FreeRTOSV8.0.1/FreeRTOS/Demo/CORTEX_A2F200_IAR_and_Keil/MicroSemi_Code/drivers/I2C/i2c.h

/*******************************************************************************
 * (c) Copyright 2007-2008 Actel Corporation.  All rights reserved.
 *
 * SmartFusion microcontroller subsystem I2C bare metal software driver public
 * API.
 *
 * SVN $Revision: 2150 $
 * SVN $Date: 2010-02-11 14:39:24 +0000 (Thu, 11 Feb 2010) $
 */
/*=========================================================================*//**
  @mainpage SmartFusion MSS I2C Bare Metal Driver.

  @section intro_sec Introduction
  The SmartFusion™ microcontroller subsystem (MSS) includes two I2C peripherals
  for serial communication. This driver provides a set of functions for
  controlling the MSS I2Cs as part of a bare metal system where no operating
  system is available. These drivers can be adapted for use as part of an
  operating system, but the implementation of the adaptation layer between this
  driver and the operating system's driver model is outside the scope of this
  driver.

  @section hw_dependencies Hardware Flow Dependencies
  The configuration of all features of the MSS I2Cs is covered by this driver
  with the exception of the SmartFusion IOMUX configuration. SmartFusion allows
  multiple non-concurrent uses of some external pins through IOMUX configuration.
  This feature allows optimization of external pin usage by assigning external
  pins for use by either the microcontroller subsystem or the FPGA fabric. The
  MSS I2Cs serial signals are routed through IOMUXes to the SmartFusion device
  external pins. These IOMUXes are automatically configured correctly by the MSS
  configurator tool in the hardware flow when the MSS I2Cs are enabled in that
  tool. You must ensure that the MSS I2Cs are enabled by the MSS configurator
  tool in the hardware flow; otherwise the serial inputs and outputs will not be
  connected to the chip's external pins. For more information on IOMUX, refer to
  the IOMUX section of the SmartFusion Datasheet.
  The base address, register addresses and interrupt number assignment for the
  MSS I2C blocks are defined as constants in the SmartFusion CMSIS-PAL. You must
  ensure that the SmartFusion CMSIS-PAL is either included in the software tool
  chain used to build your project or is included in your project.

  @section theory_op Theory of Operation
  The MSS I2C driver functions are grouped into the following categories:
    • Initialization and configuration functions
    • Interrupt control
    • I2C master operations – functions to handle write, read and write-read transactions
    • I2C slave operations – functions to handle write, read and write-read transactions

  Initialization and Configuration
    The MSS I2C driver is initialized through a call to the MSS_I2C_init()
    function. This function takes the MSS I2C's configuration as parameters. The
    MSS_I2C_init() function must be called before any other MSS I2C driver
    functions can be called. The first parameter of the MSS_I2C_init() function
    is a pointer to one of two global data structures used by the driver to
    store state information for each MSS I2C. A pointer to these data structures
    is also used as first parameter to any of the driver functions to identify
    which MSS I2C will be used by the called function. The names of these two
    data structures are g_mss_i2c0 and g_mss_i2c1. Therefore any call to an MSS
    I2C driver function should be of the form MSS_I2C_function_name( &g_mss_i2c0, ... )
    or MSS_I2C_function_name( &g_mss_i2c1, ... ).
    The MSS_I2C_init() function call for each MSS I2C also takes the I2C serial
    address assigned to the MSS I2C and the serial clock divider to be used to
    generate its I2C clock as configuration parameters.

  Interrupt Control
    The MSS I2C driver is interrupt driven and it enables and disables the
    generation of interrupts by MSS I2C at various times when it is operating.
    The driver automatically handles MSS I2C interrupts internally, including
    enabling disabling and clearing MSS I2C interrupts in the Cortex-M3
    interrupt controller when required.
    The function MSS_I2C_register_write_handler() is used to register a write
    handler function with the MSS I2C driver that it will call on completion of
    an I2C write transaction by the MSS I2C slave. It is your responsibility to
    create and register the implementation of this handler function that will
    process or trigger the processing of the received data.
  Transaction Types
    The MSS I2C driver is designed to handle three types of I2C transaction:
      • Write transactions
      • Read transactions
      • Write-read transactions

