/*
 * (C) Copyright 2000
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC850		1	/* This is a MPC850 CPU		*/
#define CONFIG_ETX094		1	/* ...on a ETX_094 board	*/

#define	CONFIG_SYS_TEXT_BASE	0x40000000

#define	CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
#undef	CONFIG_8xx_CONS_SMC2
#undef	CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE		57600
#if 0
#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
#else
#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
#endif

#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */

#define CONFIG_BOARD_TYPES	1	/* support board types		*/

#define	CONFIG_FLASH_16BIT		/* for board with 16bit wide flash	*/
#undef	SB_ETX094			/* only for SB-Board with 16MB SDRAM	*/
#define	CONFIG_BOOTP_RANDOM_DELAY	/* graceful BOOTP recovery mode		*/

#define CONFIG_ETHADDR 08:00:06:00:00:00

#ifdef	CONFIG_ETHADDR
#define CONFIG_OVERWRITE_ETHADDR_ONCE 1	/* default MAC can be overwritten once	*/
#endif

#undef	CONFIG_BOOTARGS
#define CONFIG_RAMBOOTCOMMAND							\
	"bootp; "								\
	"setenv bootargs root=/dev/ram rw ramdisk_size=4690 "			\
	"U-Boot_version=U-Boot-1.0.x-Date "					\
	"panic=1 "								\
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
	"bootm"
#define CONFIG_NFSBOOTCOMMAND							\
	"bootp; "								\
	"setenv bootargs root=/dev/nfs rw nfsroot=${nfsip}:${rootpath} "	\
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
	"bootm"
#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

#define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/

#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>


/*
 * Miscellaneous configurable options
 */
#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define	CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
#if defined(CONFIG_CMD_KGDB)
#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x0300000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0700000	/* 3 ... 7 MB in DRAM	*/

#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/

#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/*-----------------------------------------------------------------------
 * Internal Memory Mapped Register
 */
#define CONFIG_SYS_IMMR		0xFFF00000

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define	CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		0x40000000
#ifdef	DEBUG
#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#else
#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#endif
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	35	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/

#define	CONFIG_ENV_IS_IN_FLASH	1
#ifdef CONFIG_FLASH_16BIT
#define CONFIG_ENV_OFFSET		0x8000	/* Offset   of Environment Sector	*/
#define	CONFIG_ENV_SIZE		0x8000	/* Total Size of Environment Sector	*/
#else
#define CONFIG_ENV_OFFSET		0x8000	/* Offset   of Environment Sector	*/
#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
#endif

/*-----------------------------------------------------------------------
 * Hardware Information Block
 */
#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
#endif

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control				11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 */
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif	/* CONFIG_WATCHDOG */

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration				11-6
 *-----------------------------------------------------------------------
 * PCMCIA config., multi-function pin tri-state
 */
#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)

/*-----------------------------------------------------------------------
 * TBSCR - Time Base Status and Control				11-26
 *-----------------------------------------------------------------------
 * Clear Reference Interrupt Status, Timebase freezing enabled
 */
#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

/*-----------------------------------------------------------------------
 * RTCSC - Real-Time Clock Status and Control Register		11-27
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control		11-31
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 */
#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)

/*-----------------------------------------------------------------------
 * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
 *-----------------------------------------------------------------------
 * Reset PLL lock status sticky bit, timer expired status bit and timer
 * interrupt status bit - leave PLL multiplication factor unchanged !
 */
#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)

/*-----------------------------------------------------------------------
 * SCCR - System Clock and reset Control Register		15-27
 *-----------------------------------------------------------------------
 * Set clock output, timebase and RTC source and divider,
 * power management and some other internal clocks
 */
#define SCCR_MASK	SCCR_EBDF11
#define CONFIG_SYS_SCCR	(SCCR_TBS     | \
			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
			 SCCR_DFALCD00)

/*-----------------------------------------------------------------------
 * PCMCIA stuff
 *-----------------------------------------------------------------------
 *
 */
#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )

/*-----------------------------------------------------------------------
 *
 *-----------------------------------------------------------------------
 *
 */
#define CONFIG_SYS_DER	0

/*
 * Init Memory Controller:
 *
 * BR0/1 and OR0/1 (FLASH)
 */

#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/

/* used to re-map FLASH both when starting from SRAM or FLASH:
 * restrict access enough to keep SRAM working (if any)
 * but not too much to meddle with FLASH accesses
 */
#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */

/* FLASH timing: ACS = 11, TRLX = 1, CSNT = 0, SCY = 2, EHTR = 0	*/
#define CONFIG_SYS_OR_TIMING_FLASH    (OR_ACS_DIV2 | OR_BI | \
			       OR_SCY_2_CLK | OR_TRLX )

#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)

#ifdef CONFIG_FLASH_16BIT	/* 16 bit data port */
#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16)
#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16)
#else				/* 32 bit data port */
#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_32)
#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V | BR_PS_32)
#endif	/* CONFIG_FLASH_16BIT */

#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM

/*
 * BR2/3 and OR2/3 (SDRAM)
 *
 */
#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/

/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00

#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

#define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

/*
 * Memory Periodic Timer Prescaler
 */

/* periodic timer for refresh */
#define CONFIG_SYS_MAMR_PTA	23		/* start with divider for 100 MHz	*/

/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

/*
 * MAMR settings for SDRAM
 */

/* 8 column SDRAM */
#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_1X)
/* 9 column SDRAM */
#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_1X)

#endif	/* __CONFIG_H */