//***************************************************************************** | |
// | |
// hw_gpio.h - Defines and Macros for GPIO hardware. | |
// | |
// Copyright (c) 2005,2006 Luminary Micro, Inc. All rights reserved. | |
// | |
// Software License Agreement | |
// | |
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and | |
// exclusively on LMI's Stellaris Family of microcontroller products. | |
// | |
// The software is owned by LMI and/or its suppliers, and is protected under | |
// applicable copyright laws. All rights are reserved. Any use in violation | |
// of the foregoing restrictions may subject the user to criminal sanctions | |
// under applicable laws, as well as to civil liability for the breach of the | |
// terms and conditions of this license. | |
// | |
// THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED | |
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF | |
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. | |
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR | |
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. | |
// | |
// This is part of revision 635 of the Stellaris Driver Library. | |
// | |
//***************************************************************************** | |
#ifndef __HW_GPIO_H__ | |
#define __HW_GPIO_H__ | |
//***************************************************************************** | |
// | |
// GPIO Register Offsets. | |
// | |
//***************************************************************************** | |
#define GPIO_O_DATA 0x00000000 // Data register. | |
#define GPIO_O_DIR 0x00000400 // Data direction register. | |
#define GPIO_O_IS 0x00000404 // Interrupt sense register. | |
#define GPIO_O_IBE 0x00000408 // Interrupt both edges register. | |
#define GPIO_O_IEV 0x0000040C // Intterupt event register. | |
#define GPIO_O_IM 0x00000410 // Interrupt mask register. | |
#define GPIO_O_RIS 0x00000414 // Raw interrupt status register. | |
#define GPIO_O_MIS 0x00000418 // Masked interrupt status reg. | |
#define GPIO_O_ICR 0x0000041C // Interrupt clear register. | |
#define GPIO_O_AFSEL 0x00000420 // Mode control select register. | |
#define GPIO_O_DR2R 0x00000500 // 2ma drive select register. | |
#define GPIO_O_DR4R 0x00000504 // 4ma drive select register. | |
#define GPIO_O_DR8R 0x00000508 // 8ma drive select register. | |
#define GPIO_O_ODR 0x0000050C // Open drain select register. | |
#define GPIO_O_PUR 0x00000510 // Pull up select register. | |
#define GPIO_O_PDR 0x00000514 // Pull down select register. | |
#define GPIO_O_SLR 0x00000518 // Slew rate control enable reg. | |
#define GPIO_O_DEN 0x0000051C // Digital input enable register. | |
#define GPIO_O_PeriphID4 0x00000FD0 // | |
#define GPIO_O_PeriphID5 0x00000FD4 // | |
#define GPIO_O_PeriphID6 0x00000FD8 // | |
#define GPIO_O_PeriphID7 0x00000FDC // | |
#define GPIO_O_PeriphID0 0x00000FE0 // | |
#define GPIO_O_PeriphID1 0x00000FE4 // | |
#define GPIO_O_PeriphID2 0x00000FE8 // | |
#define GPIO_O_PeriphID3 0x00000FEC // | |
#define GPIO_O_PCellID0 0x00000FF0 // | |
#define GPIO_O_PCellID1 0x00000FF4 // | |
#define GPIO_O_PCellID2 0x00000FF8 // | |
#define GPIO_O_PCellID3 0x00000FFC // | |
//***************************************************************************** | |
// | |
// GPIO Register reset values. | |
// | |
//***************************************************************************** | |
#define GPIO_RV_DATA 0x00000000 // Data register reset value. | |
#define GPIO_RV_DIR 0x00000000 // Data direction reg RV. | |
#define GPIO_RV_IS 0x00000000 // Interrupt sense reg RV. | |
#define GPIO_RV_IBE 0x00000000 // Interrupt both edges reg RV. | |
#define GPIO_RV_IEV 0x00000000 // Intterupt event reg RV. | |
#define GPIO_RV_IM 0x00000000 // Interrupt mask reg RV. | |
#define GPIO_RV_RIS 0x00000000 // Raw interrupt status reg RV. | |
#define GPIO_RV_MIS 0x00000000 // Masked interrupt status reg RV. | |
#define GPIO_RV_IC 0x00000000 // Interrupt clear reg RV. | |
#define GPIO_RV_AFSEL 0x00000000 // Mode control select reg RV. | |
#define GPIO_RV_DR2R 0x000000FF // 2ma drive select reg RV. | |
#define GPIO_RV_DR4R 0x00000000 // 4ma drive select reg RV. | |
#define GPIO_RV_DR8R 0x00000000 // 8ma drive select reg RV. | |
#define GPIO_RV_ODR 0x00000000 // Open drain select reg RV. | |
#define GPIO_RV_PUR 0x000000FF // Pull up select reg RV. | |
#define GPIO_RV_PDR 0x00000000 // Pull down select reg RV. | |
#define GPIO_RV_SLR 0x00000000 // Slew rate control enable reg RV. | |
#define GPIO_RV_DEN 0x000000FF // Digital input enable reg RV. | |
#define GPIO_RV_PeriphID4 0x00000000 // | |
#define GPIO_RV_PeriphID5 0x00000000 // | |
#define GPIO_RV_PeriphID6 0x00000000 // | |
#define GPIO_RV_PeriphID7 0x00000000 // | |
#define GPIO_RV_PeriphID0 0x00000061 // | |
#define GPIO_RV_PeriphID1 0x00000010 // | |
#define GPIO_RV_PeriphID2 0x00000004 // | |
#define GPIO_RV_PeriphID3 0x00000000 // | |
#define GPIO_RV_PCellID0 0x0000000D // | |
#define GPIO_RV_PCellID1 0x000000F0 // | |
#define GPIO_RV_PCellID2 0x00000005 // | |
#define GPIO_RV_PCellID3 0x000000B1 // | |
#endif // __HW_GPIO_H__ |