    Write transaction
      The master I2C device initiates a write transaction by sending a START bit
      as soon as the bus becomes free. The START bit is followed by the 7-bit
      serial address of the target slave device followed by the read/write bit
      indicating the direction of the transaction. The slave acknowledges receipt
      of it’s address with an acknowledge bit. The master sends data one byte at
      a time to the slave, which must acknowledge receipt of each byte for the
      next byte to be sent. The master sends a STOP bit to complete the transaction.
      The slave can abort the transaction by replying with a non-acknowledge bit
      instead of an acknowledge.
      The application programmer can choose not to send a STOP bit at the end of
      the transaction causing the next transaction to begin with a repeated START bit.

    Read transaction
      The master I2C device initiates a read transaction by sending a START bit
      as soon as the bus becomes free. The START bit is followed by the 7-bit
      serial address of the target slave device followed by the read/write bit
      indicating the direction of the transaction. The slave acknowledges receipt
      of it’s slave address with an acknowledge bit. The slave sends data one byte
      at a time to the master, which must acknowledge receipt of each byte for the
      next byte to be sent. The master sends a non-acknowledge bit following the
      last byte it wishes to read followed by a STOP bit.
      The application programmer can choose not to send a STOP bit at the end of
      the transaction causing the next transaction to begin with a repeated START bit.

    Write-read transaction
      The write-read transaction is a combination of a write transaction
      immediately followed by a read transaction. There is no STOP bit between
      the write and read phases of a write-read transaction. A repeated START
      bit is sent between the write and read phases.
      The write-read transaction is typically used to send a command or offset
      in the write transaction specifying the logical data to be transferred
      during the read phase.
      The application programmer can choose not to send a STOP bit at the end of
      the transaction causing the next transaction to begin with a repeated START bit.

  Master Operations
    The application can use the MSS_I2C_write(), MSS_I2C_read() and MSS_I2C_write_read()
    functions to initiate an I2C bus transaction. The application can then wait
    for the transaction to complete using the MSS_I2C_wait_complete() function
    or poll the status of the I2C transaction using the MSS_I2C_get_status()
    function until it returns a value different from MSS_I2C_IN_PROGRESS.

  Slave Operations
    The configuration of the MSS I2C driver to operate as an I2C slave requires
    the use of the following functions:
      • MSS_I2C_set_slave_tx_buffer()
      • MSS_I2C_set_slave_rx_buffer()
      • MSS_I2C_set_slave_mem_offset_length()
      • MSS_I2C_register_write_handler()
      • MSS_I2C_enable_slave_rx()
    Use of all functions is not required if the slave I2C does not need to support
    all types of I2C read transactions. The subsequent sections list the functions
    that must be used to support each transaction type.

    Responding to read transactions
      The following functions are used to configure the MSS I2C driver to respond
      to I2C read transactions:
        • MSS_I2C_set_slave_tx_buffer()
        • MSS_I2C_enable_slave_rx()
      The function MSS_I2C_set_slave_tx_buffer() specifies the data buffer that
      will be transmitted when the I2C slave is the target of an I2C read
      transaction. It is then up to the application to manage the content of that
      buffer to control the data that will be transmitted to the I2C master as a
      result of the read transaction.
      The function MSS_I2C_enable_slave_rx() enables the MSS I2C hardware instance
      to respond to I2C transactions. It must be called after the MSS I2C driver
      has been configured to respond to the required transaction types.

    Responding to write transactions
      The following functions are used to configure the MSS I2C driver to respond
      to I2C write transactions:
        • MSS_I2C_set_slave_rx_buffer()
        • MSS_I2C_register_write_handler()
        • MSS_I2C_enable_slave_rx()
      The function MSS_I2C_set_slave_rx_buffer() specifies the data buffer that
      will be used to store the data received by the I2C slave when it is the
      target an I2C  write transaction.
      The function MSS_I2C_register_write_handler() specifies the handler function
      that must be called on completion of the I2C write transaction. It is this
      handler function that will process or trigger the processing of the received
      data.
      The function MSS_I2C_enable_slave_rx() enables the MSS I2C hardware instance
      to respond to I2C transactions. It must be called after the MSS I2C driver
      has been configured to respond to the required transaction types.

