/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
 * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
 */

#ifndef __BOARD_CFG_H__
#define __BOARD_CFG_H__

#include <asm/arch/cpu.h>

/*
 * platform power init config
 */
#define AML_VDDCORE_INIT_VOLTAGE    840     // VCCK power up voltage
	/* If AML_VDDCORE_INIT_VOLTAGE_SEL is 1, the voltage of vddee
	 * will be controlled by efuse. if 0, it is controlled by
	 * AML_VDDCORE_INIT_VOLTAGE
	 */
#define AML_VDDCORE_INIT_VOLTAGE_SEL 			1
#define AML_VDDCORE_INIT_EFUSE_MARGIN			30
#define AML_VDDCORE_INIT_EFUSE_OFFSET			0xc8
#define AML_VDDCORE_INIT_EFUSE_BASE_V0LT		680

/* configs for CEC */
/* SMP Definitinos */
#define CPU_RELEASE_ADDR		secondary_boot_func

/* Serial config */
#define CONFIG_CONS_INDEX 2
#define CONFIG_BAUDRATE  115200

/* Enable ir remote wake up for bl30 */
#define AML_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power
#define AML_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+
#define AML_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch-
#define AML_IR_REMOTE_POWER_UP_KEY_VAL4 0XBA45BD02 //amlogic small ir--- power
#define AML_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04
#define AML_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF

/*config the default parameters for adc power key*/
#define AML_ADC_POWER_KEY_CHAN   2  /*channel range: 0-7*/
#define AML_ADC_POWER_KEY_VAL    0  /*sample value range: 0-1023*/

#define CONFIG_BOOTLOADER_CONTROL_BLOCK

#ifdef CONFIG_DTB_BIND_KERNEL	//load dtb from kernel, such as boot partition
#define CONFIG_DTB_LOAD  "imgread dtb boot ${dtb_mem_addr}"
#else
#define CONFIG_DTB_LOAD  "imgread dtb _aml_dtb ${dtb_mem_addr}"
#endif// #ifdef CONFIG_DTB_BIND_KERNEL	//load dtb from kernel, such as boot partition

