/*
 * Handling of Ethernet PHY's
 * PHY's communicate with an EMAC either through
 * a Media-Independent Interface (MII), or a Reduced Media-Independent Interface (RMII).
 * The EMAC can poll for PHY ports on 32 different addresses. Each of the PHY ports
 * shall be treated independently.
 * 
 */

/* Standard includes. */
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>

/* FreeRTOS includes. */
#include "FreeRTOS.h"
#include "task.h"
#include "queue.h"
#include "semphr.h"

/* FreeRTOS+TCP includes. */
#include "FreeRTOS_IP.h"
#include "FreeRTOS_Sockets.h"

#include "phyHandling.h"

#include "eventLogging.h"

#define phyMIN_PHY_ADDRESS		0
#define phyMAX_PHY_ADDRESS		31

#if defined( PHY_LS_HIGH_CHECK_TIME_MS ) || defined( PHY_LS_LOW_CHECK_TIME_MS )
	#warning please use the new defines with 'ipconfig' prefix
#endif

#ifndef	ipconfigPHY_LS_HIGH_CHECK_TIME_MS
	/* Check if the LinkSStatus in the PHY is still high after 15 seconds of not
	receiving packets. */
	#define ipconfigPHY_LS_HIGH_CHECK_TIME_MS	15000
#endif

#ifndef	ipconfigPHY_LS_LOW_CHECK_TIME_MS
	/* Check if the LinkSStatus in the PHY is still low every second. */
	#define ipconfigPHY_LS_LOW_CHECK_TIME_MS	1000
#endif

/* Naming and numbering of basic PHY registers. */
#define phyREG_00_BMCR				0x00u	/* Basic Mode Control Register. */
#define phyREG_01_BMSR				0x01u	/* Basic Mode Status Register. */
#define phyREG_02_PHYSID1			0x02u	/* PHYS ID 1 */
#define phyREG_03_PHYSID2			0x03u	/* PHYS ID 2 */
#define phyREG_04_ADVERTISE			0x04u	/* Advertisement control reg */

/* Naming and numbering of extended PHY registers. */
#define PHYREG_10_PHYSTS			0x10u	/* 16 PHY status register Offset */
#define	phyREG_19_PHYCR				0x19u	/* 25 RW PHY Control Register */
#define	phyREG_1F_PHYSPCS			0x1Fu	/* 31 RW PHY Special Control Status */

/* Bit fields for 'phyREG_00_BMCR', the 'Basic Mode Control Register'. */
#define phyBMCR_FULL_DUPLEX			0x0100u	/* Full duplex. */
#define phyBMCR_AN_RESTART			0x0200u	/* Auto negotiation restart. */
#define phyBMCR_AN_ENABLE			0x1000u	/* Enable auto negotiation. */
#define phyBMCR_SPEED_100			0x2000u	/* Select 100Mbps. */
#define phyBMCR_RESET				0x8000u	/* Reset the PHY. */

/* Bit fields for 'phyREG_19_PHYCR', the 'PHY Control Register'. */
#define PHYCR_MDIX_EN				0x8000u	/* Enable Auto MDIX. */
#define PHYCR_MDIX_FORCE			0x4000u	/* Force MDIX crossed. */

#define phyBMSR_AN_COMPLETE			0x0020u	/* Auto-Negotiation process completed */

#define phyBMSR_LINK_STATUS			0x0004u

#define phyPHYSTS_LINK_STATUS		0x0001u	/* PHY Link mask */
#define phyPHYSTS_SPEED_STATUS		0x0002u	/* PHY Speed mask */
#define phyPHYSTS_DUPLEX_STATUS		0x0004u	/* PHY Duplex mask */

/* Bit fields for 'phyREG_1F_PHYSPCS
	001 = 10BASE-T half-duplex
	101 = 10BASE-T full-duplex
	010 = 100BASE-TX half-duplex
	110 = 100BASE-TX full-duplex
*/
#define phyPHYSPCS_SPEED_MASK		0x000Cu
#define phyPHYSPCS_SPEED_10			0x0004u
#define phyPHYSPCS_FULL_DUPLEX		0x0010u

