//***************************************************************************** | |
// | |
// hw_sysctl.h - Macros used when accessing the system control hardware. | |
// | |
// Copyright (c) 2005,2006 Luminary Micro, Inc. All rights reserved. | |
// | |
// Software License Agreement | |
// | |
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and | |
// exclusively on LMI's Stellaris Family of microcontroller products. | |
// | |
// The software is owned by LMI and/or its suppliers, and is protected under | |
// applicable copyright laws. All rights are reserved. Any use in violation | |
// of the foregoing restrictions may subject the user to criminal sanctions | |
// under applicable laws, as well as to civil liability for the breach of the | |
// terms and conditions of this license. | |
// | |
// THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED | |
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF | |
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. | |
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR | |
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. | |
// | |
// This is part of revision 635 of the Stellaris Driver Library. | |
// | |
//***************************************************************************** | |
#ifndef __HW_SYSCTL_H__ | |
#define __HW_SYSCTL_H__ | |
//***************************************************************************** | |
// | |
// The following define the offsets of the system control registers. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DID0 0x400fe000 // Device identification register 0 | |
#define SYSCTL_DID1 0x400fe004 // Device identification register 1 | |
#define SYSCTL_DC0 0x400fe008 // Device capabilities register 0 | |
#define SYSCTL_DC1 0x400fe010 // Device capabilities register 1 | |
#define SYSCTL_DC2 0x400fe014 // Device capabilities register 2 | |
#define SYSCTL_DC3 0x400fe018 // Device capabilities register 3 | |
#define SYSCTL_DC4 0x400fe01C // Device capabilities register 4 | |
#define SYSCTL_PBORCTL 0x400fe030 // POR/BOR reset control register | |
#define SYSCTL_LDOPCTL 0x400fe034 // LDO power control register | |
#define SYSCTL_SRCR0 0x400fe040 // Software reset control reg 0 | |
#define SYSCTL_SRCR1 0x400fe044 // Software reset control reg 1 | |
#define SYSCTL_SRCR2 0x400fe048 // Software reset control reg 2 | |
#define SYSCTL_RIS 0x400fe050 // Raw interrupt status register | |
#define SYSCTL_IMC 0x400fe054 // Interrupt mask/control register | |
#define SYSCTL_MISC 0x400fe058 // Interrupt status register | |
#define SYSCTL_RESC 0x400fe05c // Reset cause register | |
#define SYSCTL_RCC 0x400fe060 // Run-mode clock config register | |
#define SYSCTL_PLLCFG 0x400fe064 // PLL configuration register | |
#define SYSCTL_RCGC0 0x400fe100 // Run-mode clock gating register 0 | |
#define SYSCTL_RCGC1 0x400fe104 // Run-mode clock gating register 1 | |
#define SYSCTL_RCGC2 0x400fe108 // Run-mode clock gating register 2 | |
#define SYSCTL_SCGC0 0x400fe110 // Sleep-mode clock gating reg 0 | |
#define SYSCTL_SCGC1 0x400fe114 // Sleep-mode clock gating reg 1 | |
