// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
 */

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pwm/pwm.h>
#include <dt-bindings/pwm/meson.h>
#include <dt-bindings/clock/t3x-clkc.h>

/ {
	interrupt-parent = <&gic>;
	#address-cells = <2>;
	#size-cells = <2>;

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		/* 16 MiB reserved for Hardware ROM Firmware */
		hwrom_reserved: hwrom@0 {
			reg = <0x0 0x0 0x0 0x1000000>;
			no-map;
		};

		/* 2 MiB reserved for ARM Trusted Firmware (BL31) */
		secmon_reserved: secmon@10000000 {
			reg = <0x0 0x10000000 0x0 0x200000>;
			no-map;
		};

		linux,cma {
			compatible = "shared-dma-pool";
			reusable;
			size = <0x0 0xbc00000>;
			alignment = <0x0 0x400000>;
			linux,cma-default;
		};
	};

	cpus {
		#address-cells = <0x2>;
		#size-cells = <0x0>;

		cpu0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a53", "arm,armv8";
			reg = <0x0 0x0>;
			enable-method = "psci";
			next-level-cache = <&l2>;
			clocks = <&scpi_dvfs 0>;
		};

		cpu1: cpu@1 {
			device_type = "cpu";
			compatible = "arm,cortex-a53", "arm,armv8";
			reg = <0x0 0x1>;
			enable-method = "psci";
			next-level-cache = <&l2>;
			clocks = <&scpi_dvfs 0>;
		};

		cpu2: cpu@2 {
			device_type = "cpu";
			compatible = "arm,cortex-a53", "arm,armv8";
			reg = <0x0 0x2>;
			enable-method = "psci";
			next-level-cache = <&l2>;
			clocks = <&scpi_dvfs 0>;
		};

		cpu3: cpu@3 {
			device_type = "cpu";
			compatible = "arm,cortex-a53", "arm,armv8";
			reg = <0x0 0x3>;
			enable-method = "psci";
			next-level-cache = <&l2>;
			clocks = <&scpi_dvfs 0>;
		};

		l2: l2-cache0 {
			compatible = "cache";
		};
	};

	arm-pmu {
		compatible = "arm,cortex-a53-pmu";
		interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
	};

	psci {
		compatible = "arm,psci-0.2";
		method = "smc";
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13
			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14
			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11
			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10
			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
	};

	xtal: xtal-clk {
		compatible = "fixed-clock";
		clock-frequency = <24000000>;
		clock-output-names = "xtal";
		#clock-cells = <0>;
	};

	firmware {
		sm: secure-monitor {
			compatible = "amlogic,meson-gx-sm", "amlogic,meson-gxbb-sm";
		};
	};

	efuse: efuse {
		compatible = "amlogic,meson-sc2-efuse", "amlogic,meson-sc2-efuse";
		#address-cells = <1>;
		#size-cells = <1>;

	};

	scpi {
		compatible = "amlogic,meson-gxbb-scpi", "arm,scpi-pre-1.0";
		mboxes = <&mailbox 1 &mailbox 2>;
		shmem = <&cpu_scp_lpri &cpu_scp_hpri>;

		scpi_clocks: clocks {
			compatible = "arm,scpi-clocks";

			scpi_dvfs: scpi_clocks@0 {
				compatible = "arm,scpi-dvfs-clocks";
				#clock-cells = <1>;
				clock-indices = <0>;
				clock-output-names = "vcpu";
			};
		};

		scpi_sensors: sensors {
			compatible = "amlogic,meson-gxbb-scpi-sensors", "arm,scpi-sensors";
			#thermal-sensor-cells = <1>;
		};
	};

	soc {
		compatible = "simple-bus";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		gic: interrupt-controller@2c001000 {
			compatible = "arm,gic-400";
			reg = <0x0 0xffc01000 0 0x1000>,
			      <0x0 0xffc02000 0 0x2000>,
			      <0x0 0xffc04000 0 0x2000>,
			      <0x0 0xffc06000 0 0x2000>;
			interrupt-controller;
			interrupts = <GIC_PPI 9
				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
			#interrupt-cells = <3>;
			#address-cells = <0>;
		};

		sram: sram@f7000000 {
			compatible = "amlogic,meson-sc2-sram", "amlogic,meson-sc2-sram", "mmio-sram";
			reg = <0x0 0xf7000000 0x0 0x48000>;