    Responding to write-read transactions
      The following functions are used to configure the MSS I2C driver to respond
      to write-read transactions:
        • MSS_I2C_set_slave_tx_buffer()
        • MSS_I2C_set_slave_rx_buffer()
        • MSS_I2C_set_slave_mem_offset_length()
        • MSS_I2C_enable_slave_rx()
      The function MSS_I2C_set_slave_mem_offset_length() specifies the number of
      bytes expected by the I2C slave during the write phase of the write-read
      transaction.
      The function MSS_I2C_set_slave_tx_buffer() specifies the data that will be
      transmitted to the I2C master during the read phase of the write-read
      transaction. The value received by the I2C slave during the write phase of
      the transaction will be used as an index into the transmit buffer specified
      by this function to decide which part of the transmit buffer will be
      transmitted to the I2C master as part of the read phase of the write-read
      transaction.
      The function MSS_I2C_set_slave_rx_buffer() specifies the data buffer that
      will be used to store the data received by the I2C slave during the write
      phase of the write-read transaction. This buffer must be at least large
      enough to accommodate the number of bytes specified through the
      MSS_I2C_set_slave_mem_offset_length() function.
      The function MSS_I2C_enable_slave_rx() enables the MSS I2C hardware
      instance to respond to I2C transactions. It must be called after the MSS
      I2C driver has been configured to respond to the required transaction types.
 *//*=========================================================================*/
#ifndef I2C_H_
#define I2C_H_

#include "../../CMSIS/a2fxxxm3.h"

/* FreeRTOS includes. */
#include "FreeRTOS.h"
#include "task.h"
#include "semphr.h"

#ifdef __cplusplus
extern "C" {
#endif

/*-------------------------------------------------------------------------*//**
  The mss_i2c_clock_divider_t type is used to specify the divider to be applied
  to the MSS I2C BCLK signal in order to generate the I2C clock.
 */
typedef enum mss_i2c_clock_divider {
    MSS_I2C_PCLK_DIV_256 = 0,
    MSS_I2C_PCLK_DIV_224,
    MSS_I2C_PCLK_DIV_192,
    MSS_I2C_PCLK_DIV_160,
    MSS_I2C_PCLK_DIV_960,
    MSS_I2C_PCLK_DIV_120,
    MSS_I2C_PCLK_DIV_60,
    MSS_I2C_BCLK_DIV_8
} mss_i2c_clock_divider_t;

/*-------------------------------------------------------------------------*//**
  The MSS_I2C_RELEASE_BUS constant is used to specify the options parameter to
  functions MSS_I2C_read(), MSS_I2C_write() and MSS_I2C_write_read() to indicate
  that a STOP bit must be generated at the end of the I2C transaction to release
  the bus.
 */
#define MSS_I2C_RELEASE_BUS     0x00

/*-------------------------------------------------------------------------*//**
  The MSS_I2C_HOLD_BUS constant is used to specify the options parameter to
  functions MSS_I2C_read(), MSS_I2C_write() and MSS_I2C_write_read() to indicate
  that a STOP bit must not be generated at the end of the I2C transaction in
  order to retain the bus ownership. This will cause the next transaction to
  begin with a repeated START bit and no STOP bit between the transactions.
 */
#define MSS_I2C_HOLD_BUS        0x01

/*-------------------------------------------------------------------------*//**
  The mss_i2c_status_t type is used to report the status of I2C transactions.
 */
typedef enum mss_i2c_status
{
    MSS_I2C_SUCCESS = 0,
    MSS_I2C_IN_PROGRESS,
    MSS_I2C_FAILED
} mss_i2c_status_t;

/*-------------------------------------------------------------------------*//**
  The mss_i2c_slave_handler_ret_t type is used by slave write handler functions
  to indicate whether the received data buffer should be released or not.
 */
typedef enum mss_i2c_slave_handler_ret {
    MSS_I2C_REENABLE_SLAVE_RX = 0,
    MSS_I2C_PAUSE_SLAVE_RX = 1
} mss_i2c_slave_handler_ret_t;

/*-------------------------------------------------------------------------*//**
  Slave write handler functions prototype.
  ------------------------------------------------------------------------------
  This defines the function prototype that must be followed by MSS I2C slave
  write handler functions. These functions are registered with the MSS I2C driver
  through the MSS_I2C_register_write_handler() function.