/* args/envs */
#define CONFIG_SYS_MAXARGS  64
#define CONFIG_EXTRA_ENV_SETTINGS \
        "firstboot=1\0"\
        "upgrade_step=0\0"\
        "jtag=disable\0"\
        "loadaddr=0x00020000\0"\
        "os_ident_addr=0x00500000\0"\
        "loadaddr_rtos=0x00001000\0"\
        "loadaddr_kernel=0x00020000\0"\
        "otg_device=1\0" \
        "panel_type=lcd_1\0" \
        "outputmode=1080p60hz\0" \
        "hdmimode=1080p60hz\0" \
        "cvbsmode=576cvbs\0" \
        "display_width=1920\0" \
        "display_height=1080\0" \
        "display_bpp=16\0" \
        "display_color_index=16\0" \
        "display_layer=osd0\0" \
        "display_color_fg=0xffff\0" \
        "display_color_bg=0\0" \
        "dtb_mem_addr=0x01000000\0" \
        "fb_addr=0x00300000\0" \
        "fb_width=1920\0" \
        "fb_height=1080\0" \
        "frac_rate_policy=1\0" \
        "usb_burning=adnl 1000\0" \
        "fdt_high=0x20000000\0"\
        "sdcburncfg=aml_sdc_burn.ini\0"\
        "EnableSelinux=enforcing\0" \
        "recovery_part=recovery\0"\
        "recovery_offset=0\0"\
        "cvbs_drv=0\0"\
        "osd_reverse=0\0"\
        "video_reverse=0\0"\
        "boot_part=boot\0"\
        "Irq_check_en=0\0"\
        "common_dtb_load=" CONFIG_DTB_LOAD "\0"\
        "get_os_type=if store read ${os_ident_addr} ${boot_part} 0 0x1000; then os_ident ${os_ident_addr}; fi\0"\
        "fatload_dev=usb\0"\
        "fs_type=""rootfstype=ramfs""\0"\
        "initargs="\
            "init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xfe002000 "\
            "ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 "\
            "\0"\
        "upgrade_check="\
            "echo recovery_status=${recovery_status};"\
            "if itest.s \"${recovery_status}\" == \"in_progress\"; then "\
                "run storeargs; run recovery_from_flash;"\
            "else fi;"\
            "echo upgrade_step=${upgrade_step}; "\
            "if itest ${upgrade_step} == 3; then run storeargs; run update; fi;"\
            "\0"\
        "storeargs="\
            "get_bootloaderversion;" \
            "setenv bootargs ${initargs} ${fs_type} otg_device=${otg_device} "\
        "logo=${display_layer},loaded,${fb_addr} vout=${outputmode},enable panel_type=${panel_type} "\
                "hdmitx=${cecconfig},${colorattribute} hdmimode=${hdmimode} "\
                "frac_rate_policy=${frac_rate_policy} hdmi_read_edid=${hdmi_read_edid} cvbsmode=${cvbsmode} "\
                "osd_reverse=${osd_reverse} video_reverse=${video_reverse} irq_check_en=${Irq_check_en}  "\
                "androidboot.selinux=${EnableSelinux} androidboot.firstboot=${firstboot} jtag=${jtag}; "\
            "setenv bootargs ${bootargs} androidboot.bootloader=${bootloader_version} androidboot.hardware=amlogic;"\
            "run cmdline_keys;"\
            "\0"\
        "switch_bootmode="\
            "get_rebootmode;"\
            "if test ${reboot_mode} = factory_reset; then "\
                    "run recovery_from_flash;"\
            "else if test ${reboot_mode} = update; then "\
                    "run update;"\
            "else if test ${reboot_mode} = quiescent; then "\
                    "setenv bootargs ${bootargs} androidboot.quiescent=1;"\
            "else if test ${reboot_mode} = recovery_quiescent; then "\
                    "setenv bootargs ${bootargs} androidboot.quiescent=1;"\
                    "run recovery_from_flash;"\
            "else if test ${reboot_mode} = cold_boot; then "\
            "else if test ${reboot_mode} = fastboot; then "\
                "fastboot;"\
            "fi;fi;fi;fi;fi;fi;"\
            "\0" \
        "storeboot="\
            "run get_os_type;"\
            "if test ${os_type} = rtos; then "\
                "setenv loadaddr ${loadaddr_rtos};"\
                "store read ${loadaddr} ${boot_part} 0 0x400000;"\
                "bootm ${loadaddr};"\
            "else if test ${os_type} = kernel; then "\
                "if fdt addr ${dtb_mem_addr}; then else echo retry common dtb; run common_dtb_load; fi;"\
                "setenv loadaddr ${loadaddr_kernel};"\
                "if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;"\
            "else echo wrong OS format ${os_type}; fi;fi;"\
            "echo try upgrade as booting failure; run update;"\
            "\0" \
        "update="\
            /*first usb burning, second sdc_burn, third ext-sd autoscr/recovery, last udisk autoscr/recovery*/\
            "run usb_burning; "\
            "run recovery_from_udisk;"\
            "run recovery_from_flash;"\
            "\0"\
        "recovery_from_fat_dev="\
            "setenv loadaddr ${loadaddr_kernel};"\
            "if fatload ${fatload_dev} 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;"\
            "if fatload ${fatload_dev} 0 ${loadaddr} recovery.img; then "\
                "if fatload ${fatload_dev} 0 ${dtb_mem_addr} dtb.img; then echo ${fatload_dev} dtb.img loaded; fi;"\
                "bootm ${loadaddr};fi;"\
            "\0"\
        "recovery_from_udisk="\
            "setenv fatload_dev usb;"\
            "if usb start 0; then run recovery_from_fat_dev; fi;"\
            "\0"\
        "recovery_from_flash="\
            "setenv loadaddr ${loadaddr_kernel};"\
            "setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};"\
            "if imgread dtb recovery ${dtb_mem_addr}; then "\
                "else echo restore dtb; run common_dtb_load;"\
            "fi;"\
            "if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then bootm ${loadaddr}; fi;"\
            "\0"\
        "bcb_cmd="\
            "get_valid_slot;"\
            "\0"\
        "cmdline_keys="\
            "setenv usid 1234567890; setenv region_code US;"\
            "if keyman init 0x1234; then "\
                "if keyman read usid ${loadaddr} str; then fi;"\
                "if keyman read region_code ${loadaddr} str; then fi;"\
                "if keyman read mac ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} mac=${mac} androidboot.mac=${mac};"\
                "fi;"\
                "if keyman read deviceid ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} androidboot.deviceid=${deviceid};"\
                "fi;"\
                "if keyman read mac_wifi ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} mac_wifi=${mac_wifi} androidboot.mac_wifi=${mac_wifi};"\
                "fi;"\
                "if keyman read mac_bt ${loadaddr} str; then "\
                    "setenv bootargs ${bootargs} mac_bt=${mac_bt} androidboot.mac_bt=${mac_bt};"\
                "fi;"\
            "fi;"\
            "setenv bootargs ${bootargs} androidboot.wificountrycode=${region_code};"\
            "setenv bootargs ${bootargs} androidboot.serialno=${usid};"\
            "setenv serial ${usid}; setenv serial# ${usid};"\
            "\0"\

