NEG_DONE)) |
| |
| /* PHY identifier1 offset:2*/ |
| //Organizationally Unique Identifier bits 3:18 |
| |
| /* PHY identifier2 offset:3*/ |
| //Organizationally Unique Identifier bits 19:24 |
| |
| /* Auto-Negotiation Advertisement register. offset:4*/ |
| /* indicates IEEE 802.3 CSMA/CD */ |
| #define F1_ADVERTISE_SELECTOR_FIELD 0x0001 |
| |
| /* 10T Half Duplex Capable */ |
| #define F1_ADVERTISE_10HALF 0x0020 |
| |
| /* 10T Full Duplex Capable */ |
| #define F1_ADVERTISE_10FULL 0x0040 |
| |
| /* 100TX Half Duplex Capable */ |
| #define F1_ADVERTISE_100HALF 0x0080 |
| |
| /* 100TX Full Duplex Capable */ |
| #define F1_ADVERTISE_100FULL 0x0100 |
| |
| /* 100T4 Capable */ |
| #define F1_ADVERTISE_100T4 0x0200 |
| |
| /* Pause operation desired */ |
| #define F1_ADVERTISE_PAUSE 0x0400 |
| |
| /* Asymmetric Pause Direction bit */ |
| #define F1_ADVERTISE_ASYM_PAUSE 0x0800 |
| |
| /* Remote Fault detected */ |
| #define F1_ADVERTISE_REMOTE_FAULT 0x2000 |
| |
| /* Next Page ability supported */ |
| #define F1_ADVERTISE_NEXT_PAGE 0x8000 |
| |
| /* 100TX Half Duplex Capable */ |
| #define F1_ADVERTISE_1000HALF 0x0100 |
| |
| /* 100TX Full Duplex Capable */ |
| #define F1_ADVERTISE_1000FULL 0x0200 |
| |
| #define F1_ADVERTISE_ALL \ |
| (F1_ADVERTISE_10HALF | F1_ADVERTISE_10FULL | \ |
| F1_ADVERTISE_100HALF | F1_ADVERTISE_100FULL | \ |
| F1_ADVERTISE_1000FULL) |
| |
| #define F1_ADVERTISE_MEGA_ALL \ |
| (F1_ADVERTISE_10HALF | F1_ADVERTISE_10FULL | \ |
| F1_ADVERTISE_100HALF | F1_ADVERTISE_100FULL) |
| |
| /* Link Partner ability offset:5*/ |
| /* Same as advertise selector */ |
| #define F1_LINK_SLCT 0x001f |
| |
| /* Can do 10mbps half-duplex */ |
| #define F1_LINK_10BASETX_HALF_DUPLEX 0x0020 |
| |
| /* Can do 10mbps full-duplex */ |
| #define F1_LINK_10BASETX_FULL_DUPLEX 0x0040 |
| |
| /* Can do 100mbps half-duplex */ |
| #define F1_LINK_100BASETX_HALF_DUPLEX 0x0080 |
| |
| /* Can do 100mbps full-duplex */ |
| #define F1_LINK_100BASETX_FULL_DUPLEX 0x0100 |
| |
| /* Can do 1000mbps full-duplex */ |
| #define F1_LINK_1000BASETX_FULL_DUPLEX 0x0800 |
| |
| /* Can do 1000mbps half-duplex */ |
| #define F1_LINK_1000BASETX_HALF_DUPLEX 0x0400 |
| |
| /* 100BASE-T4 */ |
| #define F1_LINK_100BASE4 0x0200 |
| |
| /* PAUSE */ |
| #define F1_LINK_PAUSE 0x0400 |
| |
| /* Asymmetrical PAUSE */ |
| #define F1_LINK_ASYPAUSE 0x0800 |
| |
| /* Link partner faulted */ |
| #define F1_LINK_RFAULT 0x2000 |
| |
| /* Link partner acked us */ |
| #define F1_LINK_LPACK 0x4000 |
| |
| /* Next page bit */ |
| #define F1_LINK_NPAGE 0x8000 |
| |
| /* Auto-Negotiation Expansion Register offset:6 */ |
| |
| /* Next Page Transmit Register offset:7 */ |
| |
| /* Link partner Next Page Register offset:8*/ |
| |
| /* 1000BASE-T Control Register offset:9*/ |
| /* Advertise 1000T HD capability */ |
| #define F1_CTL_1000T_HD_CAPS 0x0100 |
| |
| /* Advertise 1000T FD capability */ |
| #define F1_CTL_1000T_FD_CAPS 0x0200 |
| |
| /* 1=Repeater/switch device port 0=DTE device*/ |
| #define F1_CTL_1000T_REPEATER_DTE 0x0400 |
| |