#define SYSCTL_SCGC2 0x400fe118 // Sleep-mode clock gating reg 2 | |
#define SYSCTL_DCGC0 0x400fe120 // Deep Sleep-mode clock gate reg 0 | |
#define SYSCTL_DCGC1 0x400fe124 // Deep Sleep-mode clock gate reg 1 | |
#define SYSCTL_DCGC2 0x400fe128 // Deep Sleep-mode clock gate reg 2 | |
#define SYSCTL_CLKVCLR 0x400fe150 // Clock verifcation clear register | |
#define SYSCTL_LDOARST 0x400fe160 // LDO reset control register | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DID0 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DID0_VER_MASK 0x70000000 // DID0 version mask | |
#define SYSCTL_DID0_VER_0 0x00000000 // DID0 version 0 | |
#define SYSCTL_DID0_MAJ_MASK 0x0000FF00 // Major revision mask | |
#define SYSCTL_DID0_MAJ_A 0x00000000 // Major revision A | |
#define SYSCTL_DID0_MAJ_B 0x00000100 // Major revision B | |
#define SYSCTL_DID0_MIN_MASK 0x000000FF // Minor revision mask | |
#define SYSCTL_DID0_MIN_0 0x00000000 // Minor revision 0 | |
#define SYSCTL_DID0_MIN_1 0x00000001 // Minor revision 1 | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DID1 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DID1_VER_MASK 0xF0000000 // Register version mask | |
#define SYSCTL_DID1_FAM_MASK 0x0F000000 // Family mask | |
#define SYSCTL_DID1_FAM_S 0x00000000 // Stellaris family | |
#define SYSCTL_DID1_PRTNO_MASK 0x00FF0000 // Part number mask | |
#define SYSCTL_DID1_PRTNO_101 0x00010000 // LM3S101 | |
#define SYSCTL_DID1_PRTNO_102 0x00020000 // LM3S102 | |
#define SYSCTL_DID1_PRTNO_301 0x00110000 // LM3S301 | |
#define SYSCTL_DID1_PRTNO_310 0x00120000 // LM3S310 | |
#define SYSCTL_DID1_PRTNO_315 0x00130000 // LM3S315 | |
#define SYSCTL_DID1_PRTNO_316 0x00140000 // LM3S316 | |
#define SYSCTL_DID1_TEMP_MASK 0x000000E0 // Temperature range mask | |
#define SYSCTL_DID1_TEMP_C 0x00000000 // Commercial temp range (0..70C) | |
#define SYSCTL_DID1_TEMP_I 0x00000020 // Industrial temp range (-40..85C) | |
#define SYSCTL_DID1_PKG_MASK 0x00000018 // Package mask | |
#define SYSCTL_DID1_PKG_28SOIC 0x00000000 // 28-pin SOIC | |
#define SYSCTL_DID1_PKG_48QFP 0x00000008 // 48-pin QFP | |
#define SYSCTL_DID1_ROHS 0x00000004 // Part is RoHS compliant | |
#define SYSCTL_DID1_QUAL_MASK 0x00000003 // Qualification status mask | |
#define SYSCTL_DID1_QUAL_ES 0x00000000 // Engineering sample (unqualified) | |
#define SYSCTL_DID1_QUAL_PP 0x00000001 // Pilot production (unqualified) | |
#define SYSCTL_DID1_QUAL_FQ 0x00000002 // Fully qualified | |
#define SYSCTL_DID1_PRTNO_SHIFT 16 | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DC0 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DC0_SRAMSZ_MASK 0xFFFF0000 // SRAM size mask | |
#define SYSCTL_DC0_SRAMSZ_2KB 0x00070000 // 2kB of SRAM | |
#define SYSCTL_DC0_SRAMSZ_4KB 0x000F0000 // 4kB of SRAM | |
#define SYSCTL_DC0_FLASHSZ_MASK 0x0000FFFF // Flash size mask | |
#define SYSCTL_DC0_FLASHSZ_8KB 0x00000003 // 8kB of flash | |
#define SYSCTL_DC0_FLASHSZ_16KB 0x00000007 // 16kB of flash | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DC1 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DC1_PWM 0x00100000 // PWM module present | |
