| /** | |
| ****************************************************************************** | |
| * @file system_stm32f4xx.c | |
| * @author MCD Application Team | |
| * @version V1.0.0 | |
| * @date 24-October-2011 | |
| * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File. | |
| * This file contains the system clock configuration for STM32F4xx devices, | |
| * and is generated by the clock configuration tool | |
| * stm32f4xx_Clock_Configuration_V1.0.0.xls | |
| * | |
| * 1. This file provides two functions and one global variable to be called from | |
| * user application: | |
| * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier | |
| * and Divider factors, AHB/APBx prescalers and Flash settings), | |
| * depending on the configuration made in the clock xls tool. | |
| * This function is called at startup just after reset and | |
| * before branch to main program. This call is made inside | |
| * the "startup_stm32f4xx.s" file. | |
| * | |
| * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used | |
| * by the user application to setup the SysTick | |
| * timer or configure other parameters. | |
| * | |
| * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must | |
| * be called whenever the core clock is changed | |
| * during program execution. | |
| * | |
| * 2. After each device reset the HSI (16 MHz) is used as system clock source. | |
| * Then SystemInit() function is called, in "startup_stm32f4xx.s" file, to | |
| * configure the system clock before to branch to main program. | |
| * | |
| * 3. If the system clock source selected by user fails to startup, the SystemInit() | |
| * function will do nothing and HSI still used as system clock source. User can | |
| * add some code to deal with this issue inside the SetSysClock() function. | |
| * | |
| * 4. The default value of HSE crystal is set to 25MHz, refer to "HSE_VALUE" define | |
| * in "stm32f4xx.h" file. When HSE is used as system clock source, directly or | |
| * through PLL, and you are using different crystal you have to adapt the HSE | |
| * value to your own configuration. | |
| * | |
| * 5. This file configures the system clock as follows: | |
| *============================================================================= | |
| *============================================================================= | |
| * Supported STM32F4xx device revision | Rev A | |
| *----------------------------------------------------------------------------- | |
| * System Clock source | PLL (HSE) | |
| *----------------------------------------------------------------------------- | |
| * SYSCLK(Hz) | 150000000 | |
| *----------------------------------------------------------------------------- | |
| * HCLK(Hz) | 150000000 | |
| *----------------------------------------------------------------------------- | |
| * AHB Prescaler | 1 | |
| *----------------------------------------------------------------------------- | |
| * APB1 Prescaler | 4 | |
| *----------------------------------------------------------------------------- | |
| * APB2 Prescaler | 2 | |
| *----------------------------------------------------------------------------- | |
| * HSE Frequency(Hz) | 25000000 | |
| *----------------------------------------------------------------------------- | |
| * PLL_M | 25 | |
| *----------------------------------------------------------------------------- | |
| * PLL_N | 300 | |
| *----------------------------------------------------------------------------- | |
| * PLL_P | 2 | |
| *----------------------------------------------------------------------------- | |
| * PLL_Q | 7 | |
| *----------------------------------------------------------------------------- | |
| * PLLI2S_N | NA | |
| *----------------------------------------------------------------------------- | |
| * PLLI2S_R | NA | |
| *----------------------------------------------------------------------------- | |
| * I2S input clock | NA | |
| *----------------------------------------------------------------------------- | |
