u-boot-imx/arch/arm/mach-uniphier/ph1-ld4/pll_init.c

/*
 * Copyright (C) 2011-2014 Panasonic Corporation
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/io.h>
#include <mach/sc-regs.h>
#include <mach/sg-regs.h>

#undef DPLL_SSC_RATE_1PER

static void dpll_init(void)
{
	u32 tmp;

	/*
	 * Set Frequency
	 * Set 0xc(1600MHz)/0xd(1333MHz)/0xe(1066MHz)
	 * to FOUT (DPLLCTRL.bit[29:20])
	 */
	tmp = readl(SC_DPLLCTRL);
	tmp &= ~0x000f0000;
#if CONFIG_DDR_FREQ == 1600
	tmp |= 0x000c0000;
#elif CONFIG_DDR_FREQ == 1333
	tmp |= 0x000d0000;
#else
# error "Unknown frequency"
#endif

#if defined(DPLL_SSC_RATE_1PER)
	tmp &= ~SC_DPLLCTRL_SSC_RATE;
#else
	tmp |= SC_DPLLCTRL_SSC_RATE;
#endif
	writel(tmp, SC_DPLLCTRL);

	tmp = readl(SC_DPLLCTRL2);
	tmp |= SC_DPLLCTRL2_NRSTDS;
	writel(tmp, SC_DPLLCTRL2);
}

static void upll_init(void)
{
	u32 tmp, clk_mode_upll, clk_mode_axosel;

	tmp = readl(SG_PINMON0);
	clk_mode_upll   = tmp & SG_PINMON0_CLK_MODE_UPLLSRC_MASK;
	clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;

	/* set 0 to SNRT(UPLLCTRL.bit28) and K_LD(UPLLCTRL.bit[27]) */
	tmp = readl(SC_UPLLCTRL);
	tmp &= ~0x18000000;
	writel(tmp, SC_UPLLCTRL);

	if (clk_mode_upll == SG_PINMON0_CLK_MODE_UPLLSRC_DEFAULT) {
		if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U ||
		    clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A) {
			/* AXO: 25MHz */
			tmp &= ~0x07ffffff;
			tmp |= 0x0228f5c0;
		} else {
			/* AXO: default 24.576MHz */
			tmp &= ~0x07ffffff;
			tmp |= 0x02328000;
		}
	}

	writel(tmp, SC_UPLLCTRL);

	/* set 1 to K_LD(UPLLCTRL.bit[27]) */
	tmp |= 0x08000000;
	writel(tmp, SC_UPLLCTRL);

	/* wait 10 usec */
	udelay(10);

	/* set 1 to SNRT(UPLLCTRL.bit[28]) */
	tmp |= 0x10000000;
	writel(tmp, SC_UPLLCTRL);
}

static void vpll_init(void)
{
	u32 tmp, clk_mode_axosel;

	tmp = readl(SG_PINMON0);
	clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;

	/* set 1 to VPLA27WP and VPLA27WP */
	tmp = readl(SC_VPLL27ACTRL);
	tmp |= 0x00000001;
	writel(tmp, SC_VPLL27ACTRL);
	tmp = readl(SC_VPLL27BCTRL);
	tmp |= 0x00000001;
	writel(tmp, SC_VPLL27BCTRL);

	/* Set 0 to VPLA_K_LD and VPLB_K_LD */
	tmp = readl(SC_VPLL27ACTRL3);
	tmp &= ~0x10000000;
	writel(tmp, SC_VPLL27ACTRL3);
	tmp = readl(SC_VPLL27BCTRL3);
	tmp &= ~0x10000000;
	writel(tmp, SC_VPLL27BCTRL3);

	/* Set 0 to VPLA_SNRST and VPLB_SNRST */
	tmp = readl(SC_VPLL27ACTRL2);
	tmp &= ~0x10000000;
	writel(tmp, SC_VPLL27ACTRL2);
	tmp = readl(SC_VPLL27BCTRL2);
	tmp &= ~0x10000000;
	writel(tmp, SC_VPLL27BCTRL2);

	/* Set 0x20 to VPLA_SNRST and VPLB_SNRST */
	tmp = readl(SC_VPLL27ACTRL2);
	tmp &= ~0x0000007f;
	tmp |= 0x00000020;
	writel(tmp, SC_VPLL27ACTRL2);
	tmp = readl(SC_VPLL27BCTRL2);
	tmp &= ~0x0000007f;
	tmp |= 0x00000020;
	writel(tmp, SC_VPLL27BCTRL2);

	if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U ||
	    clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A) {
		/* AXO: 25MHz */
		tmp = readl(SC_VPLL27ACTRL3);
		tmp &= ~0x000fffff;
		tmp |= 0x00066664;
		writel(tmp, SC_VPLL27ACTRL3);
		tmp = readl(SC_VPLL27BCTRL3);
		tmp &= ~0x000fffff;
		tmp |= 0x00066664;
		writel(tmp, SC_VPLL27BCTRL3);
	} else {
		/* AXO: default 24.576MHz */
		tmp = readl(SC_VPLL27ACTRL3);
		tmp &= ~0x000fffff;
		tmp |= 0x000f5800;
		writel(tmp, SC_VPLL27ACTRL3);
		tmp = readl(SC_VPLL27BCTRL3);
		tmp &= ~0x000fffff;
		tmp |= 0x000f5800;
		writel(tmp, SC_VPLL27BCTRL3);
	}

	/* Set 1 to VPLA_K_LD and VPLB_K_LD */
	tmp = readl(SC_VPLL27ACTRL3);
	tmp |= 0x10000000;
	writel(tmp, SC_VPLL27ACTRL3);
	tmp = readl(SC_VPLL27BCTRL3);
	tmp |= 0x10000000;
	writel(tmp, SC_VPLL27BCTRL3);

	/* wait 10 usec */
	udelay(10);

	/* Set 0 to VPLA_SNRST and VPLB_SNRST */
	tmp = readl(SC_VPLL27ACTRL2);
	tmp |= 0x10000000;
	writel(tmp, SC_VPLL27ACTRL2);
	tmp = readl(SC_VPLL27BCTRL2);
	tmp |= 0x10000000;
	writel(tmp, SC_VPLL27BCTRL2);

	/* set 0 to VPLA27WP and VPLA27WP */
	tmp = readl(SC_VPLL27ACTRL);
	tmp &= ~0x00000001;
	writel(tmp, SC_VPLL27ACTRL);
	tmp = readl(SC_VPLL27BCTRL);
	tmp |= ~0x00000001;
	writel(tmp, SC_VPLL27BCTRL);
}

void pll_init(void)
{
	dpll_init();
	upll_init();
	vpll_init();

	/*
	 * Wait 500 usec until dpll get stable
	 * We wait 10 usec in upll_init() and vpll_init()
	 * so 20 usec can be saved here.
	 */
	udelay(480);
}