/*
 * Manroland mucmc52 board Device Tree Source
 *
 * Copyright (C) 2009 DENX Software Engineering GmbH
 * Heiko Schocher <hs@denx.de>
 * Copyright 2006-2007 Secret Lab Technologies Ltd.
 *
 * This program is free software; you can redistribute  it and/or modify it
 * under  the terms of  the GNU General  Public License as published by the
 * Free Software Foundation;  either version 2 of the  License, or (at your
 * option) any later version.
 */

/dts-v1/;

/ {
	model = "manroland,mucmc52";
	compatible = "manroland,mucmc52";
	#address-cells = <1>;
	#size-cells = <1>;
	interrupt-parent = <&mpc5200_pic>;

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		PowerPC,5200@0 {
			device_type = "cpu";
			reg = <0>;
			d-cache-line-size = <32>;
			i-cache-line-size = <32>;
			d-cache-size = <0x4000>;	// L1, 16K
			i-cache-size = <0x4000>;	// L1, 16K
			timebase-frequency = <0>;	// from bootloader
			bus-frequency = <0>;		// from bootloader
			clock-frequency = <0>;		// from bootloader
		};
	};

	memory {
		device_type = "memory";
		reg = <0x00000000 0x04000000>;	// 64MB
	};

	soc5200@f0000000 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "fsl,mpc5200b-immr";
		ranges = <0 0xf0000000 0x0000c000>;
		reg = <0xf0000000 0x00000100>;
		bus-frequency = <0>;		// from bootloader
		system-frequency = <0>;		// from bootloader

		cdm@200 {
			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
			reg = <0x200 0x38>;
		};

		mpc5200_pic: interrupt-controller@500 {
			// 5200 interrupts are encoded into two levels;
			interrupt-controller;
			#interrupt-cells = <3>;
			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
			reg = <0x500 0x80>;
		};

		gpt0: timer@600 {	// GPT 0 in GPIO mode
			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
			reg = <0x600 0x10>;
			interrupts = <1 9 0>;
			gpio-controller;
			#gpio-cells = <2>;
		};

		gpt1: timer@610 {	// General Purpose Timer in GPIO mode
			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
			reg = <0x610 0x10>;
			interrupts = <1 10 0>;
			gpio-controller;
			#gpio-cells = <2>;
		};

		gpt2: timer@620 {	// General Purpose Timer in GPIO mode
			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
			reg = <0x620 0x10>;
			interrupts = <1 11 0>;
			gpio-controller;
			#gpio-cells = <2>;
		};

		gpt3: timer@630 {	// General Purpose Timer in GPIO mode
			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
			reg = <0x630 0x10>;
			interrupts = <1 12 0>;
			gpio-controller;
			#gpio-cells = <2>;
		};

		gpio_simple: gpio@b00 {
			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
			reg = <0xb00 0x40>;
			interrupts = <1 7 0>;
			gpio-controller;
			#gpio-cells = <2>;
		};

		gpio_wkup: gpio@c00 {
			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
			reg = <0xc00 0x40>;
			interrupts = <1 8 0 0 3 0>;
			gpio-controller;
			#gpio-cells = <2>;
		};

		dma-controller@1200 {
			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
			reg = <0x1200 0x80>;
			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
			              3 4 0  3 5 0  3 6 0  3 7 0
			              3 8 0  3 9 0  3 10 0  3 11 0
			              3 12 0  3 13 0  3 14 0  3 15 0>;
		};

		xlb@1f00 {
			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
			reg = <0x1f00 0x100>;
		};

		serial@2000 { /* PSC1 in UART mode */
			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
			reg = <0x2000 0x100>;
			interrupts = <2 1 0>;
		};

		serial@2200 { /* PSC2 in UART mode */
			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
			reg = <0x2200 0x100>;
			interrupts = <2 2 0>;
		};

		serial@2c00 { /* PSC6 in UART mode */
			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
			reg = <0x2c00 0x100>;
			interrupts = <2 4 0>;
		};

		ethernet@3000 {
			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
			reg = <0x3000 0x400>;
			local-mac-address = [ 00 00 00 00 00 00 ];
			interrupts = <2 5 0>;
			phy-handle = <&phy0>;
		};

		mdio@3000 {
			#address-cells = <1>;
			#size-cells = <0>;
			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
			reg = <0x3000 0x400>; 	// fec range, since we need to setup fec interrupts
			interrupts = <2 5 0>; 	// these are for "mii command finished", not link changes & co.