#define SYSCTL_DC1_ADC 0x00010000 // ADC module present | |
#define SYSCTL_DC1_SYSDIV_MASK 0x0000F000 // Minimum system divider mask | |
#define SYSCTL_DC1_ADCSPD_MASK 0x00000F00 // ADC speed mask | |
#define SYSCTL_DC1_ADCSPD_250K 0x00000100 // 250Ksps ADC | |
#define SYSCTL_DC1_ADCSPD_125K 0x00000000 // 125Ksps ADC | |
#define SYSCTL_DC1_MPU 0x00000080 // Cortex-M3 MPU present | |
#define SYSCTL_DC1_TEMP 0x00000020 // Temperature sensor present | |
#define SYSCTL_DC1_PLL 0x00000010 // PLL present | |
#define SYSCTL_DC1_WDOG 0x00000008 // Watchdog present | |
#define SYSCTL_DC1_SWO 0x00000004 // Serial wire output present | |
#define SYSCTL_DC1_SWD 0x00000002 // Serial wire debug present | |
#define SYSCTL_DC1_JTAG 0x00000001 // JTAG debug present | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DC2 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DC2_COMP2 0x04000000 // Analog comparator 2 present | |
#define SYSCTL_DC2_COMP1 0x02000000 // Analog comparator 1 present | |
#define SYSCTL_DC2_COMP0 0x01000000 // Analog comparator 0 present | |
#define SYSCTL_DC2_TIMER2 0x00040000 // Timer 2 present | |
#define SYSCTL_DC2_TIMER1 0x00020000 // Timer 1 present | |
#define SYSCTL_DC2_TIMER0 0x00010000 // Timer 0 present | |
#define SYSCTL_DC2_I2C 0x00001000 // I2C present | |
#define SYSCTL_DC2_SSI 0x00000010 // SSI present | |
#define SYSCTL_DC2_UART1 0x00000002 // UART 1 present | |
#define SYSCTL_DC2_UART0 0x00000001 // UART 0 present | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DC3 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DC3_32KHZ 0x80000000 // 32kHz pin present | |
#define SYSCTL_DC3_CCP5 0x20000000 // CCP5 pin present | |
#define SYSCTL_DC3_CCP4 0x10000000 // CCP4 pin present | |
#define SYSCTL_DC3_CCP3 0x08000000 // CCP3 pin present | |
#define SYSCTL_DC3_CCP2 0x04000000 // CCP2 pin present | |
#define SYSCTL_DC3_CCP1 0x02000000 // CCP1 pin present | |
#define SYSCTL_DC3_CCP0 0x01000000 // CCP0 pin present | |
#define SYSCTL_DC3_ADC3 0x00080000 // ADC3 pin present | |
#define SYSCTL_DC3_ADC2 0x00040000 // ADC2 pin present | |
#define SYSCTL_DC3_ADC1 0x00020000 // ADC1 pin present | |
#define SYSCTL_DC3_ADC0 0x00010000 // ADC0 pin present | |
#define SYSCTL_DC3_C2O 0x00004000 // C2o pin present | |
#define SYSCTL_DC3_C2PLUS 0x00002000 // C2+ pin present | |
#define SYSCTL_DC3_C2MINUS 0x00001000 // C2- pin present | |
#define SYSCTL_DC3_C1O 0x00000800 // C1o pin present | |
#define SYSCTL_DC3_C1PLUS 0x00000400 // C1+ pin present | |
#define SYSCTL_DC3_C1MINUS 0x00000200 // C1- pin present | |
#define SYSCTL_DC3_C0O 0x00000100 // C0o pin present | |
#define SYSCTL_DC3_C0PLUS 0x00000080 // C0+ pin present | |
#define SYSCTL_DC3_C0MINUS 0x00000040 // C0- pin present | |
#define SYSCTL_DC3_PWM5 0x00000020 // PWM5 pin present | |
#define SYSCTL_DC3_PWM4 0x00000010 // PWM4 pin present | |
#define SYSCTL_DC3_PWM3 0x00000008 // PWM3 pin present | |
#define SYSCTL_DC3_PWM2 0x00000004 // PWM2 pin present | |
#define SYSCTL_DC3_PWM1 0x00000002 // PWM1 pin present | |
#define SYSCTL_DC3_PWM0 0x00000001 // PWM0 pin present | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_DC4 register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_DC4_GPIOE 0x00000010 // GPIO port E present | |