/*
 * Description of all capabilities that can be advertised to
 * the peer (usually a switch or router).
 */
#define phyADVERTISE_CSMA			0x0001u	/* Only selector supported. */
#define phyADVERTISE_10HALF			0x0020u	/* Try for 10mbps half-duplex. */
#define phyADVERTISE_10FULL			0x0040u	/* Try for 10mbps full-duplex. */
#define phyADVERTISE_100HALF		0x0080u	/* Try for 100mbps half-duplex. */
#define phyADVERTISE_100FULL		0x0100u	/* Try for 100mbps full-duplex. */

#define phyADVERTISE_ALL			( phyADVERTISE_10HALF | phyADVERTISE_10FULL | \
									  phyADVERTISE_100HALF | phyADVERTISE_100FULL )

/* Send a reset commando to a set of PHY-ports. */
static uint32_t xPhyReset( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask );

static BaseType_t xHas_1F_PHYSPCS( uint32_t ulPhyID )
{
BaseType_t xResult;

	switch( ulPhyID )
	{
		case PHY_ID_LAN8720:
		case PHY_ID_LAN8742A:
		case PHY_ID_KSZ8041:
/*
		case PHY_ID_KSZ8051: // same ID as 8041
		case PHY_ID_KSZ8081: // same ID as 8041
*/
		case PHY_ID_KSZ8863:
		default:
			/* Most PHY's have a 1F_PHYSPCS */
			xResult = pdTRUE;
			break;
		case PHY_ID_DP83848I:
			xResult = pdFALSE;
			break;
	}
	return xResult;
}
/*-----------------------------------------------------------*/

static BaseType_t xHas_19_PHYCR( uint32_t ulPhyID )
{
BaseType_t xResult;

	switch( ulPhyID )
	{
		case PHY_ID_LAN8742A:
		case PHY_ID_DP83848I:
			xResult = pdTRUE;
			break;
		default:
			/* Most PHY's do not have a 19_PHYCR */
			xResult = pdFALSE;
			break;
	}
	return xResult;
}
/*-----------------------------------------------------------*/

/* Initialise the struct and assign a PHY-read and -write function. */
void vPhyInitialise( EthernetPhy_t *pxPhyObject, xApplicationPhyReadHook_t fnPhyRead, xApplicationPhyWriteHook_t fnPhyWrite )
{
	memset( ( void * )pxPhyObject, '\0', sizeof( *pxPhyObject ) );

	pxPhyObject->fnPhyRead = fnPhyRead;
	pxPhyObject->fnPhyWrite = fnPhyWrite;
}
/*-----------------------------------------------------------*/

/* Discover all PHY's connected by polling 32 indexes ( zero-based ) */
BaseType_t xPhyDiscover( EthernetPhy_t *pxPhyObject )
{
BaseType_t xPhyAddress;

	pxPhyObject->xPortCount = 0;

	for( xPhyAddress = phyMIN_PHY_ADDRESS; xPhyAddress <= phyMAX_PHY_ADDRESS; xPhyAddress++ )
	{
	uint32_t ulLowerID;

		pxPhyObject->fnPhyRead( xPhyAddress, phyREG_03_PHYSID2, &ulLowerID );
		/* A valid PHY id can not be all zeros or all ones. */
		if( ( ulLowerID != ( uint16_t )~0u )  && ( ulLowerID != ( uint16_t )0u ) )
		{
		uint32_t ulUpperID;
		uint32_t ulPhyID;

			pxPhyObject->fnPhyRead( xPhyAddress, phyREG_02_PHYSID1, &ulUpperID );
			ulPhyID = ( ( ( uint32_t ) ulUpperID ) << 16 ) | ( ulLowerID & 0xFFF0 );

			pxPhyObject->ucPhyIndexes[ pxPhyObject->xPortCount ] = xPhyAddress;
			pxPhyObject->ulPhyIDs[ pxPhyObject->xPortCount ] = ulPhyID;

			pxPhyObject->xPortCount++;

			/* See if there is more storage space. */
			if( pxPhyObject->xPortCount == ipconfigPHY_MAX_PORTS )
			{
				break;
			}
		}
	}
	if( pxPhyObject->xPortCount > 0 )
	{
		FreeRTOS_printf( ( "PHY ID %lX\n", pxPhyObject->ulPhyIDs[ 0 ] ) );
		eventLogAdd( "PHY ID 0x%lX", pxPhyObject->ulPhyIDs[ 0 ] );
	}

	return pxPhyObject->xPortCount;
}
/*-----------------------------------------------------------*/