			phy0: ethernet-phy@0 {
				compatible = "intel,lxt971";
				reg = <0>;
			};
		};

		ata@3a00 {
			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
			reg = <0x3a00 0x100>;
			interrupts = <2 7 0>;
		};

		i2c@3d40 {
			#address-cells = <1>;
			#size-cells = <0>;
			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
			reg = <0x3d40 0x40>;
			interrupts = <2 16 0>;
			hwmon@2c {
				compatible = "ad,adm9240";
				reg = <0x2c>;
			};
			rtc@51 {
				compatible = "nxp,pcf8563";
				reg = <0x51>;
			};
		};

		sram@8000 {
			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
			reg = <0x8000 0x4000>;
		};
	};

	pci@f0000d00 {
		#interrupt-cells = <1>;
		#size-cells = <2>;
		#address-cells = <3>;
		device_type = "pci";
		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
		reg = <0xf0000d00 0x100>;
		interrupt-map-mask = <0xf800 0 0 7>;
		interrupt-map = <
				/* IDSEL 0x10 */
				0x8000 0 0 1 &mpc5200_pic 0 3 3
				0x8000 0 0 2 &mpc5200_pic 0 3 3
				0x8000 0 0 3 &mpc5200_pic 0 2 3
				0x8000 0 0 4 &mpc5200_pic 0 1 3
				>;
		clock-frequency = <0>; // From boot loader
		interrupts = <2 8 0 2 9 0 2 10 0>;
		bus-range = <0 0>;
		ranges = <0x42000000 0 0x60000000 0x60000000 0 0x10000000
			  0x02000000 0 0x90000000 0x90000000 0 0x10000000
			  0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
	};

	localbus {
		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";

		#address-cells = <2>;
		#size-cells = <1>;

		ranges = <0 0 0xff800000 0x00800000
			  1 0 0x80000000 0x00800000
			  3 0 0x80000000 0x00800000>;

		flash@0,0 {
			compatible = "cfi-flash";
			reg = <0 0 0x00800000>;
			bank-width = <4>;
			device-width = <2>;
			#size-cells = <1>;
			#address-cells = <1>;
			partition@0 {
				label = "DTS";
				reg = <0x0 0x00100000>;
			};
			partition@100000 {
				label = "Kernel";
				reg = <0x100000 0x00200000>;
			};
			partition@300000 {
				label = "RootFS";
				reg = <0x00300000 0x00200000>;
			};
			partition@500000 {
				label = "user";
				reg = <0x00500000 0x00200000>;
			};
			partition@700000 {
				label = "U-Boot";
				reg = <0x00700000 0x00040000>;
			};
			partition@740000 {
				label = "Env";
				reg = <0x00740000 0x00020000>;
			};
			partition@760000 {
				label = "red. Env";
				reg = <0x00760000 0x00020000>;
			};
			partition@780000 {
				label = "reserve";
				reg = <0x00780000 0x00080000>;
			};
		};

		simple100: gpio-controller-100@3,600100 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600100 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple104: gpio-controller-104@3,600104 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600104 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple200: gpio-controller-200@3,600200 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600200 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple201: gpio-controller-201@3,600201 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600201 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple202: gpio-controller-202@3,600202 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600202 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple203: gpio-controller-203@3,600203 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600203 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple204: gpio-controller-204@3,600204 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600204 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple206: gpio-controller-206@3,600206 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600206 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple207: gpio-controller-207@3,600207 {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x00600207 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};
		simple20f: gpio-controller-20f@3,60020f {
			compatible = "manroland,mucmc52-aux-gpio";
			reg = <3 0x0060020f 0x1>;
			gpio-controller;
			#gpio-cells = <2>;
		};

	};
};