| /** | |
| * \file | |
| * | |
| * \brief Board configuration. | |
| * | |
| * Copyright (c) 2011 - 2012 Atmel Corporation. All rights reserved. | |
| * | |
| * \asf_license_start | |
| * | |
| * \page License | |
| * | |
| * Redistribution and use in source and binary forms, with or without | |
| * modification, are permitted provided that the following conditions are met: | |
| * | |
| * 1. Redistributions of source code must retain the above copyright notice, | |
| * this list of conditions and the following disclaimer. | |
| * | |
| * 2. Redistributions in binary form must reproduce the above copyright notice, | |
| * this list of conditions and the following disclaimer in the documentation | |
| * and/or other materials provided with the distribution. | |
| * | |
| * 3. The name of Atmel may not be used to endorse or promote products derived | |
| * from this software without specific prior written permission. | |
| * | |
| * 4. This software may only be redistributed and used in connection with an | |
| * Atmel microcontroller product. | |
| * | |
| * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED | |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE | |
| * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR | |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS | |
| * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) | |
| * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, | |
| * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN | |
| * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE | |
| * POSSIBILITY OF SUCH DAMAGE. | |
| * | |
| * \asf_license_stop | |
| * | |
| */ | |
| #ifndef CONF_BOARD_H_INCLUDED | |
| #define CONF_BOARD_H_INCLUDED | |
| /* Configure UART pins */ | |
| //#define CONF_BOARD_UART_CONSOLE | |
| /* Configure ADC example pins */ | |
| //#define CONF_BOARD_ADC | |
| /* Enable USB interface (USB) for host mode */ | |
| //#define CONF_BOARD_USB_PORT | |
| /* | |
| * LED pins are not configured for PWM function here. | |
| * Because those LED pins are enabled for PIO function by default. | |
| * You can enable them according to application. | |
| */ | |
| /* Configure PWM LED0 pin */ | |
| //#define CONF_BOARD_PWM_LED0 | |
| /* Configure PWM LED1 pin */ | |
| //#define CONF_BOARD_PWM_LED1 | |
| /* Configure PWM LED2 pin */ | |
| //#define CONF_BOARD_PWM_LED2 | |
| /* Configure SPI0 pins */ | |
| //#define CONF_BOARD_SPI0 | |
| //#define CONF_BOARD_SPI0_NPCS0 | |
| //#define CONF_BOARD_SPI0_NPCS1 | |
| //#define CONF_BOARD_SPI0_NPCS2 | |
| //#define CONF_BOARD_SPI0_NPCS3 | |
| /* Configure SPI1 pins */ | |
| //#define CONF_BOARD_SPI1 | |
| //#define CONF_BOARD_SPI1_NPCS0 | |
| //#define CONF_BOARD_SPI1_NPCS1 | |
| //#define CONF_BOARD_SPI1_NPCS2 | |
| //#define CONF_BOARD_SPI1_NPCS3 | |
| //#define CONF_BOARD_TWI0 | |
| //#define CONF_BOARD_TWI1 | |
| /* | |
| * USART pins are configured as basic serial port by default. | |
| * You can enable other pins according application. | |
| */ | |
| /* Configure USART RXD pin */ | |
| #define CONF_BOARD_USART_RXD | |
| /* Configure USART TXD pin */ | |
| #define CONF_BOARD_USART_TXD | |
| /* Configure USART CTS pin */ | |
| //#define CONF_BOARD_USART_CTS | |
| /* Configure USART RTS pin */ | |
| //#define CONF_BOARD_USART_RTS | |
| /* Configure USART synchronous communication SCK pin */ | |
| //#define CONF_BOARD_USART_SCK | |
| /* Configure ADM3312 enable pin */ | |
| #define CONF_BOARD_ADM3312_EN | |
| /* Configure IrDA transceiver shutdown pin */ | |
| //#define CONF_BOARD_TFDU4300_SD | |
| /* Configure RS485 transceiver ADM3485 RE pin */ | |
| //#define CONF_BOARD_ADM3485_RE | |
| //#define CONF_BOARD_SMC_PSRAM | |
| /* Configure LCD EBI pins */ | |
| //#define CONF_BOARD_HX8347A | |
| /* Configure Backlight control pin */ | |
| //#define CONF_BOARD_AAT3194 | |
| #endif /* CONF_BOARD_H_INCLUDED */ |