  Declaring and Implementing Slave Write Handler Functions:
    Slave write handler functions should follow the following prototype:
    mss_i2c_slave_handler_ret_t write_handler( uint8_t * data, uint16_t size );

    The data parameter is a pointer to a buffer (received data buffer) holding
    the data written to the MSS I2C slave.
    The size parameter is the number of bytes held in the received data buffer.
    Handler functions must return one of the following values:
        • MSS_I2C_REENABLE_SLAVE_RX
        • MSS_I2C_PAUSE_SLAVE_RX.
    If the handler function returns MSS_I2C_REENABLE_SLAVE_RX, the driver will
    release the received data buffer and allow further I2C write transactions to
    the MSS I2C slave to take place.
    If the handler function returns MSS_I2C_PAUSE_SLAVE_RX, the MSS I2C slave
    will respond to subsequent write requests with a non-acknowledge bit (NACK),
    until the received data buffer content has been processed by some other part
    of the software application.
    A call to MSS_I2C_enable_slave_rx() is required at some point after
    returning MSS_I2C_PAUSE_SLAVE_RX in order to release the received data
    buffer so it can be used to store data received by subsequent I2C write
    transactions.
 */
typedef mss_i2c_slave_handler_ret_t (*mss_i2c_slave_wr_handler_t)( uint8_t *, uint16_t );

/*-------------------------------------------------------------------------*//**
  mss_i2c_instance_t
  ------------------------------------------------------------------------------
  There is one instance of this structure for each of the microcontroller
  subsystem's I2Cs. Instances of this structure are used to identify a specific
  I2C. A pointer to an instance of the mss_i2c_instance_t structure is passed as
  the first parameter to MSS I2C driver functions to identify which I2C should
  perform the requested operation.
 */
typedef struct mss_i2c_instance
{
	uint_fast8_t ser_address;
	/* Transmit related info:*/
	uint_fast8_t target_addr;

	/* Current transaction type (WRITE, READ, RANDOM_READ)*/
	uint8_t transaction;

	uint_fast16_t random_read_addr;

    uint8_t options;

	/* I2C hardware instance identification */
    IRQn_Type  irqn;
    I2C_TypeDef * hw_reg;
    I2C_BitBand_TypeDef * hw_reg_bit;

	/* TX INFO: */
	const uint8_t * tx_buffer;
	uint_fast16_t tx_size;
	uint_fast16_t tx_idx;
	uint_fast8_t dir;

	/* RX INFO: */
	uint8_t * rx_buffer;
	uint_fast16_t rx_size;
	uint_fast16_t rx_idx;

	/* status variable: */
    volatile mss_i2c_status_t status;

	/* Slave data: */
	uint_fast8_t slave_mem_offset_length;
	mss_i2c_slave_wr_handler_t slave_write_handler;
	
	/* Used to get access to and wait for completion of an I2C transaction. */
	SemaphoreHandle_t xI2CCompleteSemaphore;
	
} mss_i2c_instance_t;

/*-------------------------------------------------------------------------*//**
  This instance of mss_i2c_instance_t holds all data related to the operations
  performed by MSS I2C 0. A pointer to g_mss_i2c0 is passed as the first
  parameter to MSS I2C driver functions to indicate that MSS I2C 0 should
  perform the requested operation.
 */
extern mss_i2c_instance_t g_mss_i2c0;

/*-------------------------------------------------------------------------*//**
  This instance of mss_i2c_instance_t holds all data related to the operations
  performed by MSS I2C 1. A pointer to g_mss_i2c1 is passed as the first
  parameter to MSS I2C driver functions to indicate that MSS I2C 1 should
  perform the requested operation.
 */
extern mss_i2c_instance_t g_mss_i2c1;

/*-------------------------------------------------------------------------*//**
  MSS I2C initialisation routine.
  ------------------------------------------------------------------------------
  The MSS_I2C_init() function initializes and configures hardware and data
  structures of one of the SmartFusion MSS I2Cs.
  ------------------------------------------------------------------------------
  @param this_i2c:
    The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block to be initialized. There are two such
    data structures, g_mss_i2c0 and g_mss_i2c1, associated with MSS I2C 0 and
    MSS I2C 1 respectively. This parameter must point to either the g_mss_i2c0
    or g_mss_i2c1 global data structure defined within the I2C driver.

