blob: a7f2244b3be90238425ff73beea75dc8656edad0 [file] [log] [blame]
The PPC KVM paravirtual interface
=================================
The basic execution principle by which KVM on PowerPC works is to run all kernel
space code in PR=1 which is user space. This way we trap all privileged
instructions and can emulate them accordingly.
Unfortunately that is also the downfall. There are quite some privileged
instructions that needlessly return us to the hypervisor even though they
could be handled differently.
This is what the PPC PV interface helps with. It takes privileged instructions
and transforms them into unprivileged ones with some help from the hypervisor.
This cuts down virtualization costs by about 50% on some of my benchmarks.
The code for that interface can be found in arch/powerpc/kernel/kvm*
Querying for existence
======================
To find out if we're running on KVM or not, we leverage the device tree. When
Linux is running on KVM, a node /hypervisor exists. That node contains a
compatible property with the value "linux,kvm".
Once you determined you're running under a PV capable KVM, you can now use
hypercalls as described below.
KVM hypercalls
==============
Inside the device tree's /hypervisor node there's a property called
'hypercall-instructions'. This property contains at most 4 opcodes that make
up the hypercall. To call a hypercall, just call these instructions.
The parameters are as follows:
Register IN OUT
r0 - volatile
r3 1st parameter Return code
r4 2nd parameter 1st output value
r5 3rd parameter 2nd output value
r6 4th parameter 3rd output value
r7 5th parameter 4th output value
r8 6th parameter 5th output value
r9 7th parameter 6th output value
r10 8th parameter 7th output value
r11 hypercall number 8th output value
r12 - volatile
Hypercall definitions are shared in generic code, so the same hypercall numbers
apply for x86 and powerpc alike with the exception that each KVM hypercall
also needs to be ORed with the KVM vendor code which is (42 << 16).
Return codes can be as follows:
Code Meaning
0 Success
12 Hypercall not implemented
<0 Error
The magic page
==============
To enable communication between the hypervisor and guest there is a new shared
page that contains parts of supervisor visible register state. The guest can
map this shared page using the KVM hypercall KVM_HC_PPC_MAP_MAGIC_PAGE.
With this hypercall issued the guest always gets the magic page mapped at the
desired location in effective and physical address space. For now, we always
map the page to -4096. This way we can access it using absolute load and store
functions. The following instruction reads the first field of the magic page:
ld rX, -4096(0)
The interface is designed to be extensible should there be need later to add
additional registers to the magic page. If you add fields to the magic page,
also define a new hypercall feature to indicate that the host can give you more
registers. Only if the host supports the additional features, make use of them.
The magic page has the following layout as described in
arch/powerpc/include/asm/kvm_para.h:
struct kvm_vcpu_arch_shared {
__u64 scratch1;
__u64 scratch2;
__u64 scratch3;
__u64 critical; /* Guest may not get interrupts if == r1 */
__u64 sprg0;
__u64 sprg1;
__u64 sprg2;
__u64 sprg3;
__u64 srr0;
__u64 srr1;
__u64 dar;
__u64 msr;
__u32 dsisr;
__u32 int_pending; /* Tells the guest if we have an interrupt */
};
Additions to the page must only occur at the end. Struct fields are always 32
or 64 bit aligned, depending on them being 32 or 64 bit wide respectively.
Magic page features
===================
When mapping the magic page using the KVM hypercall KVM_HC_PPC_MAP_MAGIC_PAGE,
a second return value is passed to the guest. This second return value contains
a bitmap of available features inside the magic page.
The following enhancements to the magic page are currently available:
KVM_MAGIC_FEAT_SR Maps SR registers r/w in the magic page
For enhanced features in the magic page, please check for the existence of the
feature before using them!
MSR bits
========
The MSR contains bits that require hypervisor intervention and bits that do
not require direct hypervisor intervention because they only get interpreted
when entering the guest or don't have any impact on the hypervisor's behavior.
The following bits are safe to be set inside the guest:
MSR_EE
MSR_RI
MSR_CR
MSR_ME
If any other bit changes in the MSR, please still use mtmsr(d).
Patched instructions
====================
The "ld" and "std" instructions are transormed to "lwz" and "stw" instructions
respectively on 32 bit systems with an added offset of 4 to accomodate for big
endianness.
The following is a list of mapping the Linux kernel performs when running as
guest. Implementing any of those mappings is optional, as the instruction traps
also act on the shared page. So calling privileged instructions still works as
before.
From To
==== ==
mfmsr rX ld rX, magic_page->msr
mfsprg rX, 0 ld rX, magic_page->sprg0
mfsprg rX, 1 ld rX, magic_page->sprg1
mfsprg rX, 2 ld rX, magic_page->sprg2
mfsprg rX, 3 ld rX, magic_page->sprg3
mfsrr0 rX ld rX, magic_page->srr0
mfsrr1 rX ld rX, magic_page->srr1
mfdar rX ld rX, magic_page->dar
mfdsisr rX lwz rX, magic_page->dsisr
mtmsr rX std rX, magic_page->msr
mtsprg 0, rX std rX, magic_page->sprg0
mtsprg 1, rX std rX, magic_page->sprg1
mtsprg 2, rX std rX, magic_page->sprg2
mtsprg 3, rX std rX, magic_page->sprg3
mtsrr0 rX std rX, magic_page->srr0
mtsrr1 rX std rX, magic_page->srr1
mtdar rX std rX, magic_page->dar
mtdsisr rX stw rX, magic_page->dsisr
tlbsync nop
mtmsrd rX, 0 b <special mtmsr section>
mtmsr rX b <special mtmsr section>
mtmsrd rX, 1 b <special mtmsrd section>
[Book3S only]
mtsrin rX, rY b <special mtsrin section>
[BookE only]
wrteei [0|1] b <special wrteei section>
Some instructions require more logic to determine what's going on than a load
or store instruction can deliver. To enable patching of those, we keep some
RAM around where we can live translate instructions to. What happens is the
following:
1) copy emulation code to memory
2) patch that code to fit the emulated instruction
3) patch that code to return to the original pc + 4
4) patch the original instruction to branch to the new code
That way we can inject an arbitrary amount of code as replacement for a single
instruction. This allows us to check for pending interrupts when setting EE=1
for example.