			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0x0 0xf7000000 0x48000>;

			cpu_scp_lpri: scp-shmem@0 {
				compatible = "amlogic,meson-gx-scp-shmem", "amlogic,meson-gxbb-scp-shmem";
				reg = <0x47000 0x400>;
			};

			cpu_scp_hpri: scp-shmem@200 {
				compatible = "amlogic,meson-gx-scp-shmem", "amlogic,meson-gxbb-scp-shmem";
				reg = <0x47400 0x400>;
			};
		};

		cbus: cbus@fe070000 {
			compatible = "simple-bus";
			reg = <0x0 0xfe070000 0x0 0xF000>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges = <0x0 0x0 0x0 0xfe070000 0x0 0xF000>;

			uart_a: serial@8000 {
				compatible = "amlogic,meson-uart";
				reg = <0x0 0x8000 0x0 0x18>;
				clocks = <&xtal>;
				status = "disabled";
			};

			uart_b: serial@a000 {
				compatible = "amlogic,meson-uart";
				reg = <0x0 0xa000 0x0 0x18>;
				clocks = <&xtal>;
				status = "disabled";
			};

			ir: ir@8040 {
				compatible = "amlogic,meson-gx-ir", "amlogic,meson-gxbb-ir";
				reg = <0x0 0x8040 0x0 0x40>;
				interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
				status = "disabled";
			};

			reset: reset-controller@1000 {
				compatible = "amlogic,meson-gx-reset", "amlogic,meson-gxbb-reset";
				reg = <0x0 0x01000 0x0 0x1000>;
				#reset-cells = <1>;
			};

			uart_c: serial@22000 {
				compatible = "amlogic,meson-uart";
				reg = <0x0 0x22000 0x0 0x18>;
				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
				clocks = <&xtal>;
				status = "disabled";
			};

			jtag {
				compatible = "amlogic, jtag";
				status = "okay";
				select = "disable"; /* disable/jtag-a/jtag-b */
				pinctrl-names="jtag_a_pins";
				pinctrl-0=<&jtag_a_pins>;
			};
		};

		periphs: periphs@ff634000 {
			compatible = "simple-bus";
			reg = <0x0 0xff634000 0x0 0x2000>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges = <0x0 0x0 0x0 0xff634000 0x0 0x2000>;

			hwrng: rng {
				compatible = "amlogic,meson-rng";
				reg = <0x0 0x0 0x0 0x4>;
			};
		};

		hiubus: hiubus@ff63c000 {
			compatible = "simple-bus";
			reg = <0x0 0xff63c000 0x0 0x2000>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges = <0x0 0x0 0x0 0xff63c000 0x0 0x2000>;

			mailbox: mailbox@404 {
				compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
				reg = <0 0x404 0 0x4c>;
				interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
					     <0 209 IRQ_TYPE_EDGE_RISING>,
					     <0 210 IRQ_TYPE_EDGE_RISING>;
				#mbox-cells = <1>;
			};
		};

		clkc: clock-controller@0 {
			compatible = "amlogic,t3x-clkc";
			#clock-cells = <1>;
			reg = <0x0 0xfe000000 0x0 0x82e8>;
			clocks = <&xtal>;
			clock-names = "xtal";
		};

		spicc0: spi@fe050000 {
			compatible = "amlogic,meson-a4-spicc";
			reg = <0x0 0xfe050000 0x0 0x38>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spicc1: spi@fe050100 {
			compatible = "amlogic,meson-a4-spicc";
			reg = <0x0 0xfe050100 0x0 0x38>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spicc2: spi@fe050200 {
			compatible = "amlogic,meson-a4-spicc";
			reg = <0x0 0xfe050200 0x0 0x38>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spicc3: spi@fe050300 {
			compatible = "amlogic,meson-a4-spicc";
			reg = <0x0 0xfe050300 0x0 0x38>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spicc4: spi@fe050400 {
			compatible = "amlogic,meson-a4-spicc";
			reg = <0x0 0xfe050400 0x0 0x38>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spicc5: spi@fe050500 {
			compatible = "amlogic,meson-a4-spicc";
			reg = <0x0 0xfe050500 0x0 0x38>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c0: i2c@fe066000 {
			compatible = "amlogic,meson-i2c";
			reg = <0x0 0xfe066000 0x0 0x24>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c1: i2c@fe068000 {
			compatible = "amlogic,meson-i2c";
			reg = <0x0 0xfe068000 0x0 0x24>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c2: i2c@fe06a000 {
			compatible = "amlogic,meson-i2c";
			reg = <0x0 0xfe06a000 0x0 0x24>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c3: i2c@fe06c000 {
			compatible = "amlogic,meson-i2c";
			reg = <0x0 0xfe06c000 0x0 0x24>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		i2c4: i2c@fe06e000 {
			compatible = "amlogic,meson-i2c";
			reg = <0x0 0xfe06e000 0x0 0x24>;
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		spifc: spi@fe056000 {
			compatible = "amlogic,spifc";
			status = "disabled";
			reg = <0x0 0xfe056000 0x0 0x80>;
			/* clocks = <&clkc CLKID_CLK81>; */
			/* clock-names = "core"; */
			pinctrl-names = "default";
			pinctrl-0 = <&spifc_pins>;
			#address-cells = <1>;
			#size-cells = <0>;
			spi-flash@0 {
				compatible = "spi-flash";
				reg = <0>;
				spi-max-frequency = <20000000>;
				spi-tx-bus-width = <1>;
				spi-rx-bus-width = <1>;
				status = "disabled";
			};
			spi-nand@1 {
				compatible = "spi-nand";
				reg = <1>;
				spi-max-frequency = <20000000>;
				spi-tx-bus-width = <1>;
				spi-rx-bus-width = <1>;
				status = "disabled";
			};
		};

