/*
 * Copyright (c) 2015, Freescale Semiconductor, Inc.
 * Copyright 2016-2017 NXP
 *
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 *
 * o Redistributions of source code must retain the above copyright notice, this list
 *   of conditions and the following disclaimer.
 *
 * o Redistributions in binary form must reproduce the above copyright notice, this
 *   list of conditions and the following disclaimer in the documentation and/or
 *   other materials provided with the distribution.
 *
 * o Neither the name of Freescale Semiconductor, Inc. nor the names of its
 *   contributors may be used to endorse or promote products derived from this
 *   software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

/*
 * How to setup clock using clock driver functions:
 *
 * 1. CLOCK_SetSimSafeDivs, to make sure core clock, bus clock, flexbus clock
 *    and flash clock are in allowed range during clock mode switch.
 *
 * 2. Call CLOCK_Osc0Init to setup OSC clock, if it is used in target mode.
 *
 * 3. Set MCG configuration, MCG includes three parts: FLL clock, PLL clock and
 *    internal reference clock(MCGIRCLK). Follow the steps to setup:
 *
 *    1). Call CLOCK_BootToXxxMode to set MCG to target mode.
 *
 *    2). If target mode is FBI/BLPI/PBI mode, the MCGIRCLK has been configured
 *        correctly. For other modes, need to call CLOCK_SetInternalRefClkConfig
 *        explicitly to setup MCGIRCLK.
 *
 *    3). Don't need to configure FLL explicitly, because if target mode is FLL
 *        mode, then FLL has been configured by the function CLOCK_BootToXxxMode,
 *        if the target mode is not FLL mode, the FLL is disabled.
 *
 *    4). If target mode is PEE/PBE/PEI/PBI mode, then the related PLL has been
 *        setup by CLOCK_BootToXxxMode. In FBE/FBI/FEE/FBE mode, the PLL could
 *        be enabled independently, call CLOCK_EnablePll0 explicitly in this case.
 *
 * 4. Call CLOCK_SetSimConfig to set the clock configuration in SIM.
 */

/* TEXT BELOW IS USED AS SETTING FOR THE CLOCKS TOOL *****************************
!!ClocksProfile
product: Clocks v1.0
processor: MKW41Z512xxx4
package_id: MKW41Z512VHT4
mcu_data: ksdk2_0
processor_version: 0.1.28
board: FRDM-KW41Z
 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR THE CLOCKS TOOL **/

#include "fsl_rtc.h"
#include "clock_config.h"

/*******************************************************************************
 * Definitions
 ******************************************************************************/
#define RTC_OSC_CAP_LOAD_0PF                            0x0U  /*!< RTC oscillator capacity load: 0pF */
#define SIM_LPUART_CLK_SEL_OSCERCLK_CLK                   2U  /*!< LPUART clock select: OSCERCLK clock */
#define SIM_OSC32KSEL_OSC32KCLK_CLK                       0U  /*!< OSC32KSEL select: OSC32KCLK clock */
#define SIM_TPM_CLK_SEL_OSCERCLK_CLK                      2U  /*!< TPM clock select: OSCERCLK clock */

/*******************************************************************************
 * Variables
 ******************************************************************************/
/* System clock frequency. */
extern uint32_t SystemCoreClock;

/*******************************************************************************
 * Code
 ******************************************************************************/
/*FUNCTION**********************************************************************
 *
 * Function Name : CLOCK_CONFIG_FllStableDelay
 * Description   : This function is used to delay for FLL stable.
 *
 *END**************************************************************************/
static void CLOCK_CONFIG_FllStableDelay(void)
{
    uint32_t i = 30000U;

    while (i--)
    {
        __NOP();
    }
}

/*FUNCTION**********************************************************************
 *
 * Function Name : CLOCK_CONFIG_SetRtcClock
 * Description   : This function is used to configuring RTC clock
 *
 *END**************************************************************************/
static void CLOCK_CONFIG_SetRtcClock()
{
    /* RTC clock gate enable */
    CLOCK_EnableClock(kCLOCK_Rtc0);

    /* Set RTC_TSR if there is fault value in RTC */
    if (RTC->SR & RTC_SR_TIF_MASK)
    {
        RTC -> TSR = RTC -> TSR;
    }

    /* RTC clock gate disable */
    CLOCK_DisableClock(kCLOCK_Rtc0);
}

/*FUNCTION**********************************************************************
 *
 * Function Name : CLOCK_CONFIG_EnableRtcOsc
 * Description   : This function is used to enabling RTC oscillator
 * Param capLoad : Oscillator capacity load
 *
 *END**************************************************************************/
static void CLOCK_CONFIG_EnableRtcOsc(uint32_t capLoad)
{
    /* RTC clock gate enable */
    CLOCK_EnableClock(kCLOCK_Rtc0);

    if ((RTC->CR & RTC_CR_OSCE_MASK) == 0u)   /* Only if the Rtc oscillator is not already enabled */
    {
        /* Set the specified capacitor configuration for the RTC oscillator */
        RTC_SetOscCapLoad(RTC, capLoad);
        /* Enable the RTC 32KHz oscillator */
        RTC->CR |= RTC_CR_OSCE_MASK;
    }

    /* RTC clock gate disable */
    CLOCK_DisableClock(kCLOCK_Rtc0);
    CLOCK_SetXtal32Freq(32768);
}

/*FUNCTION**********************************************************************
 *
 * Function Name : BOARD_RfOscInit
 * Description   : This function is used to setup Ref oscillator for KW40_512.
 *
 *END**************************************************************************/
void BOARD_RfOscInit(void)
{
    uint32_t tempTrim;
    uint8_t revId;

    /* Obtain REV ID from SIM */
    revId = (uint8_t)((uint32_t)(SIM->SDID & SIM_SDID_REVID_MASK) >> SIM_SDID_REVID_SHIFT);

    if (0 == revId)
    {
        tempTrim = RSIM->ANA_TRIM;
        RSIM->ANA_TRIM |= RSIM_ANA_TRIM_BB_LDO_XO_TRIM_MASK;            /* Set max trim for BB LDO for XO */
    }/* Workaround for Rev 1.0 XTAL startup and ADC analog diagnostics circuitry */

    /* Turn on clocks for the XCVR */

    /* Enable RF OSC in RSIM and wait for ready */
    RSIM->CONTROL = ((RSIM->CONTROL & ~RSIM_CONTROL_RF_OSC_EN_MASK) | RSIM_CONTROL_RF_OSC_EN(1));

    /* ERR010224 */
    RSIM->RF_OSC_CTRL |=
        RSIM_RF_OSC_CTRL_RADIO_EXT_OSC_OVRD_EN_MASK;   /* Prevent XTAL_OUT_EN from generating XTAL_OUT request */

    while ((RSIM->CONTROL & RSIM_CONTROL_RF_OSC_READY_MASK) == 0);      /* Wait for RF_OSC_READY */

    if (0 == revId)
    {
        SIM->SCGC5 |= SIM_SCGC5_PHYDIG_MASK;
        XCVR_TSM->OVRD0 |= XCVR_TSM_OVRD0_BB_LDO_ADCDAC_EN_OVRD_EN_MASK |
                           XCVR_TSM_OVRD0_BB_LDO_ADCDAC_EN_OVRD_MASK; /* Force ADC DAC LDO on to prevent BGAP failure */

        RSIM->ANA_TRIM = tempTrim;                                      /* Reset LDO trim settings */
    }/* Workaround for Rev 1.0 XTAL startup and ADC analog diagnostics circuitry */

}

/*FUNCTION**********************************************************************
 *
 * Function Name : BOARD_InitOsc0
 * Description   : This function is used to setup MCG OSC with Ref oscillator for KW40_512.
 *
 *END**************************************************************************/
void BOARD_InitOsc0(void)
{
    const osc_config_t oscConfig =
    {
        .freq = BOARD_XTAL0_CLK_HZ, .workMode = kOSC_ModeExt,
    };

    /* Initializes OSC0 according to previous configuration to meet Ref OSC needs. */
    CLOCK_InitOsc0(&oscConfig);

    /* Passing the XTAL0 frequency to clock driver. */
    CLOCK_SetXtal0Freq(BOARD_XTAL0_CLK_HZ);
}

/*******************************************************************************
 ********************** Configuration BOARD_BootClockRUN ***********************
 ******************************************************************************/
/* TEXT BELOW IS USED AS SETTING FOR THE CLOCKS TOOL *****************************
!!Configuration
name: BOARD_BootClockRUN
outputs:
- {id: Bus_clock.outFreq, value: 23.986176 MHz}
- {id: Core_clock.outFreq, value: 47.972352 MHz}
- {id: ERCLK32K.outFreq, value: 32.768 kHz}
- {id: Flash_clock.outFreq, value: 23.986176 MHz}
- {id: LPO_clock.outFreq, value: 1 kHz}
- {id: LPUART0CLK.outFreq, value: 32 MHz}
- {id: MCGFLLCLK.outFreq, value: 47.972352 MHz}
- {id: MCGIRCLK.outFreq, value: 32.768 kHz}
- {id: OSCERCLK.outFreq, value: 32 MHz}
- {id: System_clock.outFreq, value: 47.972352 MHz}
- {id: TPMCLK.outFreq, value: 32 MHz}
settings:
- {id: MCGMode, value: FEE}
- {id: LPUART0ClkConfig, value: 'yes'}
- {id: MCG.FCRDIV.scale, value: '1'}
- {id: MCG.FLL_mul.scale, value: '1464'}
- {id: MCG.IREFS.sel, value: MCG.FRDIV}
- {id: MCG.OSCSEL.sel, value: RTC_32K.OSCCLK32K}
- {id: MCG_C1_IRCLKEN_CFG, value: Enabled}
- {id: RTC_CR_OSCE_CFG, value: Oscillator_enabled}
- {id: SIM.LPUART0SRCSEL.sel, value: REFOSC.OSCCLK}
- {id: SIM.TPMSRCSEL.sel, value: REFOSC.OSCCLK}
- {id: TPMClkConfig, value: 'yes'}
sources:
- {id: REFOSC.OSC.outFreq, value: 32 MHz, enabled: true}
- {id: RTC_32K.OSC32kHz.outFreq, value: 32.768 kHz, enabled: true}
 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR THE CLOCKS TOOL **/

/*******************************************************************************
 * Variables for BOARD_BootClockRUN configuration
 ******************************************************************************/
const mcg_config_t mcgConfig_BOARD_BootClockRUN =
{
    .mcgMode = kMCG_ModeFEE,                  /* FEE - FLL Engaged External */
    .irclkEnableMode = kMCG_IrclkEnable,      /* MCGIRCLK enabled, MCGIRCLK disabled in STOP mode */
    .ircs = kMCG_IrcSlow,                     /* Slow internal reference clock selected */
    .fcrdiv = 0x0U,                           /* Fast IRC divider: divided by 1 */
    .frdiv = 0x0U,                            /* FLL reference clock divider: divided by 1 */
    .drs = kMCG_DrsMid,                       /* Mid frequency range */
    .dmx32 = kMCG_Dmx32Fine,                  /* DCO is fine-tuned for maximum frequency with 32.768 kHz reference */
    .oscsel = kMCG_OscselRtc,                 /* Selects 32 kHz RTC Oscillator */
};
const sim_clock_config_t simConfig_BOARD_BootClockRUN =
{
    .er32kSrc = SIM_OSC32KSEL_OSC32KCLK_CLK,  /* OSC32KSEL select: OSC32KCLK clock */
    .clkdiv1 = 0x10000U,                      /* SIM_CLKDIV1 - OUTDIV1: /1, OUTDIV4: /2 */
};

/*******************************************************************************
 * Code for BOARD_BootClockRUN configuration
 ******************************************************************************/
void BOARD_BootClockRUN(void)
{
    /* Setup the reference oscillator. */
    BOARD_RfOscInit();
    /* Set the system clock dividers in SIM to safe value. */
    CLOCK_SetSimSafeDivs();
    /* Enable RTC oscillator. */
    CLOCK_CONFIG_EnableRtcOsc(RTC_OSC_CAP_LOAD_0PF);
    /* Initializes OSC0 according to Ref OSC needs. */
    BOARD_InitOsc0();
    /* Set MCG to FEE mode. */
    CLOCK_BootToFeeMode(mcgConfig_BOARD_BootClockRUN.oscsel,
                        mcgConfig_BOARD_BootClockRUN.frdiv,
                        mcgConfig_BOARD_BootClockRUN.dmx32,
                        mcgConfig_BOARD_BootClockRUN.drs,
                        CLOCK_CONFIG_FllStableDelay);
    /* Configure the Internal Reference clock (MCGIRCLK). */
    CLOCK_SetInternalRefClkConfig(mcgConfig_BOARD_BootClockRUN.irclkEnableMode,
                                  mcgConfig_BOARD_BootClockRUN.ircs,
                                  mcgConfig_BOARD_BootClockRUN.fcrdiv);
    /* Set the clock configuration in SIM module. */
    CLOCK_SetSimConfig(&simConfig_BOARD_BootClockRUN);
    /* Configure RTC clock. */
    CLOCK_CONFIG_SetRtcClock();
    /* Set SystemCoreClock variable. */
    SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK;
    /* Set LPUART0 clock source. */
    CLOCK_SetLpuartClock(SIM_LPUART_CLK_SEL_OSCERCLK_CLK);
    /* Set TPM clock source. */
    CLOCK_SetTpmClock(SIM_TPM_CLK_SEL_OSCERCLK_CLK);
}