| * VDD(V) | 3.3 | |
| *----------------------------------------------------------------------------- | |
| * Main regulator output voltage | Scale1 mode | |
| *----------------------------------------------------------------------------- | |
| * Flash Latency(WS) | 4 | |
| *----------------------------------------------------------------------------- | |
| * Prefetch Buffer | OFF | |
| *----------------------------------------------------------------------------- | |
| * Instruction cache | ON | |
| *----------------------------------------------------------------------------- | |
| * Data cache | ON | |
| *----------------------------------------------------------------------------- | |
| * Require 48MHz for USB OTG FS, | Disabled | |
| * SDIO and RNG clock | | |
| *----------------------------------------------------------------------------- | |
| *============================================================================= | |
| ****************************************************************************** | |
| * @attention | |
| * | |
| * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS | |
| * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE | |
| * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY | |
| * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING | |
| * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE | |
| * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. | |
| * | |
| * <h2><center>© COPYRIGHT 2011 STMicroelectronics</center></h2> | |
| ****************************************************************************** | |
| */ | |
| /** @addtogroup CMSIS | |
| * @{ | |
| */ | |
| /** @addtogroup stm32f4xx_system | |
| * @{ | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_Includes | |
| * @{ | |
| */ | |
| #include "stm32f4xx.h" | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_TypesDefinitions | |
| * @{ | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_Defines | |
| * @{ | |
| */ | |
| /************************* Miscellaneous Configuration ************************/ | |
| /*!< Uncomment the following line if you need to use external SRAM mounted | |
| on STM324xG_EVAL board as data memory */ | |
| /* #define DATA_IN_ExtSRAM */ | |
| /*!< Uncomment the following line if you need to relocate your vector Table in | |
| Internal SRAM. */ | |
| /* #define VECT_TAB_SRAM */ | |
| #define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field. | |
| This value must be a multiple of 0x200. */ | |
| /******************************************************************************/ | |
| /************************* PLL Parameters *************************************/ | |
| /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N */ | |
| #define PLL_M 25 | |
| #define PLL_N 300 | |
| /* SYSCLK = PLL_VCO / PLL_P */ | |
| #define PLL_P 2 | |
| /* USB OTG FS, SDIO and RNG Clock = PLL_VCO / PLLQ */ | |
| #define PLL_Q 7 | |
| /******************************************************************************/ | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_Macros | |
| * @{ | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_Variables | |
| * @{ | |
| */ | |
| uint32_t SystemCoreClock = 150000000; | |
| __I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_FunctionPrototypes | |
| * @{ | |
| */ | |
| static void SetSysClock(void); | |
| #ifdef DATA_IN_ExtSRAM | |
| static void SystemInit_ExtMemCtl(void); | |
| #endif /* DATA_IN_ExtSRAM */ | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup STM32F4xx_System_Private_Functions | |
| * @{ | |
| */ | |
| /** | |
| * @brief Setup the microcontroller system | |
| * Initialize the Embedded Flash Interface, the PLL and update the | |
| * SystemFrequency variable. | |
| * @param None | |
| * @retval None | |
| */ | |
| void SystemInit(void) | |
| { | |
| /* FPU settings ------------------------------------------------------------*/ | |
| #if (__FPU_PRESENT == 1) && (__FPU_USED == 1) | |
| SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */ | |
| #endif | |
| /* Reset the RCC clock configuration to the default reset state ------------*/ | |
| /* Set HSION bit */ | |
| RCC->CR |= (uint32_t)0x00000001; | |
| /* Reset CFGR register */ | |
| RCC->CFGR = 0x00000000; | |
| /* Reset HSEON, CSSON and PLLON bits */ | |
| RCC->CR &= (uint32_t)0xFEF6FFFF; | |
| /* Reset PLLCFGR register */ | |
| RCC->PLLCFGR = 0x24003010; | |
| /* Reset HSEBYP bit */ | |
| RCC->CR &= (uint32_t)0xFFFBFFFF; | |
| /* Disable all interrupts */ | |
| RCC->CIR = 0x00000000; | |
| #ifdef DATA_IN_ExtSRAM | |
| SystemInit_ExtMemCtl(); | |
| #endif /* DATA_IN_ExtSRAM */ | |
| /* Configure the System clock source, PLL Multiplier and Divider factors, | |
| AHB/APBx prescalers and Flash settings ----------------------------------*/ | |
| SetSysClock(); | |
| /* Configure the Vector Table location add offset address ------------------*/ | |
| #ifdef VECT_TAB_SRAM | |
| SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */ | |
| #else | |
| SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */ | |
| #endif | |
| } | |
| /** | |
| * @brief Update SystemCoreClock variable according to Clock Register Values. | |
| * The SystemCoreClock variable contains the core clock (HCLK), it can | |
| * be used by the user application to setup the SysTick timer or configure | |
| * other parameters. | |
| * | |
| * @note Each time the core clock (HCLK) changes, this function must be called | |
| * to update SystemCoreClock variable value. Otherwise, any configuration | |
| * based on this variable will be incorrect. | |
| * | |
| * @note - The system frequency computed by this function is not the real | |
| * frequency in the chip. It is calculated based on the predefined | |
| * constant and the selected clock source: | |
| * | |
| * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) | |
| * | |
| * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) | |
| * | |
| * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) | |
| * or HSI_VALUE(*) multiplied/divided by the PLL factors. | |
| * | |
| * (*) HSI_VALUE is a constant defined in stm32f4xx.h file (default value | |
| * 16 MHz) but the real value may vary depending on the variations | |
| * in voltage and temperature. | |
| * | |
| * (**) HSE_VALUE is a constant defined in stm32f4xx.h file (default value | |
| * 25 MHz), user has to ensure that HSE_VALUE is same as the real | |
| * frequency of the crystal used. Otherwise, this function may | |
| * have wrong result. | |
| * | |
| * - The result of this function could be not correct when using fractional | |
| * value for HSE crystal. | |
| * | |
| * @param None | |
| * @retval None | |
| */ | |
| void SystemCoreClockUpdate(void) | |
| { | |
| uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2; | |
| /* Get SYSCLK source -------------------------------------------------------*/ | |
| tmp = RCC->CFGR & RCC_CFGR_SWS; | |
| switch (tmp) | |
| { | |
| case 0x00: /* HSI used as system clock source */ | |
| SystemCoreClock = HSI_VALUE; | |
| break; | |
| case 0x04: /* HSE used as system clock source */ | |
| SystemCoreClock = HSE_VALUE; | |
| break; | |
| case 0x08: /* PLL used as system clock source */ | |
| /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N | |
| SYSCLK = PLL_VCO / PLL_P | |
| */ | |
| pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22; | |
| pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; | |
| if (pllsource != 0) | |
| { | |
| /* HSE used as PLL clock source */ | |
| pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6); | |
| } | |
| else | |
| { | |
| /* HSI used as PLL clock source */ | |
| pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6); | |
| } | |
| pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2; | |
| SystemCoreClock = pllvco/pllp; | |
| break; | |
| default: | |
| SystemCoreClock = HSI_VALUE; | |
| break; | |
| } | |
| /* Compute HCLK frequency --------------------------------------------------*/ | |
| /* Get HCLK prescaler */ | |
| tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; | |
| /* HCLK frequency */ | |
| SystemCoreClock >>= tmp; | |
| } | |
| /** | |
| * @brief Configures the System clock source, PLL Multiplier and Divider factors, | |
| * AHB/APBx prescalers and Flash settings | |
| * @Note This function should be called only once the RCC clock configuration | |
| * is reset to the default reset state (done in SystemInit() function). | |
| * @param None | |
| * @retval None | |
| */ | |
| static void SetSysClock(void) | |
| { | |
| /******************************************************************************/ | |
| /* PLL (clocked by HSE) used as System clock source */ | |
| /******************************************************************************/ | |
| __IO uint32_t StartUpCounter = 0, HSEStatus = 0; | |
| /* Enable HSE */ | |
| RCC->CR |= ((uint32_t)RCC_CR_HSEON); | |
| /* Wait till HSE is ready and if Time out is reached exit */ | |
| do | |
| { | |
| HSEStatus = RCC->CR & RCC_CR_HSERDY; | |
| StartUpCounter++; | |
| } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); | |
| if ((RCC->CR & RCC_CR_HSERDY) != RESET) | |
| { | |
| HSEStatus = (uint32_t)0x01; | |
| } | |
| else | |
| { | |
| HSEStatus = (uint32_t)0x00; | |
| } | |
| if (HSEStatus == (uint32_t)0x01) | |
| { | |
| /* Select regulator voltage output Scale 1 mode, System frequency up to 168 MHz */ | |
| RCC->APB1ENR |= RCC_APB1ENR_PWREN; | |
| PWR->CR |= PWR_CR_VOS; | |
| /* HCLK = SYSCLK / 1*/ | |
| RCC->CFGR |= RCC_CFGR_HPRE_DIV1; | |
| /* PCLK2 = HCLK / 2*/ | |
| RCC->CFGR |= RCC_CFGR_PPRE2_DIV2; | |
| /* PCLK1 = HCLK / 4*/ | |
| RCC->CFGR |= RCC_CFGR_PPRE1_DIV4; | |
| /* Configure the main PLL */ | |
| RCC->PLLCFGR = PLL_M | (PLL_N << 6) | (((PLL_P >> 1) -1) << 16) | | |
| (RCC_PLLCFGR_PLLSRC_HSE) | (PLL_Q << 24); | |
| /* Enable the main PLL */ | |
| RCC->CR |= RCC_CR_PLLON; | |
| /* Wait till the main PLL is ready */ | |
| while((RCC->CR & RCC_CR_PLLRDY) == 0) | |
| { | |
| } | |
| /* Configure Flash prefetch, Instruction cache, Data cache and wait state */ | |
| FLASH->ACR = FLASH_ACR_ICEN |FLASH_ACR_DCEN |FLASH_ACR_LATENCY_4WS; | |
| /* Select the main PLL as system clock source */ | |
| RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); | |
| RCC->CFGR |= RCC_CFGR_SW_PLL; | |
| /* Wait till the main PLL is used as system clock source */ | |
| while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS ) != RCC_CFGR_SWS_PLL); | |
| { | |
| } | |
| } | |
| else | |
| { /* If HSE fails to start-up, the application will have wrong clock | |
| configuration. User can add here some code to deal with this error */ | |
| } | |
| } | |
| /** | |
| * @brief Setup the external memory controller. Called in startup_stm32f4xx.s | |
| * before jump to __main | |
| * @param None | |
| * @retval None | |
| */ | |
| #ifdef DATA_IN_ExtSRAM | |
| /** | |
| * @brief Setup the external memory controller. | |
| * Called in startup_stm32f4xx.s before jump to main. | |
| * This function configures the external SRAM mounted on STM324xG_EVAL board | |
| * This SRAM will be used as program data memory (including heap and stack). | |
| * @param None | |
| * @retval None | |
| */ | |
| void SystemInit_ExtMemCtl(void) | |
| { | |
| /*-- GPIOs Configuration -----------------------------------------------------*/ | |
| /* | |
| +-------------------+--------------------+------------------+------------------+ | |
| + SRAM pins assignment + | |
| +-------------------+--------------------+------------------+------------------+ | |
| | PD0 <-> FSMC_D2 | PE0 <-> FSMC_NBL0 | PF0 <-> FSMC_A0 | PG0 <-> FSMC_A10 | | |
| | PD1 <-> FSMC_D3 | PE1 <-> FSMC_NBL1 | PF1 <-> FSMC_A1 | PG1 <-> FSMC_A11 | | |
| | PD4 <-> FSMC_NOE | PE3 <-> FSMC_A19 | PF2 <-> FSMC_A2 | PG2 <-> FSMC_A12 | | |
| | PD5 <-> FSMC_NWE | PE4 <-> FSMC_A20 | PF3 <-> FSMC_A3 | PG3 <-> FSMC_A13 | | |
| | PD8 <-> FSMC_D13 | PE7 <-> FSMC_D4 | PF4 <-> FSMC_A4 | PG4 <-> FSMC_A14 | | |
| | PD9 <-> FSMC_D14 | PE8 <-> FSMC_D5 | PF5 <-> FSMC_A5 | PG5 <-> FSMC_A15 | | |
