/*
 * FreeRTOS+UDP V1.0.4
 * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy of
 * this software and associated documentation files (the "Software"), to deal in
 * the Software without restriction, including without limitation the rights to
 * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
 * the Software, and to permit persons to whom the Software is furnished to do so,
 * subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in all
 * copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
 * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
 * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
 * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
 * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
 *
 * http://www.FreeRTOS.org
 * http://aws.amazon.com/freertos
 *
 * 1 tab == 4 spaces!
 */

/*****************************************************************************
 *
 * See the following URL for configuration information.
 * http://www.FreeRTOS.org/FreeRTOS-Plus/FreeRTOS_Plus_UDP/UDP_IP_Configuration.shtml
 *
 *****************************************************************************/

#ifndef FREERTOS_IP_CONFIG_H
#define FREERTOS_IP_CONFIG_H

/* The IP stack executes it its own task (although any application task can make
use of its services through the published sockets API). ipconfigUDP_TASK_PRIORITY
sets the priority of the task that executes the IP stack.  The priority is a
standard FreeRTOS task priority so can take any value from 0 (the lowest
priority) to (configMAX_PRIORITIES - 1) (the highest priority).
configMAX_PRIORITIES is a standard FreeRTOS configuration parameter defined in
FreeRTOSConfig.h, not FreeRTOSIPConfig.h. Consideration needs to be given as to
the priority assigned to the task executing the IP stack relative to the
priority assigned to tasks that use the IP stack.

Note:  If the application is started without the network cable plugged in then
this should be set to the lowest priority - otherwise the Atmel ASF GMAC driver
will poll the GMAC interface waiting for a connection to be established.  The
driver uses a very long timeout and no lower priority tasks will be able to
execute during this time.  This demo starts with the IP task running at the idle
priority - then raises the priority of the IP task in the network event hook
when a connection has been established. */
#define ipconfigUDP_TASK_PRIORITY			( tskIDLE_PRIORITY )

/* The size, in words (not bytes), of the stack allocated to the FreeRTOS+UDP
task.  This setting is less important when the FreeRTOS Win32 simulator is used
as the Win32 simulator only stores a fixed amount of information on the task
stack.  FreeRTOS includes optional stack overflow detection, see:
http://www.freertos.org/Stacks-and-stack-overflow-checking.html */
#define ipconfigUDP_TASK_STACK_SIZE_WORDS	( configMINIMAL_STACK_SIZE * 2 )

/* ipconfigRAND32() is called by the IP stack to generate a random number that
is then used as a DHCP transaction number.  Random number generation is performed
via this macro to allow applications to use their own random number generation
method.  For example, it might be possible to generate a random number by
sampling noise on an analogue input. */
#define ipconfigRAND32()	1

/* If ipconfigUSE_NETWORK_EVENT_HOOK is set to 1 then FreeRTOS+UDP will call the
network event hook at the appropriate times.  If ipconfigUSE_NETWORK_EVENT_HOOK
is not set to 1 then the network event hook will never be called.  See
http://www.FreeRTOS.org/FreeRTOS-Plus/FreeRTOS_Plus_UDP/API/vApplicationIPNetworkEventHook.shtml
*/
#define ipconfigUSE_NETWORK_EVENT_HOOK 1

/* Sockets have a send block time attribute.  If FreeRTOS_sendto() is called but
a network buffer cannot be obtained then the calling task is held in the Blocked
state (so other tasks can continue to executed) until either a network buffer
becomes available or the send block time expires.  If the send block time expires
then the send operation is aborted.  The maximum allowable send block time is
capped to the value set by ipconfigMAX_SEND_BLOCK_TIME_TICKS.  Capping the
maximum allowable send block time prevents prevents a deadlock occurring when
all the network buffers are in use and the tasks that process (and subsequently
free) the network buffers are themselves blocked waiting for a network buffer.
ipconfigMAX_SEND_BLOCK_TIME_TICKS is specified in RTOS ticks.  A time in
milliseconds can be converted to a time in ticks by dividing the time in
milliseconds by portTICK_PERIOD_MS. */
#define ipconfigMAX_SEND_BLOCK_TIME_TICKS ( 20 / portTICK_PERIOD_MS )