#define SYSCTL_DC4_GPIOD 0x00000008 // GPIO port D present | |
#define SYSCTL_DC4_GPIOC 0x00000004 // GPIO port C present | |
#define SYSCTL_DC4_GPIOB 0x00000002 // GPIO port B present | |
#define SYSCTL_DC4_GPIOA 0x00000001 // GPIO port A present | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_PBORCTL register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_PBORCTL_BOR_MASK 0x0000FFFC // BOR wait timer | |
#define SYSCTL_PBORCTL_BORIOR 0x00000002 // BOR interrupt or reset | |
#define SYSCTL_PBORCTL_BORWT 0x00000001 // BOR wait and check for noise | |
#define SYSCTL_PBORCTL_BOR_SH 2 | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_LDOPCTL register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_LDOPCTL_MASK 0x0000003F // Voltage adjust mask | |
#define SYSCTL_LDOPCTL_2_25V 0x00000005 // LDO output of 2.25V | |
#define SYSCTL_LDOPCTL_2_30V 0x00000004 // LDO output of 2.30V | |
#define SYSCTL_LDOPCTL_2_35V 0x00000003 // LDO output of 2.35V | |
#define SYSCTL_LDOPCTL_2_40V 0x00000002 // LDO output of 2.40V | |
#define SYSCTL_LDOPCTL_2_45V 0x00000001 // LDO output of 2.45V | |
#define SYSCTL_LDOPCTL_2_50V 0x00000000 // LDO output of 2.50V | |
#define SYSCTL_LDOPCTL_2_55V 0x0000001F // LDO output of 2.55V | |
#define SYSCTL_LDOPCTL_2_60V 0x0000001E // LDO output of 2.60V | |
#define SYSCTL_LDOPCTL_2_65V 0x0000001D // LDO output of 2.65V | |
#define SYSCTL_LDOPCTL_2_70V 0x0000001C // LDO output of 2.70V | |
#define SYSCTL_LDOPCTL_2_75V 0x0000001B // LDO output of 2.75V | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_SRCR0, SYSCTL_RCGC0, | |
// SYSCTL_SCGC0, and SYSCTL_DCGC0 registers. | |
// | |
//***************************************************************************** | |
#define SYSCTL_SET0_PWM 0x00100000 // PWM module | |
#define SYSCTL_SET0_ADC 0x00010000 // ADC module | |
#define SYSCTL_SET0_WDOG 0x00000008 // Watchdog module | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_SRCR1, SYSCTL_RCGC1, | |
// SYSCTL_SCGC1, and SYSCTL_DCGC1 registers. | |
// | |
//***************************************************************************** | |
#define SYSCTL_SET1_COMP2 0x04000000 // Analog comparator module 2 | |
#define SYSCTL_SET1_COMP1 0x02000000 // Analog comparator module 1 | |
#define SYSCTL_SET1_COMP0 0x01000000 // Analog comparator module 0 | |
#define SYSCTL_SET1_TIMER2 0x00040000 // Timer module 2 | |
#define SYSCTL_SET1_TIMER1 0x00020000 // Timer module 1 | |
#define SYSCTL_SET1_TIMER0 0x00010000 // Timer module 0 | |
#define SYSCTL_SET1_I2C 0x00001000 // I2C module | |
#define SYSCTL_SET1_SSI 0x00000010 // SSI module | |
#define SYSCTL_SET1_UART1 0x00000002 // UART module 1 | |
#define SYSCTL_SET1_UART0 0x00000001 // UART module 0 | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_SRCR2, SYSCTL_RCGC2, | |
// SYSCTL_SCGC2, and SYSCTL_DCGC2 registers. | |
// | |
//***************************************************************************** | |
#define SYSCTL_SET2_GPIOE 0x00000010 // GPIO E module | |