		ethmac: ethernet@ff3f0000 {
			compatible = "amlogic,g12a-eth-dwmac";
			phy_cntl1 = <0x41054147>;
			pll_val = <0x9c0040a 0x927e0000 0xac5f49e5>;
			analog_val = <0x20200000 0x0000c000 0x00000023>;
			status = "disabled";
		};

		saradc: adc@fe026000 {
			compatible = "amlogic,meson-saradc";
			reg = <0x0 0xfe026000 0x0 0x48>;
			status = "disabled";
		};

		nand: nfc@fe08d000 {
			compatible = "amlogic,meson-nfc";
			reg = <0x0 0xfe08d000 0x0 0x200>;
			interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>;
			status = "disabled";
			clk_reg = <0 0xfe08c000>;
		};

		apb: apb@fe000000 {
			compatible = "simple-bus";
			reg = <0x0 0xfe000000 0x0 0x1000000>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x1000000>;

			watchdog@2100 {
				compatible = "amlogic,meson-sc2-wdt";
				reg = <0x0 0x2100 0x0 0x10>;
				clocks = <&xtal>;
				clock-names = "wdt-clk";
			};

			sd_emmc_a: sdio {
				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
				reg = <0x0 0x88000 0x0 0x800>;
				interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
				status = "disabled";
				pinname = "sdio";
			};

			sd_emmc_b: sd {
				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
				reg = <0x0 0x8a000 0x0 0x800>;
				interrupts = <GIC_SPI 86 IRQ_TYPE_EDGE_RISING>;
				status = "disabled";
				pinname = "sd";
			};

			sd_emmc_c: emmc {
				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
				reg = <0x0 0x8c000 0x0 0x800>;
				interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>;
				status = "disabled";
				pinname = "emmc";
				//source-clock = <1152000000>;
			};
		};

		crg0: crg@fE3B0000 {
			compatible = "crg-xhci";
			status = "disable";
			reg = <0x0 0xfE3B0000 0x0 0x100000>;
			m31 = <1>;
		};

		crg1: crg@fE310000 {
			compatible = "crg-xhci";
			status = "disable";
			reg = <0x0 0xfE310000 0x0 0x100000>;
			m31 = <1>;
		};

		crg2: crg@fE3D0000 {
			compatible = "crg-xhci";
			status = "disable";
			reg = <0x0 0xfE3D0000 0x0 0x100000>;
			phys = <&usb2_phy_v2>, <&usb3_phy_v2>;
			phy-names = "usb2-phy", "usb3-phy";
		};

		usb2_phy_v2: usb20phy@fe046000 {
			compatible = "amlogic, amlogic-new-usb2-v2";
			status = "disable";
			#address-cells = <2>;
			#size-cells = <2>;
			phy-version = <2>;
			reg = <0x0 0xfe046000 0x0 0x00
					0x0 0xFE002000 0x0 0x100
					0x0 0xfe072000 0x0 0x2000
					0x0 0xfe042000 0x0 0x2000>;
			dwc2_a_reg = <0xfe3B0000>;
			#phy-cells = <0>;
		};

		usb3_phy_v2: usb30phy@fe046080 {
			compatible = "amlogic, amlogic-new-usb3-v2";
			status = "disable";
			#address-cells = <2>;
			#size-cells = <2>;
			phy-version = <3>;
			reg = <0x0 0xfe046080 0x0 0x20>;
			usb2-phy-reg = <0xfe046000>;
			usb2-phy-reg-size = <0x80>;
			#phy-cells = <0>;
		};

	};
};