/* Send a reset commando to a set of PHY-ports. */
static uint32_t xPhyReset( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask )
{
uint32_t ulDoneMask, ulConfig;
TickType_t xRemainingTime;
TimeOut_t xTimer;
BaseType_t xPhyIndex;

	/* A bit-mask ofPHY ports that are ready. */
	ulDoneMask = 0ul;

	/* Set the RESET bits high. */
	for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
	{
	BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

		/* Read Control register. */
		pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
		pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, ulConfig | phyBMCR_RESET );
	}

	xRemainingTime = ( TickType_t ) pdMS_TO_TICKS( 1000UL );
	vTaskSetTimeOutState( &xTimer );

	/* The reset should last less than a second. */
	for( ;; )
	{
		for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
		{
		BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

			pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
			if( ( ulConfig & phyBMCR_RESET ) == 0 )
			{
				FreeRTOS_printf( ( "xPhyReset: phyBMCR_RESET %d ready\n", (int)xPhyIndex ) );
				ulDoneMask |= ( 1ul << xPhyIndex );
			}
		}
		if( ulDoneMask == ulPhyMask )
		{
			break;
		}
		if( xTaskCheckForTimeOut( &xTimer, &xRemainingTime ) != pdFALSE )
		{
			FreeRTOS_printf( ( "xPhyReset: phyBMCR_RESET timed out ( done 0x%02lX )\n", ulDoneMask ) );
			break;
		}
	}

	/* Clear the reset bits. */
	for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
	{
	BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

		pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );
		pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, ulConfig & ~phyBMCR_RESET );
	}

	vTaskDelay( pdMS_TO_TICKS( 50ul ) );
	eventLogAdd( "PHY reset %d ports", (int)pxPhyObject->xPortCount );
	return ulDoneMask;
}
/*-----------------------------------------------------------*/

BaseType_t xPhyConfigure( EthernetPhy_t *pxPhyObject, const PhyProperties_t *pxPhyProperties )
{
uint32_t ulConfig, ulAdvertise;
BaseType_t xPhyIndex;

	if( pxPhyObject->xPortCount < 1 )
	{
		FreeRTOS_printf( ( "xPhyResetAll: No PHY's detected.\n" ) );
		return -1;
	}

	/* The expected ID for the 'LAN8742A'  is 0x0007c130. */
	/* The expected ID for the 'LAN8720'   is 0x0007c0f0. */
	/* The expected ID for the 'DP83848I'  is 0x20005C90. */

    /* Set advertise register. */
	if( ( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_AUTO ) && ( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_AUTO ) )
	{
		ulAdvertise = phyADVERTISE_CSMA | phyADVERTISE_ALL;
		/* Reset auto-negotiation capability. */
	}
	else
	{
		ulAdvertise = phyADVERTISE_CSMA;

		if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_AUTO )
		{
			if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
			{
				ulAdvertise |= phyADVERTISE_10FULL | phyADVERTISE_100FULL;
			}
			else
			{
				ulAdvertise |= phyADVERTISE_10HALF | phyADVERTISE_100HALF;
			}
		}
		else if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_AUTO )
		{
			if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_10 )
			{
				ulAdvertise |= phyADVERTISE_10FULL | phyADVERTISE_10HALF;
			}
			else
			{
				ulAdvertise |= phyADVERTISE_100FULL | phyADVERTISE_100HALF;
			}
		}
		else if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_100 )
		{
			if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
			{
				ulAdvertise |= phyADVERTISE_100FULL;
			}
			else
			{
				ulAdvertise |= phyADVERTISE_100HALF;
			}
		}
		else
		{
			if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
			{
				ulAdvertise |= phyADVERTISE_10FULL;
			}
			else
			{
				ulAdvertise |= phyADVERTISE_10HALF;
			}
		}
	}

	/* Send a reset commando to a set of PHY-ports. */
	xPhyReset( pxPhyObject, xPhyGetMask( pxPhyObject ) );

	for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
	{
	BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
	uint32_t ulPhyID = pxPhyObject->ulPhyIDs[ xPhyIndex ];

		/* Write advertise register. */
		pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_04_ADVERTISE, ulAdvertise );

