| /****************************************************************************** |
| * Filename: rf_ble_mailbox.h |
| * Revised: $ $ |
| * Revision: $ $ |
| * |
| * Description: Definitions for BLE interface |
| * |
| * Copyright (c) 2015 - 2016, Texas Instruments Incorporated |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are met: |
| * |
| * 1) Redistributions of source code must retain the above copyright notice, |
| * this list of conditions and the following disclaimer. |
| * |
| * 2) Redistributions in binary form must reproduce the above copyright notice, |
| * this list of conditions and the following disclaimer in the documentation |
| * and/or other materials provided with the distribution. |
| * |
| * 3) Neither the name of the ORGANIZATION nor the names of its contributors may |
| * be used to endorse or promote products derived from this software without |
| * specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
| * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
| * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE |
| * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
| * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
| * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS |
| * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN |
| * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) |
| * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
| * POSSIBILITY OF SUCH DAMAGE. |
| * |
| ******************************************************************************/ |
| |
| #ifndef _BLE_MAILBOX_H |
| #define _BLE_MAILBOX_H |
| |
| /// \name Radio operation status |
| ///@{ |
| /// \name Operation finished normally |
| ///@{ |
| #define BLE_DONE_OK 0x1400 ///< Operation ended normally |
| #define BLE_DONE_RXTIMEOUT 0x1401 ///< Timeout of first Rx of slave operation or end of scan window |
| #define BLE_DONE_NOSYNC 0x1402 ///< Timeout of subsequent Rx |
| #define BLE_DONE_RXERR 0x1403 ///< Operation ended because of receive error (CRC or other) |
| #define BLE_DONE_CONNECT 0x1404 ///< CONNECT_REQ received or transmitted |
| #define BLE_DONE_MAXNACK 0x1405 ///< Maximum number of retransmissions exceeded |
| #define BLE_DONE_ENDED 0x1406 ///< Operation stopped after end trigger |
| #define BLE_DONE_ABORT 0x1407 ///< Operation aborted by command |
| #define BLE_DONE_STOPPED 0x1408 ///< Operation stopped after stop command |
| ///@} |
| /// \name Operation finished with error |
| ///@{ |
| #define BLE_ERROR_PAR 0x1800 ///< Illegal parameter |
| #define BLE_ERROR_RXBUF 0x1801 ///< No available Rx buffer (Advertiser, Scanner, Initiator) |
| #define BLE_ERROR_NO_SETUP 0x1802 ///< Operation using Rx or Tx attemted when not in BLE mode |
| #define BLE_ERROR_NO_FS 0x1803 ///< Operation using Rx or Tx attemted without frequency synth configured |
| #define BLE_ERROR_SYNTH_PROG 0x1804 ///< Synthesizer programming failed to complete on time |
| #define BLE_ERROR_RXOVF 0x1805 ///< Receiver overflowed during operation |
| #define BLE_ERROR_TXUNF 0x1806 ///< Transmitter underflowed during operation |
| ///@} |
| ///@} |
| |
| #endif |
