| /* | |
| * vme8349.c -- esd VME8349 board support | |
| * | |
| * Copyright (c) 2008-2009 esd gmbh. | |
| * | |
| * (C) Copyright 2006 | |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
| * | |
| * Reinhard Arlt <reinhard.arlt@esd-electronics.com> | |
| * Based on board/mpc8349emds/mpc8349emds.c (and previous 834x releases.) | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #include <common.h> | |
| #include <ioports.h> | |
| #include <mpc83xx.h> | |
| #include <asm/mpc8349_pci.h> | |
| #if defined(CONFIG_OF_LIBFDT) | |
| #include <libfdt.h> | |
| #endif | |
| #include <asm/io.h> | |
| #include <asm/mmu.h> | |
| #include <spd.h> | |
| #include <spd_sdram.h> | |
| #include <i2c.h> | |
| #include <netdev.h> | |
| void ddr_enable_ecc(unsigned int dram_size); | |
| phys_size_t initdram(int board_type) | |
| { | |
| volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR; | |
| u32 msize = 0; | |
| if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im) | |
| return -1; | |
| /* DDR SDRAM - Main memory */ | |
| im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR; | |
| msize = spd_sdram(); | |
| #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) | |
| /* | |
| * Initialize and enable DDR ECC. | |
| */ | |
| ddr_enable_ecc(msize * 1024 * 1024); | |
| #endif | |
| /* Now check memory size (after ECC is initialized) */ | |
| msize = get_ram_size(0, msize); | |
| /* return total bus SDRAM size(bytes) -- DDR */ | |
| return msize * 1024 * 1024; | |
| } | |
| int checkboard(void) | |
| { | |
| #ifdef VME_CADDY2 | |
| puts("Board: esd VME-CADDY/2\n"); | |
| #else | |
| puts("Board: esd VME-CPU/8349\n"); | |
| #endif | |
| return 0; | |
| } | |
| #ifdef VME_CADDY2 | |
| int board_eth_init(bd_t *bis) | |
| { | |
| return pci_eth_init(bis); | |
| } | |
| #endif | |
| #if defined(CONFIG_OF_BOARD_SETUP) | |
| void ft_board_setup(void *blob, bd_t *bd) | |
| { | |
| ft_cpu_setup(blob, bd); | |
| #ifdef CONFIG_PCI | |
| ft_pci_setup(blob, bd); | |
| #endif | |
| } | |
| #endif | |
| int misc_init_r() | |
| { | |
| immap_t *im = (immap_t *)CONFIG_SYS_IMMR; | |
| clrsetbits_be32(&im->im_lbc.lcrr, LBCR_LDIS, 0); | |
| return 0; | |
| } | |
| /* | |
| * Provide SPD values for spd_sdram(). Both boards (VME-CADDY/2 | |
| * and VME-CADDY/2) have different SDRAM configurations. | |
| */ | |
| #ifdef VME_CADDY2 | |
| #define SMALL_RAM 0xff | |
| #define LARGE_RAM 0x00 | |
| #else | |
| #define SMALL_RAM 0x00 | |
| #define LARGE_RAM 0xff | |
| #endif | |
| #define SPD_VAL(a, b) (((a) & SMALL_RAM) | ((b) & LARGE_RAM)) | |
| static spd_eeprom_t default_spd_eeprom = { | |
| SPD_VAL(0x80, 0x80), /* 00 use 128 Bytes */ | |
| SPD_VAL(0x07, 0x07), /* 01 use 128 Bytes */ | |
| SPD_MEMTYPE_DDR2, /* 02 type is DDR2 */ | |
| SPD_VAL(0x0d, 0x0d), /* 03 rows: 13 */ | |
| SPD_VAL(0x09, 0x0a), /* 04 cols: 9 / 10 */ | |
| SPD_VAL(0x00, 0x00), /* 05 */ | |
| SPD_VAL(0x40, 0x40), /* 06 */ | |
| SPD_VAL(0x00, 0x00), /* 07 */ | |
| SPD_VAL(0x05, 0x05), /* 08 */ | |
| SPD_VAL(0x30, 0x30), /* 09 */ | |
| SPD_VAL(0x45, 0x45), /* 10 */ | |
| SPD_VAL(0x02, 0x02), /* 11 ecc used */ | |
| SPD_VAL(0x82, 0x82), /* 12 */ | |
| SPD_VAL(0x10, 0x10), /* 13 */ | |
| SPD_VAL(0x08, 0x08), /* 14 */ | |
| SPD_VAL(0x00, 0x00), /* 15 */ | |
| SPD_VAL(0x0c, 0x0c), /* 16 */ | |
| SPD_VAL(0x04, 0x08), /* 17 banks: 4 / 8 */ | |
| SPD_VAL(0x38, 0x38), /* 18 */ | |
| SPD_VAL(0x00, 0x00), /* 19 */ | |
| SPD_VAL(0x02, 0x02), /* 20 */ | |
| SPD_VAL(0x00, 0x00), /* 21 */ | |
| SPD_VAL(0x03, 0x03), /* 22 */ | |
| SPD_VAL(0x3d, 0x3d), /* 23 */ | |
| SPD_VAL(0x45, 0x45), /* 24 */ | |
| SPD_VAL(0x50, 0x50), /* 25 */ | |
| SPD_VAL(0x45, 0x45), /* 26 */ | |
| SPD_VAL(0x3c, 0x3c), /* 27 */ | |
| SPD_VAL(0x28, 0x28), /* 28 */ | |
| SPD_VAL(0x3c, 0x3c), /* 29 */ | |
| SPD_VAL(0x2d, 0x2d), /* 30 */ | |
| SPD_VAL(0x20, 0x80), /* 31 */ | |
| SPD_VAL(0x20, 0x20), /* 32 */ | |
| SPD_VAL(0x27, 0x27), /* 33 */ | |
| SPD_VAL(0x10, 0x10), /* 34 */ | |
| SPD_VAL(0x17, 0x17), /* 35 */ | |
| SPD_VAL(0x3c, 0x3c), /* 36 */ | |
| SPD_VAL(0x1e, 0x1e), /* 37 */ | |
| SPD_VAL(0x1e, 0x1e), /* 38 */ | |
| SPD_VAL(0x00, 0x00), /* 39 */ | |
| SPD_VAL(0x00, 0x06), /* 40 */ | |
| SPD_VAL(0x37, 0x37), /* 41 */ | |
| SPD_VAL(0x4b, 0x7f), /* 42 */ | |
| SPD_VAL(0x80, 0x80), /* 43 */ | |
| SPD_VAL(0x18, 0x18), /* 44 */ | |
| SPD_VAL(0x22, 0x22), /* 45 */ | |
| SPD_VAL(0x00, 0x00), /* 46 */ | |
| { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, | |
| SPD_VAL(0x10, 0x10), /* 62 */ | |
| SPD_VAL(0x7e, 0x1d), /* 63 */ | |
| { 'e', 's', 'd', '-', 'g', 'm', 'b', 'h' }, | |
| SPD_VAL(0x00, 0x00), /* 72 */ | |
| #ifdef VME_CADDY2 | |
| { "vme-caddy/2 ram " } | |
| #else | |
| { "vme-cpu/2 ram " } | |
| #endif | |
| }; | |
| int vme8349_read_spd(uchar chip, uint addr, int alen, uchar *buffer, int len) | |
| { | |
| int old_bus = i2c_get_bus_num(); | |
| unsigned int l, sum; | |
| int valid = 0; | |
| i2c_set_bus_num(0); | |
| if (i2c_read(chip, addr, alen, buffer, len) == 0) | |
| if (memcmp(&buffer[64], &default_spd_eeprom.mid[0], 8) == 0) { | |
| sum = 0; | |
| for (l = 0; l < 63; l++) | |
| sum = (sum + buffer[l]) & 0xff; | |
| if (sum == buffer[63]) | |
| valid = 1; | |
| else | |
| printf("Invalid checksum in EEPROM %02x %02x\n", | |
| sum, buffer[63]); | |
| } | |
| if (valid == 0) { | |
| memcpy(buffer, (void *)&default_spd_eeprom, len); | |
| sum = 0; | |
| for (l = 0; l < 63; l++) | |
| sum = (sum + buffer[l]) & 0xff; | |
| if (sum != buffer[63]) | |
| printf("Invalid checksum in FLASH %02x %02x\n", | |
| sum, buffer[63]); | |
| buffer[63] = sum; | |
| } | |
| i2c_set_bus_num(old_bus); | |
| return 0; | |
| } |