/* ----------------------------------------------------------------------------
 *         SAM Software Package License
 * ----------------------------------------------------------------------------
 * Copyright (c) 2014, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/**
 * \page samv7_Xplained_ultra_board_desc SAMV7_Xplained_Ultra - Board Description
 *
 * \section Purpose
 *
 * This file is dedicated to describe the SAMV7_Xplained_Ultra board.
 *
 * \section Contents
 *
 *  - For SAMV7_Xplained_Ultra information, see \subpage samv7_Xplained_ultra_board_info.
 *  - For operating frequency information, see \subpage samv7_Xplained_ultra_opfreq.
 *  - For using portable PIO definitions, see \subpage samv7_Xplained_ultra_piodef.
 *  - For on-board memories, see \subpage samv7_Xplained_ultra_mem.
 *  - Several USB definitions are included here, see \subpage samv7_Xplained_ultra_usb.
 *  - For External components, see \subpage samv7_Xplained_ultra_extcomp.
 *  - For Individual chip definition, see \subpage samv7_Xplained_ultra_chipdef.
 *
 * To get more software details and the full list of parameters related to the
 * SAMV7_Xplained_Ultra board configuration, please have a look at the source file:
 * \ref board.h\n
 *
 * \section Usage
 *
 *  - The code for booting the board is provided by board_cstartup_xxx.c and
 *    board_lowlevel.c.
 *  - For using board PIOs, board characteristics (clock, etc.) and external
 *    components, see board.h.
 *  - For manipulating memories, see board_memories.h.
 *
 * This file can be used as a template and modified to fit a custom board, with
 * specific PIOs usage or memory connections.
 */

/**
 *  \file board.h
 *
 *  Definition of SAMV7_Xplained_Ultra characteristics, PIOs and
 *  external components interface.
 */

#ifndef _BOARD_H_
#define _BOARD_H_

/*----------------------------------------------------------------------------
 *        Headers
 *----------------------------------------------------------------------------*/
#include "chip.h"

#include "include/board_lowlevel.h"
#include "include/board_memories.h"
#include "include/omnivision.h"
#include "include/ov.h"
#include "include/led.h"
#include "include/gmii.h"
#include "include/gmacb_phy.h"
#include "include/dbg_console.h"
#include "include/bmp.h"
#include "include/hamming.h"
#include "include/lcdd.h"
#include "include/ili9488_reg.h"
#include "include/ili9488.h"
#include "include/frame_buffer.h"
#include "include/lcd_color.h"
#include "include/lcd_draw.h"
#include "include/lcd_font10x14.h"
#include "include/lcd_font.h"
#include "include/lcd_gimp_image.h"
#include "include/wav.h"
#include "include/wm8904.h"
#include "include/CS2100.h"
#include "include/s25fl1.h"
#include "include/omnivision.h"
#include "include/ovyuv.h"
//#include "include/s25fl1_qspi.h"

/*----------------------------------------------------------------------------
 *        Definitions
 *----------------------------------------------------------------------------*/

/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_board_info "SAMV7_Xplained_Ultra - Board informations"
 * This page lists several definition related to the board description.
 *
 * \section Definitions
 * - \ref BOARD_NAME
 */

/** Name of the board */
#define BOARD_NAME "SAMV7-EK"
#define NO_PUSHBUTTON
/*----------------------------------------------------------------------------*/
/**
 *  \page samv7_Xplained_ultra_opfreq "SAMV7_Xplained_Ultra - Operating frequencies"
 *  This page lists several definition related to the board operating frequency
 *  (when using the initialization done by board_lowlevel.c).
 *
 *  \section Definitions
 *  - \ref BOARD_MAINOSC
 *  - \ref BOARD_MCK
 */

/** Frequency of the board main oscillator */
#define BOARD_MAINOSC           12000000

/** Master clock frequency (when using board_lowlevel.c) */

#define BOARD_MCK               132000000



/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_piodef "SAMV7_Xplained_Ultra - PIO definitions"
 * This pages lists all the pio definitions contained in board.h. The constants
 * are named using the following convention: PIN_* for a constant which defines
 * a single Pin instance (but may include several PIOs sharing the same
 * controller), and PINS_* for a list of Pin instances.
 *
 * UART
 * - \ref PINS_UART
 *
 * EBI
 * - \ref PIN_EBI_DATA_BUS
 * - \ref PIN_EBI_NRD
 * - \ref PIN_EBI_NWE
 * - \ref PIN_EBI_NCS0
 * - \ref PIN_EBI_PSRAM_ADDR_BUS
 * - \ref PIN_EBI_PSRAM_NBS
 * - \ref PIN_EBI_A1
 * - \ref PIN_EBI_LCD_CS
 * - \ref PIN_EBI_LCD_RS
 *
 * LEDs
 * - \ref PIN_LED_0
 * - \ref PIN_LED_1
 * - \ref PIN_LED_2
 * - \ref PIN_LED_3
 * - \ref PINS_LEDS
 *
 * MCI
 * - \ref PINS_MCI
 *
 * Push buttons
 * - \ref PIN_PUSHBUTTON_0
 * - \ref PIN_PUSHBUTTON_1
 * - \ref PIN_PUSHBUTTON_2
 * - \ref PIN_PUSHBUTTON_3
 * - \ref PINS_PUSHBUTTONS
 * - \ref PUSHBUTTON_BP0
 * - \ref PUSHBUTTON_BP1
 * - \ref PUSHBUTTON_BP2
 * - \ref PUSHBUTTON_BP3
 *
 * PWMC
 * - \ref PIN_PWMC_PWMH0
 * - \ref PIN_PWMC_PWMH1
 * - \ref PIN_PWM_LED0
 * - \ref PIN_PWM_LED1
 * - \ref CHANNEL_PWM_LED0
 * - \ref CHANNEL_PWM_LED1
 *
 * SPI
 * - \ref PIN_SPI_MISO
 * - \ref PIN_SPI_MOSI
 * - \ref PIN_SPI_SPCK
 * - \ref PINS_SPI
 * - \ref PIN_SPI_NPCS0_PA11
 *
 * PCK0
 * - \ref PIN_PCK0
 *
 * PIO PARALLEL CAPTURE
 * - \ref PIN_PIODCEN1
 * - \ref PIN_PIODCEN2
 *
 * TWI
 * - \ref TWI_V3XX
 * - \ref PIN_TWI_TWD0
 * - \ref PIN_TWI_TWCK0
 * - \ref PINS_TWI0
 *
 * USART0
 * - \ref PIN_USART0_RXD
 * - \ref PIN_USART0_TXD
 * - \ref PIN_USART0_CTS
 * - \ref PIN_USART0_RTS
 * - \ref PIN_USART0_SCK
 *
 * USB
 * - \ref PIN_USB_VBUS
 *
 * NandFlash
 * - \ref PIN_EBI_NANDOE
 * - \ref PIN_EBI_NANDWE
 * - \ref PIN_EBI_NANDCLE
 * - \ref PIN_EBI_NANDALE
 * - \ref PIN_EBI_NANDIO
 * - \ref BOARD_NF_CE_PIN
 * - \ref BOARD_NF_RB_PIN
 * - \ref PINS_NANDFLASH
 */


/** SSC pin Transmitter Data (TD) */
#define PIN_SSC_TD      {PIO_PD26B_TD, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SSC pin Transmitter Clock (TK) */
#define PIN_SSC_TK      {PIO_PB1D_TK, PIOB, ID_PIOB, PIO_PERIPH_D, PIO_DEFAULT}
/** SSC pin Transmitter FrameSync (TF) */
#define PIN_SSC_TF      {PIO_PB0D_TF, PIOB, ID_PIOB, PIO_PERIPH_D, PIO_DEFAULT}
/** SSC pin RD */
#define PIN_SSC_RD      {PIO_PA10C_RD, PIOA, ID_PIOA, PIO_PERIPH_C, PIO_DEFAULT}
/** SSC pin RK */
#define PIN_SSC_RK      {PIO_PA22A_RK, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** SSC pin RF */
#define PIN_SSC_RF      {PIO_PD24B_RF, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}

/** SSC pins definition for codec. */
#define PINS_SSC_CODEC  {PIN_SSC_TD,  PIN_SSC_TK, PIN_SSC_TF, PIN_SSC_RD,  PIN_SSC_RK, PIN_SSC_RF}


/** UART pins (UTXD0 and URXD0) definitions, PA9,10. */
#define PINS_UART0  {PIO_PA9A_URXD0 | PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** UART pins (UTXD4 and URXD4) definitions, PD19,18. */
#define PINS_UART4  {PIO_PD18C_URXD4 | PIO_PD19C_UTXD4, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}

/** EBI Data Bus pins */
#define PIN_EBI_DATA_BUS   {0xFF, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** EBI NRD pin */
#define PIN_EBI_NRD        {1 << 11, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** EBI NWE pin */
#define PIN_EBI_NWE        {1 << 8, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** EBI NCS0 pin */
#define PIN_EBI_NCS0       {1 << 14, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}

/** EBI A1 pin */
#define PIN_EBI_A1         {1 << 19, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/* LCD CS pin (NCS3) */
#define PIN_EBI_LCD_CS     {1 << 18, PIOD, ID_PIOD, PIO_PERIPH_A, PIO_PULLUP}
/* LCD RS pin (A1) */
#define PIN_EBI_LCD_RS     {1 << 19, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}

#define LED_YELLOW0      0
#define LED_YELLOW1      1

/** LED #0 pin definition (BLUE). */
#define PIN_LED_0   {PIO_PA23, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
/** LED #0 pin definition (AMBER). */
#define PIN_LED_1   {PIO_PC9, PIOC, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT}

/** List of all LEDs definitions. */
#define PINS_LEDS   {PIN_LED_0, PIN_LED_1}


/** List of all SDRAM pin definitions. */
#define PIN_SDRAM_D0_7   {0x000000FF, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SDRAM_D8_13  {0x0000003F, PIOE, ID_PIOE, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SDRAM_D14_15 {0x00018000, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SDRAM_A0_9   {0x3FF00000, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SDRAM_SDA10  {0x00002000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
//#define PIN_SDRAM_A11    {0x80000000, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_DEFAULT}

#define PIN_SDRAM_CAS    {0x00020000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
#define PIN_SDRAM_RAS    {0x00010000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
#define PIN_SDRAM_SDCKE  {0x00004000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
#define PIN_SDRAM_SDCK   {0x00800000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
#define PIN_SDRAM_SDSC   {0x00008000, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SDRAM_NBS0   {0x00040000, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_DEFAULT}
#define PIN_SDRAM_NBS1   {0x00008000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
#define PIN_SDRAM_SDWE   {0x20000000, PIOD, ID_PIOD, PIO_PERIPH_C, PIO_DEFAULT}
#define PIN_SDRAM_BA0    {0x00100000, PIOA, ID_PIOA, PIO_PERIPH_C, PIO_DEFAULT}

#define BOARD_SDRAM_PINS  PIN_SDRAM_D0_7, PIN_SDRAM_D8_13 , PIN_SDRAM_D14_15,\
                          PIN_SDRAM_A0_9, PIN_SDRAM_SDA10, PIN_SDRAM_BA0, \
                          PIN_SDRAM_CAS, PIN_SDRAM_RAS, PIN_SDRAM_SDCKE,PIN_SDRAM_SDCK,\
                          PIN_SDRAM_SDSC,PIN_SDRAM_NBS0 ,PIN_SDRAM_NBS1,PIN_SDRAM_SDWE
/**
 * Push button #0 definition.
 * Attributes = pull-up + debounce + interrupt on rising edge.
 */
#define PIN_PUSHBUTTON_0    {PIO_PA19, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_FALL_EDGE}
/**
 * Push button #1 definition.
 * Attributes = pull-up + debounce + interrupt on rising edge.
 */
#define PIN_PUSHBUTTON_1    {PIO_PB12, PIOB, ID_PIOB, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_FALL_EDGE}

/** List of all push button definitions. */
#define PINS_PUSHBUTTONS    {PIN_PUSHBUTTON_0, PIN_PUSHBUTTON_1}


/** Push button #0 index. */
#define PUSHBUTTON_BP0   0
/** Push button #1 index. */
#define PUSHBUTTON_BP1   1
/** Push button #2 index. */
#define PUSHBUTTON_BP2   2
/** Push button #3 index. */
#define PUSHBUTTON_BP3   3

/** PWMC PWM0 pin definition: Output High. */
#define PIN_PWMC_PWMH0  {PIO_PD20A_PWMH0, PIOD, ID_PIOD, PIO_PERIPH_A, PIO_DEFAULT}
/** PWMC PWM1 pin definition: Output High. */
#define PIN_PWMC_PWMH1  {PIO_PD21A_PWMH1, PIOD, ID_PIOD, PIO_PERIPH_A, PIO_DEFAULT}
/** PWM pins definition for LED0 */
#define PIN_PWM_LED0 PIN_PWMC_PWMH0
/** PWM pins definition for LED1 */
#define PIN_PWM_LED1 PIN_PWMC_PWMH1
/** PWM channel for LED0 */
#define CHANNEL_PWM_LED0 0
/** PWM channel for LED1 */
#define CHANNEL_PWM_LED1 1

/** SPI MISO pin definition. */
#define PIN_SPI_MISO    {PIO_PD20B_SPI0_MISO, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SPI MOSI pin definition. */
#define PIN_SPI_MOSI    {PIO_PD21B_SPI0_MOSI, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SPI SPCK pin definition. */
#define PIN_SPI_SPCK    {PIO_PD22B_SPI0_SPCK, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SPI chip select pin definition. */
#define PIN_SPI_NPCS0 {PIO_PB2D_SPI0_NPCS0, PIOB, ID_PIOB, PIO_PERIPH_D, PIO_DEFAULT}
#define PIN_SPI_NPCS1 {PIO_PA31A_SPI0_NPCS1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}

#define PIN_SPI_NPCS3 {PIO_PD27B_SPI0_NPCS3, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}

/** List of SPI pin definitions (MISO, MOSI & SPCK). */
#define PINS_SPI        PIN_SPI_MISO, PIN_SPI_MOSI, PIN_SPI_SPCK

/** PCK0 */
//#define PIN_PCK0  {PIO_PB12D_PCK0, PIOB, ID_PIOB, PIO_PERIPH_D, PIO_DEFAULT}
#define PIN_PCK0  {PIO_PB13B_PCK0, PIOB, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT}
/** PCK1 */
#define PIN_PCK1  {PIO_PA17B_PCK1, PIOB, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT}

/** PCK2 */
#define PIN_PCK2  {PIO_PA18B_PCK2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}


/** PIO PARALLEL CAPTURE */
/** Parallel Capture Mode Data Enable1 */
#define PIN_PIODCEN1    PIO_PA15
/** Parallel Capture Mode Data Enable2 */
#define PIN_PIODCEN2    PIO_PA16

/** TWI ver 3.xx */
#define TWI_V3XX
/** TWI0 data pin */
#define PIN_TWI_TWD0   {PIO_PA3A_TWD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** TWI0 clock pin */
#define PIN_TWI_TWCK0  {PIO_PA4A_TWCK0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** TWI0 pins */
#define PINS_TWI0      {PIN_TWI_TWD0, PIN_TWI_TWCK0}
/** TWI1 data pin */
#define PIN_TWI_TWD1   {PIO_PB4A_TWD1, PIOB, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT}
/** TWI1 clock pin */
#define PIN_TWI_TWCK1  {PIO_PB5A_TWCK1, PIOB, ID_PIOB, PIO_PERIPH_A,PIO_DEFAULT}
/** TWI1 pins */
#define PINS_TWI1      {PIN_TWI_TWD1, PIN_TWI_TWCK1}

/** USART0 pin RX */
#define PIN_USART0_RXD    {PIO_PB0C_RXD0, PIOB, ID_PIOB, PIO_PERIPH_C, PIO_DEFAULT}
/** USART0 pin TX */
#define PIN_USART0_TXD    {PIO_PB1C_TXD0, PIOB, ID_PIOB, PIO_PERIPH_C, PIO_DEFAULT}
/** USART0 pin CTS */
#define PIN_USART0_CTS    {PIO_PB2C_CTS0, PIOB, ID_PIOB, PIO_PERIPH_C, PIO_DEFAULT}
/** USART0 pin RTS */
#define PIN_USART0_RTS    {PIO_PB3C_RTS0, PIOB, ID_PIOB, PIO_PERIPH_C, PIO_DEFAULT}
/** USART0 pin SCK */
#define PIN_USART0_SCK    {PIO_PB13C_SCK0, PIOB, ID_PIOB, PIO_PERIPH_C,PIO_DEFAULT}

/** USART1 pin RX */
#define PIN_USART1_RXD    {PIO_PA21A_RXD1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** USART1 pin TX */
#define PIN_USART1_TXD    {1<<22, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** USART1 pin CTS */
#define PIN_USART1_CTS    {PIO_PA25A_CTS1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** USART1 pin RTS */
#define PIN_USART1_RTS    {PIO_PA24A_RTS1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
/** USART1 pin ENABLE */
#define PIN_USART1_EN     {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
/** USART1 pin SCK */
#define PIN_USART1_SCK    {PIO_PA23A_SCK1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}

/** USART2 pin RX */
#define PIN_USART2_RXD    {PIO_PD15B_RXD2, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** USART2 pin TX */
#define PIN_USART2_TXD    {PIO_PD16B_TXD2, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** USART2 pin CTS */
#define PIN_USART2_CTS    {PIO_PD19B_CTS2, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** USART2 pin RTS */
#define PIN_USART2_RTS    {PIO_PD18B_RTS2, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** USART2 pin SCK */
#define PIN_USART2_SCK    {PIO_PD17B_SCK2, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}

/** USB VBus monitoring pin definition. */
#define PIN_USB_VBUS    {PIO_PC16, PIOC, ID_PIOC, PIO_INPUT, PIO_DEFAULT}


/** NandFlash pins definition: OE. */
#define PIN_EBI_NANDOE   {PIO_PC9,  PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** NandFlash pins definition: WE. */
#define PIN_EBI_NANDWE   {PIO_PC10, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** NandFlash pins definition: CLE. */
#define PIN_EBI_NANDCLE  {PIO_PC17, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** NandFlash pins definition: ALE. */
#define PIN_EBI_NANDALE  {PIO_PC16, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** NandFlash pins definition: DATA. */
#define PIN_EBI_NANDIO   {0x000000FF, PIOC, ID_PIOC, PIO_PERIPH_A, PIO_PULLUP}
/** Nandflash chip enable pin definition. */
#define BOARD_NF_CE_PIN  {PIO_PC14, PIOC, ID_PIOC, PIO_OUTPUT_1, PIO_DEFAULT}
/** Nandflash ready/busy pin definition. */
#define BOARD_NF_RB_PIN  {0, 0, 0, 0, 0}

/** Nandflash controller peripheral pins definition. */
#define PINS_NANDFLASH   {PIN_EBI_NANDIO, BOARD_NF_CE_PIN, BOARD_NF_RB_PIN, \
		PIN_EBI_NANDOE, PIN_EBI_NANDWE, PIN_EBI_NANDCLE, PIN_EBI_NANDALE}

/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_usb "SAMV7_Xplained_Ultra - GMAC"
 */


/** PHY address */
#define BOARD_GMAC_PHY_ADDR             1
/** PHY Component */
#define BOARD_GMAC_PHY_COMP_KSZ8061RNB  1
/** Board GMAC power control - ALWAYS ON */
#define BOARD_GMAC_POWER_ALWAYS_ON
/** Board GMAC work mode - RMII/MII ( 1 / 0 ) */
#define BOARD_GMAC_MODE_RMII            1

/** The PIN list of PIO for GMAC */
#define BOARD_GMAC_PINS          { (PIO_PD0A_GTXCK | PIO_PD1A_GTXEN | PIO_PD2A_GTX0 | PIO_PD3A_GTX1 | PIO_PD4A_GRXDV | PIO_PD5A_GRX0 | PIO_PD6A_GRX1 | PIO_PD7A_GRXER | PIO_PD8A_GMDC | PIO_PD9A_GMDIO ), \
                                  PIOD, ID_PIOD, PIO_PERIPH_A, PIO_DEFAULT}, \
                                 {PIO_PC30, PIOC, ID_PIOC, PIO_INPUT,    PIO_PULLUP},\
                                 {PIO_PA29, PIOA, ID_PIOA, PIO_INPUT,    PIO_DEFAULT}

                                   /** The PIN list of PIO for GMAC */
#define BOARD_GMAC_RESET_PIN     {PIO_PC10, PIOC, ID_PIOC, PIO_OUTPUT_1,    PIO_PULLUP}

/** The runtime pin configure list for GMAC */
#define BOARD_GMAC_RUN_PINS BOARD_GMAC_PINS


#define PIN_ISI_D0   {PIO_PD22D_ISI_D0,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D1   {PIO_PD21D_ISI_D1,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D2   {PIO_PB3D_ISI_D2,  PIOB, ID_PIOB, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D3   {PIO_PA9B_ISI_D3,  PIOA, ID_PIOA, PIO_PERIPH_B, PIO_PULLUP}
#define PIN_ISI_D4   {PIO_PA5B_ISI_D4,  PIOA, ID_PIOA, PIO_PERIPH_B, PIO_PULLUP}
#define PIN_ISI_D5   {PIO_PD11D_ISI_D5,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D6   {PIO_PD12D_ISI_D6,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D7   {PIO_PA27D_ISI_D7,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D8   {PIO_PD27D_ISI_D8,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}
#define PIN_ISI_D9   {PIO_PD28D_ISI_D9,  PIOD, ID_PIOD, PIO_PERIPH_D, PIO_PULLUP}

#define BOARD_ISI_VSYNC     {PIO_PD25D_ISI_VSYNC, PIOD, ID_PIOD, PIO_PERIPH_D, PIO_DEFAULT}
#define BOARD_ISI_HSYNC     {PIO_PD24D_ISI_HSYNC, PIOD, ID_PIOD, PIO_PERIPH_D, PIO_DEFAULT}
#define BOARD_ISI_PCK       {PIO_PA24D_ISI_PCK, PIOA, ID_PIOA, PIO_PERIPH_D, PIO_DEFAULT}

#define BOARD_ISI_PINS  PIN_ISI_D0,PIN_ISI_D1,PIN_ISI_D2,PIN_ISI_D3,PIN_ISI_D4,\
                        PIN_ISI_D5,PIN_ISI_D6,PIN_ISI_D7,PIN_ISI_D8,PIN_ISI_D9,\
                        BOARD_ISI_VSYNC ,BOARD_ISI_HSYNC ,BOARD_ISI_PCK
/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_usb "SAMV7_Xplained_Ultra - USB device"
 *
 * \section Definitions
 * - \ref BOARD_USB_BMATTRIBUTES
 * - \ref CHIP_USB_UDP
 * - \ref CHIP_USB_PULLUP_INTERNAL
 * - \ref CHIP_USB_NUMENDPOINTS
 * - \ref CHIP_USB_ENDPOINTS_MAXPACKETSIZE
 * - \ref CHIP_USB_ENDPOINTS_BANKS
 */

/**
 * USB attributes configuration descriptor (bus or self powered,
 * remote wakeup)
 */
#define BOARD_USB_BMATTRIBUTES  USBConfigurationDescriptor_SELFPOWERED_RWAKEUP

/** Indicates chip has an UDP Full Speed. */
#define CHIP_USB_UDP

/** Indicates chip has an internal pull-up. */
#define CHIP_USB_PULLUP_INTERNAL

/** Number of USB endpoints */
#define CHIP_USB_NUMENDPOINTS 10

/** Endpoints max paxcket size */
#define CHIP_USB_ENDPOINTS_MAXPACKETSIZE(i)   ((i == 0) ? 64 : 1024)

/** Endpoints Number of Bank */
#define CHIP_USB_ENDPOINTS_BANKS(i) \
   ((i == 0) ? 1 : \
   ((i == 1) ? 3 : \
   ((i == 2) ? 3 : 2)))

/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_extcomp "SAMV7_Xplained_Ultra - External components"
 * This page lists the definitions related to external on-board components
 * located in the board.h file for the SAMV7_Xplained_Ultra.
 *
 * SD Card
 * - \ref BOARD_SD_PINS
 * - \ref BOARD_SD_PIN_CD
 *
 * LCD
 * - \ref BOARD_LCD_ILI9325
 * - \ref BOARD_LCD_PINS
 * - \ref BOARD_BACKLIGHT_PIN
 * - \ref BOARD_LCD_BASE
 * - \ref BOARD_LCD_RS
 * - \ref BOARD_LCD_WIDTH
 * - \ref BOARD_LCD_HEIGHT
 *
 * TouchScreen
 * - \ref BOARD_TSC_ADS7843
 * - \ref PIN_TCS_IRQ
 * - \ref PIN_TCS_BUSY
 * - \ref BOARD_TSC_SPI_BASE
 * - \ref BOARD_TSC_SPI_ID
 * - \ref BOARD_TSC_SPI_PINS
 * - \ref BOARD_TSC_NPCS
 * - \ref BOARD_TSC_NPCS_PIN
 *
 * SmartCard
 * - \ref SMARTCARD_CONNECT_PIN
 * - \ref PIN_ISO7816_RSTMC
 * - \ref PINS_ISO7816
 */


/** Indicates board has an ILI9325 external component to manage LCD. */
#define BOARD_LCD_ILI9488

     /** SPI MISO pin definition. */
#define LCD_SPI_MISO    {PIO_PD20B_SPI0_MISO, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SPI MOSI pin definition. */
#define LCD_SPI_MOSI    {PIO_PD21B_SPI0_MOSI, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SPI SPCK pin definition. */
#define LCD_SPI_SPCK    {PIO_PD22B_SPI0_SPCK, PIOD, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT}
/** SPI chip select pin definition. */
#define LCD_SPI_NPCS    {PIO_PD25B_SPI0_NPCS1, PIOD, ID_PIOD, PIO_PERIPH_B,PIO_DEFAULT}

/** LCD pins definition. */
#define BOARD_LCD_PINS  {LCD_SPI_MISO, LCD_SPI_MOSI, LCD_SPI_SPCK, LCD_SPI_NPCS}

/** Backlight pin definition. */

#define BOARD_LCD_BACKLIGHT_PIN   {PIO_PA0A_PWMC0_PWMH0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}

/** PWMC PWM0 pin definition: Output Low. */
#define LCD_PIN_RESET   {PIO_PD28, PIOD, ID_PIOD, PIO_OUTPUT_1, PIO_DEFAULT}

/** PWM channel for LED0 */
#define CHANNEL_PWM_LCD 0

/** Display width in pixels. */
#define BOARD_LCD_WIDTH             320
/** Display height in pixels. */
#define BOARD_LCD_HEIGHT            480


/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_mem "SAMV7_Xplained_Ultra - Memories"
 * This page lists definitions related to internal & external on-board memories.
 *
 * \section NandFlash
 * - \ref BOARD_NF_COMMAND_ADDR
 * - \ref BOARD_NF_ADDRESS_ADDR
 * - \ref BOARD_NF_DATA_ADDR
 *
 * \section NorFlash
 * - \ref BOARD_NORFLASH_ADDR
 * - \ref BOARD_NORFLASH_DFT_BUS_SIZE
 */

/** Address for transferring command bytes to the nandflash. */
#define BOARD_NF_COMMAND_ADDR   0x60400000
/** Address for transferring address bytes to the nandflash. */
#define BOARD_NF_ADDRESS_ADDR   0x60200000
/** Address for transferring data bytes to the nandflash. */
#define BOARD_NF_DATA_ADDR      0x60000000

/** Address for transferring command bytes to the norflash. */
#define BOARD_NORFLASH_ADDR     0x60000000
/** Default NOR bus size after power up reset */
#define BOARD_NORFLASH_DFT_BUS_SIZE 8

/*----------------------------------------------------------------------------*/
/**
 * \page samv7_Xplained_ultra_chipdef "SAMV7_Xplained_Ultra - Individual chip definition"
 * This page lists the definitions related to different chip's definition
 *
 * \section USART
 * - \ref BOARD_PIN_USART_RXD
 * - \ref BOARD_PIN_USART_TXD
 * - \ref BOARD_PIN_USART_CTS
 * - \ref BOARD_PIN_USART_RTS
 * - \ref BOARD_PIN_USART_EN
 * - \ref BOARD_USART_BASE
 * - \ref BOARD_ID_USART
 */

/** Rtc */
#define BOARD_RTC_ID              ID_RTC

/** TWI ID for QTouch application to use */
#define BOARD_ID_TWI_AT42         ID_TWI0
/** TWI Base for QTouch application to use */
#define BOARD_BASE_TWI_AT42       TWI0
/** TWI pins for QTouch application to use */
#define BOARD_PINS_TWI_AT42       PINS_TWI0

/** USART RX pin for application */
#define BOARD_PIN_USART_RXD        PIN_USART1_RXD
/** USART TX pin for application */
#define BOARD_PIN_USART_TXD        PIN_USART1_TXD
/** USART CTS pin for application */
#define BOARD_PIN_USART_CTS        PIN_USART1_CTS
/** USART RTS pin for application */
#define BOARD_PIN_USART_RTS        PIN_USART1_RTS
/** USART ENABLE pin for application */
#define BOARD_PIN_USART_EN         PIN_USART1_EN
/** USART Base for application */
#define BOARD_USART_BASE           USART1
/** USART ID for application */
#define BOARD_ID_USART             ID_USART1



/** MCI0 Card detect pin definition. (PE5) */
#define BOARD_MCI_PIN_CD       {PIO_PD18, PIOD, ID_PIOD, PIO_INPUT, PIO_PULLUP}

/** MCI0 Clock . */
#define BOARD_MCI_PIN_CK       {PIO_PA25D_MCCK, PIOA, ID_PIOA, PIO_PERIPH_D, PIO_DEFAULT}


/** MCI0 Solt A IO pins definition. (PC4-PC13) */
#define BOARD_MCI_PINS_SLOTA   {(PIO_PA30C_MCDA0 | PIO_PA31C_MCDA1 | PIO_PA26C_MCDA2 | PIO_PA27C_MCDA3 | PIO_PA28C_MCCDA),\
                                  PIOA, ID_PIOA, PIO_PERIPH_C, PIO_DEFAULT}


/** MCI pins that shall be configured to access the SD card. */
#define BOARD_SD_PINS    {BOARD_MCI_PINS_SLOTA, BOARD_MCI_PIN_CK}
/** MCI Card Detect pin. */
#define BOARD_SD_PIN_CD  BOARD_MCI_PIN_CD
 /** Total number of MCI interface */
#define BOARD_NUM_MCI           1

/** Total number of MCI interface */
#define BOARD_NUM_MCI           1


#define PINS_QSPI_IO         { (PIO_PA11A_QCS | PIO_PA13A_QIO0 | PIO_PA12A_QIO1 | PIO_PA17A_QIO2 | PIO_PA14A_QSCK), \
                               PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}

#define PINS_QSPI_IO3       { PIO_PD31A_QIO3, PIOD, ID_PIOD, PIO_PERIPH_A, PIO_DEFAULT}

#define PINS_QSPI           {PINS_QSPI_IO, PINS_QSPI_IO3}


#endif /* #ifndef _BOARD_H_ */