		/*
				AN_EN        AN1         AN0       Forced Mode
				  0           0           0        10BASE-T, Half-Duplex
				  0           0           1        10BASE-T, Full-Duplex
				  0           1           0        100BASE-TX, Half-Duplex
				  0           1           1        100BASE-TX, Full-Duplex
				AN_EN        AN1         AN0       Advertised Mode
				  1           0           0        10BASE-T, Half/Full-Duplex
				  1           0           1        100BASE-TX, Half/Full-Duplex
				  1           1           0        10BASE-T Half-Duplex
												   100BASE-TX, Half-Duplex
				  1           1           1        10BASE-T, Half/Full-Duplex
												   100BASE-TX, Half/Full-Duplex
		*/

		/* Read Control register. */
		pxPhyObject->fnPhyRead( xPhyAddress, phyREG_00_BMCR, &ulConfig );

		ulConfig &= ~( phyBMCR_SPEED_100 | phyBMCR_FULL_DUPLEX );

		ulConfig |= phyBMCR_AN_ENABLE;

		if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_100 )
		{
			ulConfig |= phyBMCR_SPEED_100;
		}
		else if( pxPhyProperties->ucSpeed == ( uint8_t )PHY_SPEED_10 )
		{
			ulConfig &= ~phyBMCR_SPEED_100;
		}

		if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_FULL )
		{
			ulConfig |= phyBMCR_FULL_DUPLEX;
		}
		else if( pxPhyProperties->ucDuplex == ( uint8_t )PHY_DUPLEX_HALF )
		{
			ulConfig &= ~phyBMCR_FULL_DUPLEX;
		}

		if( xHas_19_PHYCR( ulPhyID ) )
		{
		uint32_t ulPhyControl;
			/* Read PHY Control register. */
			pxPhyObject->fnPhyRead( xPhyAddress, phyREG_19_PHYCR, &ulPhyControl );

			/* Clear bits which might get set: */
			ulPhyControl &= ~( PHYCR_MDIX_EN|PHYCR_MDIX_FORCE );

			if( pxPhyProperties->ucMDI_X == PHY_MDIX_AUTO )
			{
				ulPhyControl |= PHYCR_MDIX_EN;
			}
			else if( pxPhyProperties->ucMDI_X == PHY_MDIX_CROSSED )
			{
				/* Force direct link = Use crossed RJ45 cable. */
				ulPhyControl &= ~PHYCR_MDIX_FORCE;
			}
			else
			{
				/* Force crossed link = Use direct RJ45 cable. */
				ulPhyControl |= PHYCR_MDIX_FORCE;
			}
			/* update PHY Control Register. */
			pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_19_PHYCR, ulPhyControl );
		}

		FreeRTOS_printf( ( "+TCP: advertise: %04lX config %04lX\n", ulAdvertise, ulConfig ) );
		eventLogAdd( "adv: %04lX config %04lX", ulAdvertise, ulConfig );
	}

	/* Keep these values for later use. */
	pxPhyObject->ulBCRValue = ulConfig;
	pxPhyObject->ulACRValue = ulAdvertise;

	return 0;
}
/*-----------------------------------------------------------*/

BaseType_t xPhyFixedValue( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask )
{
BaseType_t xPhyIndex;
uint32_t ulValue, ulBitMask = ( uint32_t )1u;

	ulValue = ( uint32_t )0u;

	if( pxPhyObject->xPhyPreferences.ucDuplex == PHY_DUPLEX_FULL )
	{
		ulValue |= phyBMCR_FULL_DUPLEX;
	}
	if( pxPhyObject->xPhyPreferences.ucSpeed == PHY_SPEED_100 )
	{
		ulValue |= phyBMCR_SPEED_100;
	}

	for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
	{
		if( ( ulPhyMask & ulBitMask ) != 0lu )
		{
		BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

			/* Enable Auto-Negotiation. */
			pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, ulValue );
		}
	}
	return 0;
}
/*-----------------------------------------------------------*/

BaseType_t xPhyStartAutoNegotiation( EthernetPhy_t *pxPhyObject, uint32_t ulPhyMask )
{
uint32_t xPhyIndex, ulDoneMask, ulBitMask;
uint32_t ulPHYLinkStatus, ulRegValue;
TickType_t xRemainingTime;
TimeOut_t xTimer;

	if( ulPhyMask == ( uint32_t )0u )
	{
		return 0;
	}
	for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++ )
	{
		if( ( ulPhyMask & ( 1lu << xPhyIndex ) ) != 0lu )
		{
		BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