  @param ser_address:
    This parameter sets the I2C serial address being initialized. It is the I2C
    bus address to which the MSS I2C instance will respond. Any 8 bit address is
    allowed.

  @param ser_clock_speed:
    This parameter sets the I2C serial clock frequency. It selects the divider
    that will be used to generate the serial clock from the APB clock. It can be
    one of the following:
        • MSS_I2C_PCLK_DIV_256
        • MSS_I2C_PCLK_DIV_224
        • MSS_I2C_PCLK_DIV_192
        • MSS_I2C_PCLK_DIV_160
        • MSS_I2C_PCLK_DIV_960
        • MSS_I2C_PCLK_DIV_120
        • MSS_I2C_PCLK_DIV_60
        • MSS_I2C_BCLK_DIV_8
 */
void MSS_I2C_init
(
	mss_i2c_instance_t * this_i2c,
	uint8_t ser_address,
	mss_i2c_clock_divider_t ser_clock_speed
);

/*******************************************************************************
 *******************************************************************************
 *
 *                           Master specific functions
 *
 * The following functions are only used within an I2C master's implementation.
 */

/*-------------------------------------------------------------------------*//**
  I2C master write function.
  ------------------------------------------------------------------------------
  This function initiates an I2C master write transaction. This function returns
  immediately after initiating the transaction. The content of the write buffer
  passed as parameter should not be modified until the write transaction
  completes. It also means that the memory allocated for the write buffer should
  not be freed or go out of scope before the write completes. You can check for
  the write transaction completion using the MSS_I2C_status() function.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param serial_addr:
  	This parameter specifies the serial address of the target I2C device.

  @param write_buffer:
  	This parameter is a pointer to a buffer holding the data to be written to
    the target I2C device.
    Care must be taken not to release the memory used by this buffer before the
    write transaction completes. For example, it is not appropriate to return
    from a function allocating this buffer as an array variable before the write
    transaction completes as this would result in the buffer's memory being
    de-allocated from the stack when the function returns. This memory could
    then be subsequently reused and modified causing unexpected data to be
    written to the target I2C device.

  @param write_size:
  	Number of bytes held in the write_buffer to be written to the target I2C
    device.

 @param options:
 	The options parameter is used to indicate if the I2C bus should be released
    on completion of the write transaction. Using the MSS_I2C_RELEASE_BUS
    constant for the options parameter causes a STOP bit to be generated at the
    end of the write transaction causing the bus to be released for other I2C
    devices to use. Using the MSS_I2C_HOLD_BUS constant as options parameter
    prevents a STOP bit from being generated at the end of the write
    transaction, preventing other I2C devices from initiating a bus transaction.
 */
void MSS_I2C_write
(
	mss_i2c_instance_t * this_i2c,
	uint8_t serial_addr,
	const uint8_t * write_buffer,
	uint16_t write_size,
    uint8_t options
);

/*-------------------------------------------------------------------------*//**
  I2C master read.
  ------------------------------------------------------------------------------
  This function initiates an I2C master read transaction. This function returns
  immediately after initiating the transaction.
  The content of the read buffer passed as parameter should not be modified
  until the read transaction completes. It also means that the memory allocated
  for the read buffer should not be freed or go out of scope before the read
  completes. You can check for the read transaction completion using the
  MSS_I2C_status() function.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param serial_addr:
  	This parameter specifies the serial address of the target I2C device.

  @param read_buffer
  	Pointer to a buffer where the data received from the target device will be
    stored.
    Care must be taken not to release the memory used by this buffer before the
    read transaction completes. For example, it is not appropriate to return
    from a function allocating this buffer as an array variable before the read
    transaction completes as this would result in the buffer's memory being
    de-allocated from the stack when the function returns. This memory could
    then be subsequently reallocated resulting in the read transaction
    corrupting the newly allocated memory.

  @param read_size:
  	This parameter is the number of bytes to read from the target device. This
    size must not exceed the size of the read_buffer buffer.