| /* 1=Configure PHY as Master 0=Configure PHY as Slave */ |
| #define F1_CTL_1000T_MS_VALUE 0x0800 |
| |
| /* 1=Master/Slave manual config value 0=Automatic Master/Slave config */ |
| #define F1_CTL_1000T_MS_ENABLE 0x1000 |
| |
| /* Normal Operation */ |
| #define F1_CTL_1000T_TEST_MODE_NORMAL 0x0000 |
| |
| /* Transmit Waveform test */ |
| #define F1_CTL_1000T_TEST_MODE_1 0x2000 |
| |
| /* Master Transmit Jitter test */ |
| #define F1_CTL_1000T_TEST_MODE_2 0x4000 |
| |
| /* Slave Transmit Jitter test */ |
| #define F1_CTL_1000T_TEST_MODE_3 0x6000 |
| |
| /* Transmitter Distortion test */ |
| #define F1_CTL_1000T_TEST_MODE_4 0x8000 |
| #define F1_CTL_1000T_SPEED_MASK 0x0300 |
| #define F1_CTL_1000T_DEFAULT_CAP_MASK 0x0300 |
| |
| /* 1000BASE-T Status Register offset:10 */ |
| /* LP is 1000T HD capable */ |
| #define F1_STATUS_1000T_LP_HD_CAPS 0x0400 |
| |
| /* LP is 1000T FD capable */ |
| #define F1_STATUS_1000T_LP_FD_CAPS 0x0800 |
| |
| /* Remote receiver OK */ |
| #define F1_STATUS_1000T_REMOTE_RX_STATUS 0x1000 |
| |
| /* Local receiver OK */ |
| #define F1_STATUS_1000T_LOCAL_RX_STATUS 0x2000 |
| |
| /* 1=Local TX is Master, 0=Slave */ |
| #define F1_STATUS_1000T_MS_CONFIG_RES 0x4000 |
| |
| #define F1_STATUS_1000T_MS_CONFIG_FAULT 0x8000 |
| |
| /* Master/Slave config fault */ |
| #define F1_STATUS_1000T_REMOTE_RX_STATUS_SHIFT 12 |
| #define F1_STATUS_1000T_LOCAL_RX_STATUS_SHIFT 13 |
| |
| /* Phy Specific Control Register offset:16*/ |
| /* 1=Jabber Function disabled */ |
| #define F1_CTL_JABBER_DISABLE 0x0001 |
| |
| /* 1=Polarity Reversal enabled */ |
| #define F1_CTL_POLARITY_REVERSAL 0x0002 |
| |
| /* 1=SQE Test enabled */ |
| #define F1_CTL_SQE_TEST 0x0004 |
| #define F1_CTL_MAC_POWERDOWN 0x0008 |
| |
| /* 1=CLK125 low, 0=CLK125 toggling |
| #define F1_CTL_CLK125_DISABLE 0x0010 |
| */ |
| /* MDI Crossover Mode bits 6:5 */ |
| /* Manual MDI configuration */ |
| #define F1_CTL_MDI_MANUAL_MODE 0x0000 |
| |
| /* Manual MDIX configuration */ |
| #define F1_CTL_MDIX_MANUAL_MODE 0x0020 |
| |
| /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */ |
| #define F1_CTL_AUTO_X_1000T 0x0040 |
| |
| /* Auto crossover enabled all speeds */ |
| #define F1_CTL_AUTO_X_MODE 0x0060 |
| |
| /* 1=Enable Extended 10BASE-T distance |
| * (Lower 10BASE-T RX Threshold) |
| * 0=Normal 10BASE-T RX Threshold */ |
| #define F1_CTL_10BT_EXT_DIST_ENABLE 0x0080 |
| |
| /* 1=5-Bit interface in 100BASE-TX |
| * 0=MII interface in 100BASE-TX */ |
| #define F1_CTL_MII_5BIT_ENABLE 0x0100 |
| |
| /* 1=Scrambler disable */ |
| #define F1_CTL_SCRAMBLER_DISABLE 0x0200 |
| |
| /* 1=Force link good */ |
| #define F1_CTL_FORCE_LINK_GOOD 0x0400 |
| |
| /* 1=Assert CRS on Transmit */ |
| #define F1_CTL_ASSERT_CRS_ON_TX 0x0800 |
| |
| #define F1_CTL_POLARITY_REVERSAL_SHIFT 1 |
| #define F1_CTL_AUTO_X_MODE_SHIFT 5 |
| #define F1_CTL_10BT_EXT_DIST_ENABLE_SHIFT 7 |
| |
| /* Phy Specific status fields offset:17*/ |
| /* 1=Speed & Duplex resolved */ |
| #define F1_STATUS_LINK_PASS 0x0400 |
| #define F1_STATUS_RESOVLED 0x0800 |
| |