			/* Enable Auto-Negotiation. */
			pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_04_ADVERTISE, pxPhyObject->ulACRValue);
			pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, pxPhyObject->ulBCRValue | phyBMCR_AN_RESTART );
		}
	}
eventLogAdd( "AN start" );
	xRemainingTime = ( TickType_t ) pdMS_TO_TICKS( 3000UL );
	vTaskSetTimeOutState( &xTimer );
	ulDoneMask = 0;
	/* Wait until the auto-negotiation will be completed */
	for( ;; )
	{
		ulBitMask = ( uint32_t )1u;
		for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
		{
			if( ( ulPhyMask & ulBitMask ) != 0lu )
			{
				if( ( ulDoneMask & ulBitMask ) == 0lu )
				{
				BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

					pxPhyObject->fnPhyRead( xPhyAddress, phyREG_01_BMSR, &ulRegValue );
					if( ( ulRegValue & phyBMSR_AN_COMPLETE ) != 0 )
					{
						ulDoneMask |= ulBitMask;
					}
				}
			}
		}
		if( ulPhyMask == ulDoneMask )
		{
			break;
		}
		if( xTaskCheckForTimeOut( &xTimer, &xRemainingTime ) != pdFALSE )
		{
			FreeRTOS_printf( ( "xPhyReset: phyBMCR_RESET timed out ( done 0x%02lX )\n", ulDoneMask ) );
			eventLogAdd( "ANtimed out");
			break;
		}
	}
eventLogAdd( "AN done %02lX / %02lX", ulDoneMask, ulPhyMask );

	if( ulDoneMask != ( uint32_t)0u )
	{
		ulBitMask = ( uint32_t )1u;
		pxPhyObject->ulLinkStatusMask &= ~( ulDoneMask );
		for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
		{
		BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];
		uint32_t ulPhyID = pxPhyObject->ulPhyIDs[ xPhyIndex ];

			if( ( ulDoneMask & ulBitMask ) == ( uint32_t )0u )
			{
				continue;
			}

			/* Clear the 'phyBMCR_AN_RESTART'  bit. */
			pxPhyObject->fnPhyWrite( xPhyAddress, phyREG_00_BMCR, pxPhyObject->ulBCRValue );

			pxPhyObject->fnPhyRead( xPhyAddress, phyREG_01_BMSR, &ulRegValue);
			if( ( ulRegValue & phyBMSR_LINK_STATUS ) != 0 )
			{
				ulPHYLinkStatus |= phyBMSR_LINK_STATUS;
				pxPhyObject->ulLinkStatusMask |= ulBitMask;
			}
			else
			{
				ulPHYLinkStatus &= ~( phyBMSR_LINK_STATUS );
			}

			if( xHas_1F_PHYSPCS( ulPhyID ) )
			{
			/* 31 RW PHY Special Control Status */
			uint32_t ulControlStatus;

				pxPhyObject->fnPhyRead( xPhyAddress, phyREG_1F_PHYSPCS, &ulControlStatus);
				ulRegValue = 0;
				if( ( ulControlStatus & phyPHYSPCS_FULL_DUPLEX ) != 0 )
				{
					ulRegValue |= phyPHYSTS_DUPLEX_STATUS;
				}
				if( ( ulControlStatus & phyPHYSPCS_SPEED_MASK ) == phyPHYSPCS_SPEED_10 )
				{
					ulRegValue |= phyPHYSTS_SPEED_STATUS;
				}

			}
			else
			{
				/* Read the result of the auto-negotiation. */
				pxPhyObject->fnPhyRead( xPhyAddress, PHYREG_10_PHYSTS, &ulRegValue);
			}