#define CONFIG_PREBOOT  \
            "run bcb_cmd; "\
            "run upgrade_check;"\
            "run storeargs;"

/* #define CONFIG_ENV_IS_NOWHERE  1 */
#define CONFIG_ENV_SIZE   (8*1024)
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_ANDROID_BOOT_IMAGE 1
#define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/

/* cpu */
/* #define CONFIG_CPU_CLK					1200 //MHz. Range: 360-2000, should be multiple of 24 */

/* ATTENTION */
/* DDR configs move to board/amlogic/[board]/firmware/timing.c */

/* running in sram */
#define UBOOT_RUN_IN_SRAM
#ifdef CONFIG_UBOOT_RUN_IN_SRAM
#define CONFIG_SYS_INIT_SP_ADDR				(0x00200000)
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN				(256*1024)
#else
#define CONFIG_SYS_INIT_SP_ADDR				(0x00200000)
#define CONFIG_SYS_MALLOC_LEN				(1*1024*1024)
#endif

/* ddr functions */
#define DDR_FULL_TEST            0 //0:disable, 1:enable. ddr full test
#define DDR_LOW_POWER            0 //0:disable, 1:enable. ddr clk gate for lp
#define DDR_ZQ_PD                0 //0:disable, 1:enable. ddr zq power down
#define DDR_USE_EXT_VREF         0 //0:disable, 1:enable. ddr use external vref
#define DDR4_TIMING_TEST         0 //0:disable, 1:enable. ddr4 timing test function
#define DDR_PLL_BYPASS           0 //0:disable, 1:enable. ddr pll bypass function

/* storage: emmc/nand/sd */
#define 	CONFIG_ENV_OVERWRITE
/* #define 	CONFIG_CMD_SAVEENV */
/* fixme, need fix*/

#if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE)
#error env in amlnand/mmc already be compatible;
#endif

/*
*				storage
*		|---------|---------|
*		|					|
*		emmc<--Compatible-->nand
*					|-------|-------|
*					|				|
*					MTD<-Exclusive->NFTL
*/
/* axg only support slc nand */
/* swither for mtd nand which is for slc only. */


#if defined(CONFIG_AML_NAND) && defined(CONFIG_MESON_NFC)
#error CONFIG_AML_NAND/CONFIG_MESON_NFC can not support at the sametime;
#endif

#if defined(CONFIG_SPI_NAND) && defined(CONFIG_MTD_SPI_NAND) && defined(CONFIG_MESON_NFC)
#error CONFIG_SPI_NAND/CONFIG_MTD_SPI_NAND/CONFIG_MESON_NFC can not support at the sametime;
#endif

/* #define		CONFIG_AML_SD_EMMC 1 */
#ifdef		CONFIG_AML_SD_EMMC
	#define 	CONFIG_GENERIC_MMC 1
	#define 	CONFIG_CMD_MMC 1
	#define CONFIG_CMD_GPT 1
	#define	CONFIG_SYS_MMC_ENV_DEV 1
	#define CONFIG_EMMC_DDR52_EN 0
	#define CONFIG_EMMC_DDR52_CLK 35000000
#endif
#define		CONFIG_PARTITIONS 1

