| # Status Codes | |
| Status codes are sent from the NCP to the host via | |
| `PROP_LAST_STATUS` using the `CMD_VALUE_IS` command to indicate | |
| the return status of a previous command. As with any response, | |
| the TID field of the FLAG byte is used to correlate the response | |
| with the request. | |
| Note that most successfully executed commands do not indicate | |
| a last status of `STATUS_OK`. The usual way the NCP indicates a | |
| successful command is to mirror the property change back to the | |
| host. For example, if you do a `CMD_VALUE_SET` on `PROP_PHY_ENABLED`, | |
| the NCP would indicate success by responding with a `CMD_VALUE_IS` | |
| for `PROP_PHY_ENABLED`. If the command failed, `PROP_LAST_STATUS` | |
| would be emitted instead. | |
| See (#prop-last-status) for more information on `PROP_LAST_STATUS`. | |
| * 0: `STATUS_OK`: Operation has completed successfully. | |
| * 1: `STATUS_FAILURE`: Operation has failed for some undefined | |
| reason. | |
| * 2: `STATUS_UNIMPLEMENTED`: The given operation has not been implemented. | |
| * 3: `STATUS_INVALID_ARGUMENT`: An argument to the given operation is invalid. | |
| * 4: `STATUS_INVALID_STATE` : The given operation is invalid for the current | |
| state of the device. | |
| * 5: `STATUS_INVALID_COMMAND`: The given command is not recognized. | |
| * 6: `STATUS_INVALID_INTERFACE`: The given Spinel interface is not supported. | |
| * 7: `STATUS_INTERNAL_ERROR`: An internal runtime error has occurred. | |
| * 8: `STATUS_SECURITY_ERROR`: A security or authentication error has occurred. | |
| * 9: `STATUS_PARSE_ERROR`: An error has occurred while parsing the command. | |
| * 10: `STATUS_IN_PROGRESS`: The operation is in progress and will be | |
| completed asynchronously. | |
| * 11: `STATUS_NOMEM`: The operation has been prevented due to memory | |
| pressure. | |
| * 12: `STATUS_BUSY`: The device is currently performing a mutually exclusive | |
| operation. | |
| * 13: `STATUS_PROP_NOT_FOUND`: The given property is not recognized. | |
| * 14: `STATUS_PACKET_DROPPED`: The packet was dropped. | |
| * 15: `STATUS_EMPTY`: The result of the operation is empty. | |
| * 16: `STATUS_CMD_TOO_BIG`: The command was too large to fit in the internal | |
| buffer. | |
| * 17: `STATUS_NO_ACK`: The packet was not acknowledged. | |
| * 18: `STATUS_CCA_FAILURE`: The packet was not sent due to a CCA failure. | |
| * 19: `STATUS_ALREADY`: The operation is already in progress or | |
| the property was already set to the given value. | |
| * 20: `STATUS_ITEM_NOT_FOUND`: The given item could not be found in the property. | |
| * 21: `STATUS_INVALID_COMMAND_FOR_PROP`: The given command cannot be performed | |
| on this property. | |
| * 22-111: RESERVED | |
| * 112-127: Reset Causes | |
| * 112: `STATUS_RESET_POWER_ON` | |
| * 113: `STATUS_RESET_EXTERNAL` | |
| * 114: `STATUS_RESET_SOFTWARE` | |
| * 115: `STATUS_RESET_FAULT` | |
| * 116: `STATUS_RESET_CRASH` | |
| * 117: `STATUS_RESET_ASSERT` | |
| * 118: `STATUS_RESET_OTHER` | |
| * 119: `STATUS_RESET_UNKNOWN` | |
| * 120: `STATUS_RESET_WATCHDOG` | |
| * 121-127: RESERVED-RESET-CODES | |
| * 128 - 15,359: UNALLOCATED | |
| * 15,360 - 16,383: Vendor-specific | |
| * 16,384 - 1,999,999: UNALLOCATED | |
| * 2,000,000 - 2,097,151: Experimental Use Only (MUST NEVER be used | |
| in production!) | |