/* If ipconfigUSE_DHCP is 1 then FreeRTOS+UDP will attempt to retrieve an IP
address, netmask, DNS server address and gateway address from a DHCP server.  If
ipconfigUSE_DHCP is 0 then FreeRTOS+UDP will use a static IP address.  The
stack will revert to using the static IP address even when ipconfigUSE_DHCP is
set to 1 if a valid configuration cannot be obtained from a DHCP server for any
reason.  The static configuration used is that passed into the stack by the
FreeRTOS_IPInit() function call. */
#define ipconfigUSE_DHCP	1

/* When ipconfigUSE_DHCP is set to 1, DHCP requests will be sent out at
increasing time intervals until either a reply is received from a DHCP server
and accepted, or the interval between transmissions reaches
ipconfigMAXIMUM_DISCOVER_TX_PERIOD.  The IP stack will revert to using the
static IP address passed as a parameter to FreeRTOS_IPInit() if the
re-transmission time interval reaches ipconfigMAXIMUM_DISCOVER_TX_PERIOD without
a DHCP reply being received. */
#define ipconfigMAXIMUM_DISCOVER_TX_PERIOD		( 999 / portTICK_PERIOD_MS )

/* The ARP cache is a table that maps IP addresses to MAC addresses.  The IP
stack can only send a UDP message to a remove IP address if it knowns the MAC
address associated with the IP address, or the MAC address of the router used to
contact the remote IP address.  When a UDP message is received from a remote IP
address the MAC address and IP address are added to the ARP cache.  When a UDP
message is sent to a remote IP address that does not already appear in the ARP
cache then the UDP message is replaced by a ARP message that solicits the
required MAC address information.  ipconfigARP_CACHE_ENTRIES defines the maximum
number of entries that can exist in the ARP table at any one time. */
#define ipconfigARP_CACHE_ENTRIES		6

/* ARP requests that do not result in an ARP response will be re-transmitted a
maximum of ipconfigMAX_ARP_RETRANSMISSIONS times before the ARP request is
aborted. */
#define ipconfigMAX_ARP_RETRANSMISSIONS ( 5 )

/* ipconfigMAX_ARP_AGE defines the maximum time between an entry in the ARP
table being created or refreshed and the entry being removed because it is stale.
New ARP requests are sent for ARP cache entries that are nearing their maximum
age.  ipconfigMAX_ARP_AGE is specified in tens of seconds, so a value of 150 is
equal to 1500 seconds (or 25 minutes). */
#define ipconfigMAX_ARP_AGE			150

/* Implementing FreeRTOS_inet_addr() necessitates the use of string handling
routines, which are relatively large.  To save code space the full
FreeRTOS_inet_addr() implementation is made optional, and a smaller and faster
alternative called FreeRTOS_inet_addr_quick() is provided.  FreeRTOS_inet_addr()
takes an IP in decimal dot format (for example, "192.168.0.1") as its parameter.
FreeRTOS_inet_addr_quick() takes an IP address as four separate numerical octets
(for example, 192, 168, 0, 1) as its parameters.  If
ipconfigINCLUDE_FULL_INET_ADDR is set to 1 then both FreeRTOS_inet_addr() and
FreeRTOS_indet_addr_quick() are available.  If ipconfigINCLUDE_FULL_INET_ADDR is
not set to 1 then only FreeRTOS_indet_addr_quick() is available. */
#define ipconfigINCLUDE_FULL_INET_ADDR	1