| | PD10 <-> FSMC_D15 | PE9 <-> FSMC_D6 | PF12 <-> FSMC_A6 | PG9 <-> FSMC_NE2 | | |
| | PD11 <-> FSMC_A16 | PE10 <-> FSMC_D7 | PF13 <-> FSMC_A7 |------------------+ | |
| | PD12 <-> FSMC_A17 | PE11 <-> FSMC_D8 | PF14 <-> FSMC_A8 | | |
| | PD13 <-> FSMC_A18 | PE12 <-> FSMC_D9 | PF15 <-> FSMC_A9 | | |
| | PD14 <-> FSMC_D0 | PE13 <-> FSMC_D10 |------------------+ | |
| | PD15 <-> FSMC_D1 | PE14 <-> FSMC_D11 | | |
| | | PE15 <-> FSMC_D12 | | |
| +-------------------+--------------------+ | |
| */ | |
| /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */ | |
| RCC->AHB1ENR = 0x00000078; | |
| /* Connect PDx pins to FSMC Alternate function */ | |
| GPIOD->AFR[0] = 0x00cc00cc; | |
| GPIOD->AFR[1] = 0xcc0ccccc; | |
| /* Configure PDx pins in Alternate function mode */ | |
| GPIOD->MODER = 0xaaaa0a0a; | |
| /* Configure PDx pins speed to 100 MHz */ | |
| GPIOD->OSPEEDR = 0xffff0f0f; | |
| /* Configure PDx pins Output type to push-pull */ | |
| GPIOD->OTYPER = 0x00000000; | |
| /* No pull-up, pull-down for PDx pins */ | |
| GPIOD->PUPDR = 0x00000000; | |
| /* Connect PEx pins to FSMC Alternate function */ | |
| GPIOE->AFR[0] = 0xc00cc0cc; | |
| GPIOE->AFR[1] = 0xcccccccc; | |
| /* Configure PEx pins in Alternate function mode */ | |
| GPIOE->MODER = 0xaaaa828a; | |
| /* Configure PEx pins speed to 100 MHz */ | |
| GPIOE->OSPEEDR = 0xffffc3cf; | |
| /* Configure PEx pins Output type to push-pull */ | |
| GPIOE->OTYPER = 0x00000000; | |
| /* No pull-up, pull-down for PEx pins */ | |
| GPIOE->PUPDR = 0x00000000; | |
| /* Connect PFx pins to FSMC Alternate function */ | |
| GPIOF->AFR[0] = 0x00cccccc; | |
| GPIOF->AFR[1] = 0xcccc0000; | |
| /* Configure PFx pins in Alternate function mode */ | |
| GPIOF->MODER = 0xaa000aaa; | |
| /* Configure PFx pins speed to 100 MHz */ | |
| GPIOF->OSPEEDR = 0xff000fff; | |
| /* Configure PFx pins Output type to push-pull */ | |
| GPIOF->OTYPER = 0x00000000; | |
| /* No pull-up, pull-down for PFx pins */ | |
| GPIOF->PUPDR = 0x00000000; | |
| /* Connect PGx pins to FSMC Alternate function */ | |
| GPIOG->AFR[0] = 0x00cccccc; | |
| GPIOG->AFR[1] = 0x000000c0; | |
| /* Configure PGx pins in Alternate function mode */ | |
| GPIOG->MODER = 0x00080aaa; | |
| /* Configure PGx pins speed to 100 MHz */ | |
| GPIOG->OSPEEDR = 0x000c0fff; | |
| /* Configure PGx pins Output type to push-pull */ | |
| GPIOG->OTYPER = 0x00000000; | |
| /* No pull-up, pull-down for PGx pins */ | |
| GPIOG->PUPDR = 0x00000000; | |
| /*-- FSMC Configuration ------------------------------------------------------*/ | |
| /* Enable the FSMC interface clock */ | |
| RCC->AHB3ENR = 0x00000001; | |
| /* Configure and enable Bank1_SRAM2 */ | |
| FSMC_Bank1->BTCR[2] = 0x00001015; | |
| FSMC_Bank1->BTCR[3] = 0x00010603; | |
| FSMC_Bank1E->BWTR[2] = 0x0fffffff; | |
| /* | |
| Bank1_SRAM2 is configured as follow: | |
| p.FSMC_AddressSetupTime = 3; | |
| p.FSMC_AddressHoldTime = 0; | |
| p.FSMC_DataSetupTime = 6; | |
| p.FSMC_BusTurnAroundDuration = 1; | |
| p.FSMC_CLKDivision = 0; | |
| p.FSMC_DataLatency = 0; | |
| p.FSMC_AccessMode = FSMC_AccessMode_A; | |
| FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM2; | |
| FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_MemoryType = FSMC_MemoryType_PSRAM; | |
| FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b; | |
| FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode = FSMC_BurstAccessMode_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait = FSMC_AsynchronousWait_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low; | |
| FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState; | |
| FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable; | |
| FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable; | |
| FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &p; | |
| FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &p; | |
| */ | |
| } | |
| #endif /* DATA_IN_ExtSRAM */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ | |