.TH memtester "8" "July 2009" "memtester 4" "Maintenance Commands"
.SH NAME
memtester \- stress test to find memory subsystem faults.
.SH SYNOPSIS
.B memtester
[\f -p PHYSADDR\fR]
<\fIMEMORY\fR>
[\fIITERATIONS\fR]
.SH DESCRIPTION
.\" Add any additional description here
.PP
memtester is an effective userspace tester for stress-testing the memory
subsystem.  It is very effective at finding intermittent and non-deterministic
faults.  Note that problems in other hardware areas (overheating CPU, 
out-of-specification power supply, etc.) can cause intermittent memory faults,
so it is still up to you to determine where the fault lies through normal
hardware diagnostic procedures; memtester just helps you determine whether
a problem exists.
.PP
memtester will malloc(3) the amount of memory specified, if possible.  If
this fails, it will decrease the amount of memory requested until it succeeds.
It will then attempt to mlock(3) this memory; if it cannot do so, testing
will be slower and much less effective.  Run memtester as root so that it
can mlock the memory it tests.
.PP
Note that the maximum amount of memory that memtester can test will be less
than the total amount of memory installed in the system; the operating system,
libraries, and other system limits take some of the available memory.
memtester is also limited to the amount of memory available to a single
process; for example, on 32-bit machines with more than 4GB of memory,
memtester is still limited to less than 4GB.
.PP
Note that it is up to you to know how much memory you can safely allocate
for testing.  If you attempt to allocate more memory than is available,
memtester should figure that out, reduce the amount slightly, and try again.
However, this can lead to memtester successfully allocating and mlocking
essentially all free memory on the system -- if other programs are running,
this can lead to excessive swapping and slowing the system down to the point
that it is difficult to use.  If the system allows allocation of more memory
than is actually available (overcommit), it may lead to a deadlock, where
the system halts.  If the system has an out-of-memory process killer (like
Linux), memtester or another process may be killed by the OOM killer.
.PP
So choose wisely.
.PP
.SH OPTIONS
.TP
\f -p PHYSADDR\fR
tells memtester to test a specific region of memory starting at physical 
address PHYSADDR (given in hex), by mmap(2)ing /dev/mem.  This is mostly of
use to hardware developers, for testing memory-mapped I/O devices and similar.
Note that the memory region will be overwritten during testing, so it is not
safe to specify memory which is allocated for the system or for other
applications; doing so will cause them to crash.  If you absolutely must test
a particular region of actual physical memory, arrange to have that memory
allocated by your test software, and hold it in this allocated state, then
run memtester on it with this option.
.TP
\fIMEMORY\fR
the amount of memory to allocate and test, in megabytes by default.  You can
include a suffix of B, K, M, or G to indicate bytes, kilobytes, megabytes, or
gigabytes respectively.
.TP
\fIITERATIONS\fR
(optional) number of loops to iterate through.  Default is infinite.
.SH NOTE
.PP
memtester must be run with root privileges to mlock(3) its pages.  Testing
memory without locking the pages in place is mostly pointless and slow.
.SH EXIT CODE
.PP
memtester's exit code is 0 when everything works properly.  Otherwise,
it is the logical OR of the following values:
.TP
\f0x01
error allocating or locking memory, or invocation error
.TP
\f0x02
error during stuck address test
.TP
\f0x04
error during one of the other tests
.SH AUTHOR
Written by Charles Cazabon.
.SH "REPORTING BUGS"
Report bugs to <charlesc-memtester-bugs@pyropus.ca>.
.PP
.SH COPYRIGHT
Copyright \(co 2009 Charles Cazabon
.br
This is free software; see the file COPYING for copying conditions.  There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.