  @param options:
 	The options parameter is used to indicate if the I2C bus should be released
    on completion of the read transaction. Using the MSS_I2C_RELEASE_BUS
    constant for the options parameter causes a STOP bit to be generated at the
    end of the read transaction causing the bus to be released for other I2C
    devices to use. Using the MSS_I2C_HOLD_BUS constant as options parameter
    prevents a STOP bit from being generated at the end of the read transaction,
    preventing other I2C devices from initiating a bus transaction.
 */
void MSS_I2C_read
(
	mss_i2c_instance_t * this_i2c,
	uint8_t serial_addr,
	uint8_t * read_buffer,
	uint16_t read_size,
    uint8_t options
);

/*-------------------------------------------------------------------------*//**
  I2C master write-read
  ------------------------------------------------------------------------------
  This function initiates an I2C write-read transaction where data is first
  written to the target device before issuing a restart condition and changing
  the direction of the I2C transaction in order to read from the target device.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param serial_addr:
  	This parameter specifies the serial address of the target I2C device.

  @param addr_offset:
  	This parameter is a pointer to the buffer containing the data that will be
    sent to the slave during the write phase of the write-read transaction. This
    data is typically used to specify an address offset specifying to the I2C
    slave device what data it must return during the read phase of the
    write-read transaction.

  @param offset_size:
  	This parameter specifies the number of offset bytes to be written during the
    write phase of the write-read transaction. This is typically the size of the
    buffer pointed to by the addr_offset parameter.

  @param read_buffer:
  	This parameter is a pointer to the buffer where the data read from the I2C
    slave will be stored.

  @param read_size:
  	This parameter specifies the number of bytes to read from the target I2C
    slave device. This size must not exceed the size of the buffer pointed to by
    the read_buffer parameter.

  @param options:
 	The options parameter is used to indicate if the I2C bus should be released
    on completion of the write-read transaction. Using the MSS_I2C_RELEASE_BUS
    constant for the options parameter causes a STOP bit to be generated at the
    end of the write-read transaction causing the bus to be released for other
    I2C devices to use. Using the MSS_I2C_HOLD_BUS constant as options parameter
    prevents a STOP bit from being generated at the end of the write-read
    transaction, preventing other I2C devices from initiating a bus transaction.
 */
void MSS_I2C_write_read
(
	mss_i2c_instance_t * this_i2c,
	uint8_t serial_addr,
	const uint8_t * addr_offset,
	uint16_t offset_size,
	uint8_t * read_buffer,
	uint16_t read_size,
    uint8_t options
);

/*-------------------------------------------------------------------------*//**
  I2C status
  ------------------------------------------------------------------------------
  This function indicates the current state of a MSS I2C instance.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.
  ------------------------------------------------------------------------------
  @return
    The return value indicates the current state of a MSS I2C instance or the
    outcome of the previous transaction if no transaction is in progress.
    Possible return values are:
      SUCCESS
        The last I2C transaction has completed successfully.
      IN_PROGRESS
        There is an I2C transaction in progress.
      FAILED
        The last I2C transaction failed.

 */
mss_i2c_status_t MSS_I2C_get_status
(
    mss_i2c_instance_t * this_i2c
);

/*-------------------------------------------------------------------------*//**
  Wait for I2C transaction completion.
  ------------------------------------------------------------------------------
  This function waits for the current I2C transaction to complete. The return
  value indicates whether the last I2C transaction was successful, or is still
  in progress, or failed.
  ------------------------------------------------------------------------------
  @param this_i2c:
    The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.
  ------------------------------------------------------------------------------
  @return
    The return value indicates the outcome of the last I2C transaction. It can
    be one of the following:
      MSS_I2C_SUCCESS
        The last I2C transaction has completed successfully.
      MSS_I2C_IN_PROGRESS
        The current I2C transaction is still in progress.
      MSS_I2C_FAILED
        The last I2C transaction failed.
 */
mss_i2c_status_t MSS_I2C_wait_complete
(
    mss_i2c_instance_t * this_i2c
);


/*******************************************************************************
 *******************************************************************************
 *
 *                           Slave specific functions
 *
 * The following functions are only used within the implementation of an I2C
 * slave device.
 */

/*-------------------------------------------------------------------------*//**
  I2C slave transmit buffer configuration.
  ------------------------------------------------------------------------------
  This function specifies the memory buffer holding the data that will be sent
  to the I2C master when this MSS I2C instance is the target of an I2C read or
  write-read transaction.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param tx_buffer:
  	This parameter is a pointer to the memory buffer holding the data to be
    returned to the I2C master when this MSS I2C instance is the target of an
    I2C read or write-read transaction.