| /* 1=Duplex 0=Half Duplex */ |
| #define F1_STATUS_FULL_DUPLEX 0x2000 |
| |
| /* Speed, bits 14:15 */ |
| #define F1_STATUS_SPEED 0xC000 |
| #define F1_STATUS_SPEED_MASK 0xC000 |
| |
| /* 00=10Mbs */ |
| #define F1_STATUS_SPEED_10MBS 0x0000 |
| |
| /* 01=100Mbs */ |
| #define F1_STATUS_SPEED_100MBS 0x4000 |
| |
| /* 10=1000Mbs */ |
| #define F1_STATUS_SPEED_1000MBS 0x8000 |
| #define F1_SPEED_DUPLEX_RESOVLED(phy_status) \ |
| (((phy_status) & \ |
| (F1_STATUS_RESOVLED)) == \ |
| (F1_STATUS_RESOVLED)) |
| |
| /*phy debug port1 register offset:29*/ |
| /*phy debug port2 register offset:30*/ |
| |
| /*F1 interrupt flag */ |
| #define F1_INTR_SPEED_CHANGE 0x4000 |
| #define F1_INTR_DUPLEX_CHANGE 0x2000 |
| #define F1_INTR_STATUS_UP_CHANGE 0x0400 |
| #define F1_INTR_STATUS_DOWN_CHANGE 0x0800 |
| |
| sw_error_t |
| f1_phy_set_powersave(a_uint32_t dev_id, a_uint32_t phy_id, a_bool_t enable); |
| |
| sw_error_t |
| f1_phy_get_powersave(a_uint32_t dev_id, a_uint32_t phy_id, a_bool_t *enable); |
| |
| sw_error_t |
| f1_phy_set_hibernate(a_uint32_t dev_id, a_uint32_t phy_id, a_bool_t enable); |
| |
| sw_error_t |
| f1_phy_get_hibernate(a_uint32_t dev_id, a_uint32_t phy_id, a_bool_t *enable); |
| |
| sw_error_t |
| f1_phy_cdt(a_uint32_t dev_id, a_uint32_t phy_id, a_uint32_t mdi_pair, |
| fal_cable_status_t *cable_status, a_uint32_t *cable_len) ; |
| |
| sw_error_t |
| f1_phy_set_duplex(a_uint32_t dev_id, a_uint32_t phy_id, |
| fal_port_duplex_t duplex); |
| |
| sw_error_t |
| f1_phy_get_duplex(a_uint32_t dev_id, a_uint32_t phy_id, |
| fal_port_duplex_t * duplex); |
| |
| sw_error_t |
| f1_phy_set_speed(a_uint32_t dev_id, a_uint32_t phy_id, |
| fal_port_speed_t speed); |
| |
| sw_error_t |
| f1_phy_get_speed(a_uint32_t dev_id, a_uint32_t phy_id, |
| fal_port_speed_t * speed); |
| |
| sw_error_t |
| f1_phy_restart_autoneg(a_uint32_t dev_id, a_uint32_t phy_id); |
| |
| sw_error_t |
| f1_phy_enable_autoneg(a_uint32_t dev_id, a_uint32_t phy_id); |
| |
| a_bool_t |
| f1_phy_get_link_status(a_uint32_t dev_id, a_uint32_t phy_id); |
| |
| sw_error_t |
| f1_phy_set_autoneg_adv(a_uint32_t dev_id, a_uint32_t phy_id, |
| a_uint32_t autoneg); |
| |
| sw_error_t |
| f1_phy_get_autoneg_adv(a_uint32_t dev_id, a_uint32_t phy_id, |
| a_uint32_t * autoneg); |
| |
| a_bool_t f1_phy_autoneg_status(a_uint32_t dev_id, a_uint32_t phy_id); |
| |
| sw_error_t |
| f1_phy_intr_mask_set(a_uint32_t dev_id, a_uint32_t phy_id, |
| a_uint32_t intr_mask_flag); |
| |
| sw_error_t |
| f1_phy_intr_mask_get(a_uint32_t dev_id, a_uint32_t phy_id, |
| a_uint32_t * intr_mask_flag); |
| |
| sw_error_t |
| f1_phy_intr_status_get(a_uint32_t dev_id, a_uint32_t phy_id, |
| a_uint32_t * intr_status_flag); |
| |
| sw_error_t |
| f1_phy_set_8023az(a_uint32_t dev_id, a_uint32_t phy_id, a_bool_t enable); |
| |
| sw_error_t |
| f1_phy_get_8023az(a_uint32_t dev_id, a_uint32_t phy_id, a_bool_t *enable); |
| |
| int |
| f1_phy_init(a_uint32_t dev_id, a_uint32_t port_bmp); |
| |
| #ifdef __cplusplus |
| } |
| #endif /* __cplusplus */ |
| #endif /* _F1_PHY_H_ */ |