			FreeRTOS_printf( ( ">> Autonego ready: %08lx: %s duplex %u mbit %s status\n",
				ulRegValue,
				( ulRegValue & phyPHYSTS_DUPLEX_STATUS ) ? "full" : "half",
				( ulRegValue & phyPHYSTS_SPEED_STATUS ) ? 10 : 100,
				( ( ulPHYLinkStatus |= phyBMSR_LINK_STATUS ) != 0) ? "high" : "low" ) );
			eventLogAdd( "%s duplex %u mbit %s st",
				( ulRegValue & phyPHYSTS_DUPLEX_STATUS ) ? "full" : "half",
				( ulRegValue & phyPHYSTS_SPEED_STATUS ) ? 10 : 100,
				( ( ulPHYLinkStatus |= phyBMSR_LINK_STATUS ) != 0) ? "high" : "low" );
{
	uint32_t regs[4];
	int i,j;
	int address = 0x10;
	for (i = 0; i < 4; i++)
	{
		for (j = 0; j < 4; j++)
		{
			pxPhyObject->fnPhyRead( xPhyAddress, address, regs + j );
			address++;
		}
		eventLogAdd("%04lX %04lX %04lX %04lX",
			regs[0], regs[1], regs[2], regs[3]);
	}
}
			if( ( ulRegValue & phyPHYSTS_DUPLEX_STATUS ) != ( uint32_t )0u )
			{
				pxPhyObject->xPhyProperties.ucDuplex = PHY_DUPLEX_FULL;
			}
			else
			{
				pxPhyObject->xPhyProperties.ucDuplex = PHY_DUPLEX_HALF;
			}

			if( ( ulRegValue & phyPHYSTS_SPEED_STATUS ) != 0 )
			{
				pxPhyObject->xPhyProperties.ucSpeed = PHY_SPEED_10;
			}
			else
			{
				pxPhyObject->xPhyProperties.ucSpeed = PHY_SPEED_100;
			}
		}
	}	/* if( ulDoneMask != ( uint32_t)0u ) */

	return 0;
}
/*-----------------------------------------------------------*/

BaseType_t xPhyCheckLinkStatus( EthernetPhy_t *pxPhyObject, BaseType_t xHadReception )
{
uint32_t ulStatus, ulBitMask = 1u;
BaseType_t xPhyIndex;
BaseType_t xNeedCheck = pdFALSE;

	if( xHadReception > 0 )
	{
		/* A packet was received. No need to check for the PHY status now,
		but set a timer to check it later on. */
		vTaskSetTimeOutState( &( pxPhyObject->xLinkStatusTimer ) );
		pxPhyObject->xLinkStatusRemaining = pdMS_TO_TICKS( ipconfigPHY_LS_HIGH_CHECK_TIME_MS );
	}
	else if( xTaskCheckForTimeOut( &( pxPhyObject->xLinkStatusTimer ), &( pxPhyObject->xLinkStatusRemaining ) ) != pdFALSE )
	{
		for( xPhyIndex = 0; xPhyIndex < pxPhyObject->xPortCount; xPhyIndex++, ulBitMask <<= 1 )
		{
		BaseType_t xPhyAddress = pxPhyObject->ucPhyIndexes[ xPhyIndex ];

			if( pxPhyObject->fnPhyRead( xPhyAddress, phyREG_01_BMSR, &ulStatus ) == 0 )
			{
				if( !!( pxPhyObject->ulLinkStatusMask & ulBitMask ) != !!( ulStatus & phyBMSR_LINK_STATUS ) )
				{
					if( ( ulStatus & phyBMSR_LINK_STATUS ) != 0 )
					{
						pxPhyObject->ulLinkStatusMask |= ulBitMask;
					}
					else
					{
						pxPhyObject->ulLinkStatusMask &= ~( ulBitMask );
					}
					FreeRTOS_printf( ( "xPhyCheckLinkStatus: PHY LS now %02lX\n", pxPhyObject->ulLinkStatusMask ) );
					eventLogAdd( "PHY LS now %02lX", pxPhyObject->ulLinkStatusMask );
					xNeedCheck = pdTRUE;
				}
			}
		}
		vTaskSetTimeOutState( &( pxPhyObject->xLinkStatusTimer ) );
		if( ( pxPhyObject->ulLinkStatusMask & phyBMSR_LINK_STATUS ) != 0 )
		{
			pxPhyObject->xLinkStatusRemaining = pdMS_TO_TICKS( ipconfigPHY_LS_HIGH_CHECK_TIME_MS );
		}
		else
		{
			pxPhyObject->xLinkStatusRemaining = pdMS_TO_TICKS( ipconfigPHY_LS_LOW_CHECK_TIME_MS );
		}
	}
	return xNeedCheck;
}
/*-----------------------------------------------------------*/