  @param tx_size:
  	Size of the transmit buffer pointed to by the tx_buffer parameter.
 */
void MSS_I2C_set_slave_tx_buffer
(
	mss_i2c_instance_t * this_i2c,
	uint8_t * tx_buffer,
	uint16_t tx_size
);

/*-------------------------------------------------------------------------*//**
  I2C slave receive buffer configuration.
  ------------------------------------------------------------------------------
  This function specifies the memory buffer that will be used by the MSS I2C
  instance to receive data when it is a slave. This buffer is the memory where
  data will be stored when the MSS I2C is the target of an I2C master write
  transaction (i.e. when it is the slave).
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param rx_buffer:
  	This parameter is a pointer to the memory buffer allocated by the caller
    software to be used as a slave receive buffer.

  @param rx_size:
  	Size of the slave receive buffer. This is the amount of memory that is
    allocated to the buffer pointed to by rx_buffer.
    Note:   This buffer size will indirectly specify the maximum I2C write
            transaction length this MSS I2C instance can be the target of. This
            is because this MSS I2C instance will respond to further received
            bytes with a non-acknowledge bit (NACK) as soon as its receive
            buffer is full. This will cause the write transaction to fail.
 */
void MSS_I2C_set_slave_rx_buffer
(
	mss_i2c_instance_t * this_i2c,
	uint8_t * rx_buffer,
	uint16_t rx_size
);

/*-------------------------------------------------------------------------*//**
  I2C slave memory offset length configuration.
  ------------------------------------------------------------------------------
  This function is used as part of the configuration of a MSS I2C instance for
  operation as a slave supporting write-read transactions. It specifies the
  number of bytes expected as part of the write phase of a write-read
  transaction. The bytes received during the write phase of a write-read
  transaction will be interpreted as an offset into the slave’s transmit buffer.
  This allows random access into the I2C slave transmit buffer from a remote
  I2C master.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param offset_length:
  	The offset_length parameter configures the number of bytes to be interpreted
    by the MSS I2C slave as a memory offset value during the write phase of
    write-read transactions.
 */
void MSS_I2C_set_slave_mem_offset_length
(
	mss_i2c_instance_t * this_i2c,
	uint8_t offset_length
);

/*-------------------------------------------------------------------------*//**
  I2C write handler registration.
  ------------------------------------------------------------------------------
  Register the function that will be called to process the data written to this
  MSS I2C instance when it is the slave in an I2C write transaction.
  Note: The write handler is not called as a result of a write-read transaction.
        The write data of a write read transaction is interpreted as an offset
        into the slave’s transmit buffer and handled by the driver.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.

  @param handler:
  	Pointer to the function that will process the I2C write request.
 */
void MSS_I2C_register_write_handler
(
	mss_i2c_instance_t * this_i2c,
	mss_i2c_slave_wr_handler_t handler
);

/*-------------------------------------------------------------------------*//**
  I2C slave receive enable.
  ------------------------------------------------------------------------------
  Enables the MSS I2C instance identified through the this_i2c parameter to
  receive data when it is the target of an I2C write or write-read transaction.
  ------------------------------------------------------------------------------
  @param this_i2c:
  	The this_i2c parameter is a pointer to an mss_i2c_instance_t structure
    identifying the MSS I2C hardware block that will perform the requested
    function. There are two such data structures, g_mss_i2c0 and g_mss_i2c1,
    associated with MSS I2C 0 and MSS I2C 1 respectively. This parameter must
    point to either the g_mss_i2c0 or g_mss_i2c1 global data structure defined
    within the I2C driver.
 */
void MSS_I2C_enable_slave_rx
(
	mss_i2c_instance_t * this_i2c
);

#ifdef __cplusplus
}
#endif

#endif /*MSS_I2C_H_*/