#define SYSCTL_SET2_GPIOD 0x00000008 // GPIO D module | |
#define SYSCTL_SET2_GPIOC 0x00000004 // GPIO C module | |
#define SYSCTL_SET2_GPIOB 0x00000002 // GPIO B module | |
#define SYSCTL_SET2_GPIOA 0x00000001 // GIPO A module | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_RIS, SYSCTL_IMC, and | |
// SYSCTL_IMS registers. | |
// | |
//***************************************************************************** | |
#define SYSCTL_INT_PLL_LOCK 0x00000040 // PLL lock interrupt | |
#define SYSCTL_INT_CUR_LIMIT 0x00000020 // Current limit interrupt | |
#define SYSCTL_INT_IOSC_FAIL 0x00000010 // Internal oscillator failure int | |
#define SYSCTL_INT_MOSC_FAIL 0x00000008 // Main oscillator failure int | |
#define SYSCTL_INT_POR 0x00000004 // Power on reset interrupt | |
#define SYSCTL_INT_BOR 0x00000002 // Brown out interrupt | |
#define SYSCTL_INT_PLL_FAIL 0x00000001 // PLL failure interrupt | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_RESC register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_RESC_LDO 0x00000020 // LDO power OK lost reset | |
#define SYSCTL_RESC_SW 0x00000010 // Software reset | |
#define SYSCTL_RESC_WDOG 0x00000008 // Watchdog reset | |
#define SYSCTL_RESC_BOR 0x00000004 // Brown-out reset | |
#define SYSCTL_RESC_POR 0x00000002 // Power on reset | |
#define SYSCTL_RESC_EXT 0x00000001 // External reset | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_RCC register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_RCC_ACG 0x08000000 // Automatic clock gating | |
#define SYSCTL_RCC_SYSDIV_MASK 0x07800000 // System clock divider | |
#define SYSCTL_RCC_SYSDIV_2 0x00800000 // System clock /2 | |
#define SYSCTL_RCC_SYSDIV_3 0x01000000 // System clock /3 | |
#define SYSCTL_RCC_SYSDIV_4 0x01800000 // System clock /4 | |
#define SYSCTL_RCC_SYSDIV_5 0x02000000 // System clock /5 | |
#define SYSCTL_RCC_SYSDIV_6 0x02800000 // System clock /6 | |
#define SYSCTL_RCC_SYSDIV_7 0x03000000 // System clock /7 | |
#define SYSCTL_RCC_SYSDIV_8 0x03800000 // System clock /8 | |
#define SYSCTL_RCC_SYSDIV_9 0x04000000 // System clock /9 | |
#define SYSCTL_RCC_SYSDIV_10 0x04800000 // System clock /10 | |
#define SYSCTL_RCC_SYSDIV_11 0x05000000 // System clock /11 | |
#define SYSCTL_RCC_SYSDIV_12 0x05800000 // System clock /12 | |
#define SYSCTL_RCC_SYSDIV_13 0x06000000 // System clock /13 | |
#define SYSCTL_RCC_SYSDIV_14 0x06800000 // System clock /14 | |
#define SYSCTL_RCC_SYSDIV_15 0x07000000 // System clock /15 | |
#define SYSCTL_RCC_SYSDIV_16 0x07800000 // System clock /16 | |
#define SYSCTL_RCC_USE_SYSDIV 0x00400000 // Use sytem clock divider | |
#define SYSCTL_RCC_USE_PWMDIV 0x00100000 // Use PWM clock divider | |
#define SYSCTL_RCC_PWMDIV_MASK 0x000E0000 // PWM clock divider | |
#define SYSCTL_RCC_PWMDIV_2 0x00000000 // PWM clock /2 | |
#define SYSCTL_RCC_PWMDIV_4 0x00020000 // PWM clock /4 | |
#define SYSCTL_RCC_PWMDIV_8 0x00040000 // PWM clock /8 | |
#define SYSCTL_RCC_PWMDIV_16 0x00060000 // PWM clock /16 | |
#define SYSCTL_RCC_PWMDIV_32 0x00080000 // PWM clock /32 | |
#define SYSCTL_RCC_PWMDIV_64 0x000A0000 // PWM clock /64 | |
#define SYSCTL_RCC_PWRDN 0x00002000 // PLL power down | |