/* ipconfigNUM_NETWORK_BUFFERS defines the total number of network buffer that
are available to the IP stack.  The total number of network buffers is limited
to ensure the total amount of RAM that can be consumed by the IP stack is capped
to a pre-determinable value. */
#define ipconfigNUM_NETWORK_BUFFERS		10

/* A FreeRTOS queue is used to send events from application tasks to the IP
stack.  ipconfigEVENT_QUEUE_LENGTH sets the maximum number of events that can
be queued for processing at any one time.  The event queue must be a minimum of
5 greater than the total number of network buffers. */
#define ipconfigEVENT_QUEUE_LENGTH		( ipconfigNUM_NETWORK_BUFFERS + 5 )

/* The address of a socket is the combination of its IP address and its port
number.  FreeRTOS_bind() is used to manually allocate a port number to a socket
(to 'bind' the socket to a port), but manual binding is not normally necessary
for client sockets (those sockets that initiate outgoing connections rather than
wait for incoming connections on a known port number).  If
ipconfigALLOW_SOCKET_SEND_WITHOUT_BIND is set to 1 then calling
FreeRTOS_sendto() on a socket that has not yet been bound will result in the IP
stack automatically binding the socket to a port number from the range
socketAUTO_PORT_ALLOCATION_START_NUMBER to 0xffff.  If
ipconfigALLOW_SOCKET_SEND_WITHOUT_BIND is set to 0 then calling FreeRTOS_sendto()
on a socket that has not yet been bound will result in the send operation being
aborted. */
#define ipconfigALLOW_SOCKET_SEND_WITHOUT_BIND 1

/* Defines the Time To Live (TTL) values used in outgoing UDP packets. */
#define updconfigIP_TIME_TO_LIVE		128

/* If ipconfigCAN_FRAGMENT_OUTGOING_PACKETS is set to 1 then UDP packets that
contain more data than will fit in a single network frame will be fragmented
across multiple IP packets.  Also see the ipconfigNETWORK_MTU setting.  If
ipconfigCAN_FRAGMENT_OUTGOING_PACKETS is 1 then (ipconfigNETWORK_MTU - 28) must
be divisible by 8.  Setting ipconfigCAN_FRAGMENT_OUTGOING_PACKETS to 1 will
increase both the code size and execution time. */
#define ipconfigCAN_FRAGMENT_OUTGOING_PACKETS 0

/* The MTU is the maximum number of bytes the payload of a network frame can
contain.  For normal Ethernet V2 frames the maximum MTU is 1500.  Setting a
lower value can save RAM, depending on the buffer management scheme used.  If
ipconfigCAN_FRAGMENT_OUTGOING_PACKETS is 1 then (ipconfigNETWORK_MTU - 28) must
be divisible by 8. */
#define ipconfigNETWORK_MTU 1500 /* Leave at 1500 for SAM4E. */

/* Set ipconfigUSE_DNS to 1 to include a basic DNS client/resolver.  DNS is used
through the FreeRTOS_gethostbyname() API function. */
#define ipconfigUSE_DNS		1

/* If ipconfigREPLY_TO_INCOMING_PINGS is set to 1 then the IP stack will
generate replies to incoming ICMP echo (ping) requests. */
#define ipconfigREPLY_TO_INCOMING_PINGS				1

/* If ipconfigSUPPORT_OUTGOING_PINGS is set to 1 then the
FreeRTOS_SendPingRequest() API function is available. */
#define ipconfigSUPPORT_OUTGOING_PINGS				1

/* If ipconfigSUPPORT_SELECT_FUNCTION is set to 1 then the FreeRTOS_select()
(and associated) API function is available. */
#define ipconfigSUPPORT_SELECT_FUNCTION				1

/* Used for stack testing only, and must be implemented in the network
interface. */
#define updconfigLOOPBACK_ETHERNET_PACKETS	0

/* If ipconfigFILTER_OUT_NON_ETHERNET_II_FRAMES is set to 1 then Ethernet frames
that are not in Ethernet II format will be dropped.  This option is included for
potential future IP stack developments. */
#define ipconfigFILTER_OUT_NON_ETHERNET_II_FRAMES 1

