blob: 4d1cef3f98a3cdafc8540649afe7d1c6c6fa80a8 [file] [log] [blame]
/* Copyright (c) 2002 Intel Corporation */
#include <stdio.h>
#include "ethtool-util.h"
#define D102_REV_ID 12
#define MDI_MDIX_CONFIG_IS_OK 0x0010
#define MDI_MDIX_STATUS 0x0020
#define SOFT_INT 0x0200 /* Generate a S/W interrupt */
/* Interrupt masks */
#define ALL_INT_MASK 0x0100 /* Mask interrupts */
#define FCP_INT_MASK 0x0400 /* Flow Control Pause */
#define ER_INT_MASK 0x0800 /* Early Receive */
#define RNR_INT_MASK 0x1000 /* RU Not Ready */
#define CNA_INT_MASK 0x2000 /* CU Not Active */
#define FR_INT_MASK 0x4000 /* Frame Received */
#define CX_INT_MASK 0x8000 /* CU eXecution w/ I-bit done */
/* Interrupts pending */
#define FCP_INT_PENDING 0x0100 /* Flow Control Pause */
#define ER_INT_PENDING 0x0200 /* Early Receive */
#define SWI_INT_PENDING 0x0400 /* S/W generated interrupt */
#define MDI_INT_PENDING 0x0800 /* MDI read or write done */
#define RNR_INT_PENDING 0x1000 /* RU Became Not Ready */
#define CNA_INT_PENDING 0x2000 /* CU Became Inactive (IDLE) */
#define FR_INT_PENDING 0x4000 /* RU Received A Frame */
#define CX_INT_PENDING 0x8000 /* CU Completed Action Cmd */
/* Status */
#define CU_STATUS 0x00C0
#define RU_STATUS 0x003C
/* Commands */
#define CU_CMD 0x00F0
#define RU_CMD 0x0007
int
e100_dump_regs(struct ethtool_drvinfo *info, struct ethtool_regs *regs)
{
u32 *regs_buff = (u32 *)regs->data;
u8 version = (u8)(regs->version >> 24);
u8 rev_id = (u8)(regs->version);
u8 regs_len = regs->len / sizeof(u32);
u32 reg;
u16 scb_status, scb_cmd;
if(version != 1)
return -1;
reg = regs_buff[0];
scb_status = reg & 0x0000ffff;
scb_cmd = reg >> 16;
fprintf(stdout,
"SCB Status Word (Lower Word) 0x%04X\n",
scb_status);
switch ((scb_status & RU_STATUS) >> 2) {
case 0:
fprintf(stdout,
" RU Status: Idle\n");
break;
case 1:
fprintf(stdout,
" RU Status: Suspended\n");
break;
case 2:
fprintf(stdout,
" RU Status: No Resources\n");
break;
case 4:
fprintf(stdout,
" RU Status: Ready\n");
break;
case 9:
fprintf(stdout,
" RU Status: Suspended with no more RBDs\n");
break;
case 10:
fprintf(stdout,
" RU Status: No Resources due to no more RBDs\n");
break;
case 12:
fprintf(stdout,
" RU Status: Ready with no RBDs present\n");
break;
default:
fprintf(stdout,
" RU Status: Unknown State\n");
break;
}
switch ((scb_status & CU_STATUS) >> 6) {
case 0:
fprintf(stdout,
" CU Status: Idle\n");
break;
case 1:
fprintf(stdout,
" CU Status: Suspended\n");
break;
case 2:
fprintf(stdout,
" CU Status: Active\n");
break;
default:
fprintf(stdout,
" CU Status: Unknown State\n");
break;
}
fprintf(stdout,
" ---- Interrupts Pending ----\n"
" Flow Control Pause: %s\n"
" Early Receive: %s\n"
" Software Generated Interrupt: %s\n"
" MDI Done: %s\n"
" RU Not In Ready State: %s\n"
" CU Not in Active State: %s\n"
" RU Received Frame: %s\n"
" CU Completed Command: %s\n",
scb_status & FCP_INT_PENDING ? "yes" : "no",
scb_status & ER_INT_PENDING ? "yes" : "no",
scb_status & SWI_INT_PENDING ? "yes" : "no",
scb_status & MDI_INT_PENDING ? "yes" : "no",
scb_status & RNR_INT_PENDING ? "yes" : "no",
scb_status & CNA_INT_PENDING ? "yes" : "no",
scb_status & FR_INT_PENDING ? "yes" : "no",
scb_status & CX_INT_PENDING ? "yes" : "no");
fprintf(stdout,
"SCB Command Word (Upper Word) 0x%04X\n",
scb_cmd);
switch (scb_cmd & RU_CMD) {
case 0:
fprintf(stdout,
" RU Command: No Command\n");
break;
case 1:
fprintf(stdout,
" RU Command: RU Start\n");
break;
case 2:
fprintf(stdout,
" RU Command: RU Resume\n");
break;
case 4:
fprintf(stdout,
" RU Command: RU Abort\n");
break;
case 6:
fprintf(stdout,
" RU Command: Load RU Base\n");
break;
default:
fprintf(stdout,
" RU Command: Unknown\n");
break;
}
switch ((scb_cmd & CU_CMD) >> 4) {
case 0:
fprintf(stdout,
" CU Command: No Command\n");
break;
case 1:
fprintf(stdout,
" CU Command: CU Start\n");
break;
case 2:
fprintf(stdout,
" CU Command: CU Resume\n");
break;
case 4:
fprintf(stdout,
" CU Command: Load Dump Counters Address\n");
break;
case 5:
fprintf(stdout,
" CU Command: Dump Counters\n");
break;
case 6:
fprintf(stdout,
" CU Command: Load CU Base\n");
break;
case 7:
fprintf(stdout,
" CU Command: Dump & Reset Counters\n");
break;
default:
fprintf(stdout,
" CU Command: Unknown\n");
break;
}
fprintf(stdout,
" Software Generated Interrupt: %s\n",
scb_cmd & SOFT_INT ? "yes" : "no");
fprintf(stdout,
" ---- Interrupts Masked ----\n"
" ALL Interrupts: %s\n"
" Flow Control Pause: %s\n"
" Early Receive: %s\n"
" RU Not In Ready State: %s\n"
" CU Not in Active State: %s\n"
" RU Received Frame: %s\n"
" CU Completed Command: %s\n",
scb_cmd & ALL_INT_MASK ? "yes" : "no",
scb_cmd & FCP_INT_MASK ? "yes" : "no",
scb_cmd & ER_INT_MASK ? "yes" : "no",
scb_cmd & RNR_INT_MASK ? "yes" : "no",
scb_cmd & CNA_INT_MASK ? "yes" : "no",
scb_cmd & FR_INT_MASK ? "yes" : "no",
scb_cmd & CX_INT_MASK ? "yes" : "no");
if(regs_len > 1) {
fprintf(stdout, "MDI/MDI-X Status: ");
if(rev_id < D102_REV_ID)
fprintf(stdout, "MDI\n");
else {
u16 ctrl_reg = regs_buff[1];
if(ctrl_reg & MDI_MDIX_CONFIG_IS_OK) {
if(ctrl_reg & MDI_MDIX_STATUS)
fprintf(stdout, "MDI-X\n");
else
fprintf(stdout, "MDI\n");
} else
fprintf(stdout, "Unknown\n");
}
}
return 0;
}