#define SYSCTL_RCC_OE 0x00001000 // PLL output enable | |
#define SYSCTL_RCC_BYPASS 0x00000800 // PLL bypass | |
#define SYSCTL_RCC_PLLVER 0x00000400 // PLL verification timer enable | |
#define SYSCTL_RCC_XTAL_MASK 0x000003C0 // Crystal attached to main osc | |
#define SYSCTL_RCC_XTAL_3_57MHZ 0x00000100 // Using a 3.579545MHz crystal | |
#define SYSCTL_RCC_XTAL_3_68MHz 0x00000140 // Using a 3.6864MHz crystal | |
#define SYSCTL_RCC_XTAL_4MHz 0x00000180 // Using a 4MHz crystal | |
#define SYSCTL_RCC_XTAL_4_09MHZ 0x000001C0 // Using a 4.096MHz crystal | |
#define SYSCTL_RCC_XTAL_4_91MHZ 0x00000200 // Using a 4.9152MHz crystal | |
#define SYSCTL_RCC_XTAL_5MHZ 0x00000240 // Using a 5MHz crystal | |
#define SYSCTL_RCC_XTAL_5_12MHZ 0x00000280 // Using a 5.12MHz crystal | |
#define SYSCTL_RCC_XTAL_6MHZ 0x000002C0 // Using a 6MHz crystal | |
#define SYSCTL_RCC_XTAL_6_14MHZ 0x00000300 // Using a 6.144MHz crystal | |
#define SYSCTL_RCC_XTAL_7_37MHZ 0x00000340 // Using a 7.3728MHz crystal | |
#define SYSCTL_RCC_XTAL_8MHZ 0x00000380 // Using a 8MHz crystal | |
#define SYSCTL_RCC_XTAL_8_19MHZ 0x000003C0 // Using a 8.192MHz crystal | |
#define SYSCTL_RCC_OSCSRC_MASK 0x00000030 // Oscillator input select | |
#define SYSCTL_RCC_OSCSRC_MAIN 0x00000000 // Use the main oscillator | |
#define SYSCTL_RCC_OSCSRC_INT 0x00000010 // Use the internal oscillator | |
#define SYSCTL_RCC_OSCSRC_INT4 0x00000020 // Use the internal oscillator / 4 | |
#define SYSCTL_RCC_IOSCVER 0x00000008 // Int. osc. verification timer en | |
#define SYSCTL_RCC_MOSCVER 0x00000004 // Main osc. verification timer en | |
#define SYSCTL_RCC_IOSCDIS 0x00000002 // Internal oscillator disable | |
#define SYSCTL_RCC_MOSCDIS 0x00000001 // Main oscillator disable | |
#define SYSCTL_RCC_SYSDIV_SHIFT 23 // Shift to the SYSDIV field | |
#define SYSCTL_RCC_PWMDIV_SHIFT 17 // Shift to the PWMDIV field | |
#define SYSCTL_RCC_XTAL_SHIFT 6 // Shift to the XTAL field | |
#define SYSCTL_RCC_OSCSRC_SHIFT 4 // Shift to the OSCSRC field | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_PLLCFG register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_PLLCFG_OD_MASK 0x0000C000 // Output divider | |
#define SYSCTL_PLLCFG_OD_1 0x00000000 // Output divider is 1 | |
#define SYSCTL_PLLCFG_OD_2 0x00004000 // Output divider is 2 | |
#define SYSCTL_PLLCFG_OD_4 0x00008000 // Output divider is 4 | |
#define SYSCTL_PLLCFG_F_MASK 0x00003FE0 // PLL multiplier | |
#define SYSCTL_PLLCFG_R_MASK 0x0000001F // Input predivider | |
#define SYSCTL_PLLCFG_F_SHIFT 5 | |
#define SYSCTL_PLLCFG_R_SHIFT 0 | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_CLKVCLR register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_CLKVCLR_CLR 0x00000001 // Clear clock verification fault | |
//***************************************************************************** | |
// | |
// The following define the bit fields in the SYSCTL_LDOARST register. | |
// | |
//***************************************************************************** | |
#define SYSCTL_LDOARST_ARST 0x00000001 // Allow LDO to reset device | |
#endif // __HW_SYSCTL_H__ |