/* If ipconfigETHERNET_DRIVER_FILTERS_FRAME_TYPES is set to 1 then it is the
responsibility of the Ethernet interface to filter out packets that are of no
interest.  If the Ethernet interface does not implement this functionality, then
set ipconfigETHERNET_DRIVER_FILTERS_FRAME_TYPES to 0 to have the IP stack
perform the filtering instead (it is much less efficient for the stack to do it
because the packet will already have been passed into the stack).  If the
Ethernet driver does all the necessary filtering in hardware then software
filtering can be removed by using a value other than 1 or 0. */
#define ipconfigETHERNET_DRIVER_FILTERS_FRAME_TYPES	0

/* If ipconfigETHERNET_DRIVER_ADDS_UDP_CHECKSUM is set to 1 then a UDP checksum
will not be calculated and added to a packet before the packet is sent to the
hardware for transmission. */
#define ipconfigETHERNET_DRIVER_ADDS_UDP_CHECKSUM	0

/* If ipconfigETHERNET_DRIVER_ADDS_IP_CHECKSUM is set to 1 then an IP checksum
will not be calculated and added to a packet before the packet is sent to the
hardware for transmission. */
#define ipconfigETHERNET_DRIVER_ADDS_IP_CHECKSUM	0

/* If ipconfigETHERNET_DRIVER_CHECKS_IP_CHECKSUM is set to 1 then the IP
checksum will be ignored on incoming packets on the assumption IP packets with
an invalid checksum are not passed to the stack. */
#define ipconfigETHERNET_DRIVER_CHECKS_IP_CHECKSUM	0

/* If ipconfigETHERNET_DRIVER_CHECKS_UDP_CHECKSUM is set to 1 then the UDP
checksum will be ignored on incoming packets on the assumption the UDP packets
with an invalid checksum are not passed to the stack. */
#define ipconfigETHERNET_DRIVER_CHECKS_UDP_CHECKSUM 0

/* Set ipconfigFREERTOS_PLUS_NABTO to 1 to support the Nabto protocol, or 0 to
exclude support for the Nabto protocol.  If ipconfigFREERTOS_PLUS_NABTO is set
to one then the project must build the Nabto source code (or reference a
pre-build Nabto library. */
#define ipconfigFREERTOS_PLUS_NABTO					0

/* Sets the size of the stack used by the Nabto service task.  The Nabto event
handler executes in the context of the Nabto service task.  If the event handler
uses a lot of stack then it is possible the value set here will need to be
increased.  It is recommended to have FreeRTOS stack overflow checking turned
on during development (see the configCHECK_FOR_STACK_OVERFLOW in
FreeRTOSConfig.h and in the documentation. */
#define ipconfigNABTO_TASK_STACK_SIZE ( configMINIMAL_STACK_SIZE * 2 )

/* Sets the priority of the Nabto service task.  This is a standard FreeRTOS
task priority so can take values between 0 (the lowest priority) and
configMAX_PRIORITIES - 1 (the highest priority).  Also see the definition of
ipconfigUDP_TASK_PRIORITY.  This would normally be set to be either one higher
or one lower than ipconfigUDP_TASK_PRIORITY, depending on the application. */
#define ipconfigNABTO_TASK_PRIORITY	 ( ipconfigUDP_TASK_PRIORITY + 1 )

/* The windows simulator cannot really simulate MAC interrupts, and needs to
block occasionally to allow other tasks to run. */
#ifdef _WINDOWS_
	#define configWINDOWS_MAC_INTERRUPT_SIMULATOR_DELAY ( 3 / portTICK_PERIOD_MS )
#endif

/* The example IP trace macros are included here so the definitions are
available in all the FreeRTOS+UDP source files. */
#include "DemoIPTrace.h"

#endif /* FREERTOS_IP_CONFIG_H */