#if defined CONFIG_MESON_NFC || defined CONFIG_SPI_NAND || defined CONFIG_MTD_SPI_NAND
	#define CONFIG_SYS_MAX_NAND_DEVICE  2
#endif

/* vpu */
#define AML_VPU_CLK_LEVEL_DFT 7

/* osd */
#define OSD_SCALE_ENABLE
#define AML_OSD_HIGH_VERSION

/* USB
 * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
 * Enable CONFIG_MUSB_UDD for Device functionalities.
 */
/* #define CONFIG_MUSB_UDC		1 */
/* #define CONFIG_CMD_USB 1 */

#define USB_PHY2_PLL_PARAMETER_1	0x09400414
#define USB_PHY2_PLL_PARAMETER_2	0x927e0000
#define USB_PHY2_PLL_PARAMETER_3	0xAC5F49E5

#define USB_G12x_PHY_PLL_SETTING_1	(0xfe18)
#define USB_G12x_PHY_PLL_SETTING_2	(0xfff)
#define USB_G12x_PHY_PLL_SETTING_3	(0x78000)
#define USB_G12x_PHY_PLL_SETTING_4	(0xe0004)
#define USB_G12x_PHY_PLL_SETTING_5	(0xe000c)

#define AML_TXLX_USB        1
#define AML_USB_V2             1
#define USB_GENERAL_BIT		4
#define USB_PHY21_BIT		6

/* UBOOT fastboot config */


/* UBOOT Facotry usb/sdcard burning config */


/* net */
/* #define CONFIG_CMD_NET   1 */
#define CONFIG_ETH_DESIGNWARE
#if defined(CONFIG_CMD_NET)
	#define CONFIG_DESIGNWARE_ETH 1
	#define CONFIG_PHYLIB	1
	#define CONFIG_NET_MULTI 1
	#define CONFIG_CMD_PING 1
	#define CONFIG_CMD_DHCP 1
	#define CONFIG_CMD_RARP 1
	#define CONFIG_HOSTNAME        "arm_gxbb"
#if 0
	#define CONFIG_RANDOM_ETHADDR  1				   /* use random eth addr, or default */
#endif
	#define CONFIG_ETHADDR         00:15:18:01:81:31   /* Ethernet address */
	#define CONFIG_IPADDR          10.18.9.97          /* Our ip address */
	#define CONFIG_GATEWAYIP       10.18.9.1           /* Our getway ip address */
	#define CONFIG_SERVERIP        10.18.9.113         /* Tftp server ip address */
	#define CONFIG_NETMASK         255.255.255.0
#endif /* (CONFIG_CMD_NET) */

#define MAC_ADDR_NEW  1

/* other devices */
#define CONFIG_SHA1 1
#define CONFIG_MD5 1

/*file system*/
#define CONFIG_DOS_PARTITION 1
#define CONFIG_EFI_PARTITION 1
#if 0
#define CONFIG_AML_PARTITION 1
#endif
/* #define CONFIG_MMC 1 */
#define CONFIG_FS_FAT 1
#define CONFIG_FS_EXT4 1
#define CONFIG_LZO 1

/* Cache Definitions */
/* #define CONFIG_SYS_DCACHE_OFF */
/* #define CONFIG_SYS_ICACHE_OFF */

/* other functions */
#define CONFIG_LIBAVB		1

#define CONFIG_CPU_ARMV8

/* #define CONFIG_MULTI_DTB    1 */

/* support secure boot */
#define CONFIG_AML_SECURE_UBOOT   1

#if defined(CONFIG_AML_SECURE_UBOOT)
/* unify build for generate encrypted bootloader "u-boot.bin.encrypt" */
#define CONFIG_AML_CRYPTO_UBOOT   1
#endif /* CONFIG_AML_SECURE_UBOOT */

#define CONFIG_FIP_IMG_SUPPORT  1

#define BL32_SHARE_MEM_SIZE  0x100000

#endif