/*******************************************************************************

  Intel 10 Gigabit PCI Express Linux driver
  Copyright(c) 1999 - 2010 Intel Corporation.

  This program is free software; you can redistribute it and/or modify it
  under the terms and conditions of the GNU General Public License,
  version 2, as published by the Free Software Foundation.

  This program is distributed in the hope it will be useful, but WITHOUT
  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  more details.

  You should have received a copy of the GNU General Public License along with
  this program; if not, write to the Free Software Foundation, Inc.,
  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.

  The full GNU General Public License is included in this distribution in
  the file called "COPYING".

  Contact Information:
  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497

*******************************************************************************/

#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/sched.h>

#include "ixgbe.h"
#include "ixgbe_phy.h"
#include "ixgbe_mbx.h"

#define IXGBE_82599_MAX_TX_QUEUES 128
#define IXGBE_82599_MAX_RX_QUEUES 128
#define IXGBE_82599_RAR_ENTRIES   128
#define IXGBE_82599_MC_TBL_SIZE   128
#define IXGBE_82599_VFT_TBL_SIZE  128

static void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw);
static void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw);
static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw);
static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
						 ixgbe_link_speed speed,
						 bool autoneg,
						 bool autoneg_wait_to_complete);
static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
                                           ixgbe_link_speed speed,
                                           bool autoneg,
                                           bool autoneg_wait_to_complete);
static s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw,
				      bool autoneg_wait_to_complete);
static s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
                               ixgbe_link_speed speed,
                               bool autoneg,
                               bool autoneg_wait_to_complete);
static s32 ixgbe_get_copper_link_capabilities_82599(struct ixgbe_hw *hw,
                                             ixgbe_link_speed *speed,
                                             bool *autoneg);
static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw,
                                         ixgbe_link_speed speed,
                                         bool autoneg,
                                         bool autoneg_wait_to_complete);
static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw);

static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw)
{
	struct ixgbe_mac_info *mac = &hw->mac;
	if (hw->phy.multispeed_fiber) {
		/* Set up dual speed SFP+ support */
		mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber;
		mac->ops.disable_tx_laser =
		                       &ixgbe_disable_tx_laser_multispeed_fiber;
		mac->ops.enable_tx_laser =
		                        &ixgbe_enable_tx_laser_multispeed_fiber;
		mac->ops.flap_tx_laser = &ixgbe_flap_tx_laser_multispeed_fiber;
	} else {
		mac->ops.disable_tx_laser = NULL;
		mac->ops.enable_tx_laser = NULL;
		mac->ops.flap_tx_laser = NULL;
		if ((mac->ops.get_media_type(hw) ==
		     ixgbe_media_type_backplane) &&
		    (hw->phy.smart_speed == ixgbe_smart_speed_auto ||
		     hw->phy.smart_speed == ixgbe_smart_speed_on))
			mac->ops.setup_link = &ixgbe_setup_mac_link_smartspeed;
		else
			mac->ops.setup_link = &ixgbe_setup_mac_link_82599;
	}
}

static s32 ixgbe_setup_sfp_modules_82599(struct ixgbe_hw *hw)
{
	s32 ret_val = 0;
	u16 list_offset, data_offset, data_value;

	if (hw->phy.sfp_type != ixgbe_sfp_type_unknown) {
		ixgbe_init_mac_link_ops_82599(hw);

		hw->phy.ops.reset = NULL;

		ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset,
		                                              &data_offset);

		if (ret_val != 0)
			goto setup_sfp_out;

		/* PHY config will finish before releasing the semaphore */
		ret_val = ixgbe_acquire_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
		if (ret_val != 0) {
			ret_val = IXGBE_ERR_SWFW_SYNC;
			goto setup_sfp_out;
		}

		hw->eeprom.ops.read(hw, ++data_offset, &data_value);
		while (data_value != 0xffff) {
			IXGBE_WRITE_REG(hw, IXGBE_CORECTL, data_value);
			IXGBE_WRITE_FLUSH(hw);
			hw->eeprom.ops.read(hw, ++data_offset, &data_value);
		}
		/* Now restart DSP by setting Restart_AN */
		IXGBE_WRITE_REG(hw, IXGBE_AUTOC,
		    (IXGBE_READ_REG(hw, IXGBE_AUTOC) | IXGBE_AUTOC_AN_RESTART));

		/* Release the semaphore */
		ixgbe_release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
		/* Delay obtaining semaphore again to allow FW access */
		msleep(hw->eeprom.semaphore_delay);
	}

setup_sfp_out:
	return ret_val;
}

static s32 ixgbe_get_invariants_82599(struct ixgbe_hw *hw)
{
	struct ixgbe_mac_info *mac = &hw->mac;

	ixgbe_init_mac_link_ops_82599(hw);

	mac->mcft_size = IXGBE_82599_MC_TBL_SIZE;
	mac->vft_size = IXGBE_82599_VFT_TBL_SIZE;
	mac->num_rar_entries = IXGBE_82599_RAR_ENTRIES;
	mac->max_rx_queues = IXGBE_82599_MAX_RX_QUEUES;
	mac->max_tx_queues = IXGBE_82599_MAX_TX_QUEUES;
	mac->max_msix_vectors = ixgbe_get_pcie_msix_count_generic(hw);

	return 0;
}

/**
 *  ixgbe_init_phy_ops_82599 - PHY/SFP specific init
 *  @hw: pointer to hardware structure
 *
 *  Initialize any function pointers that were not able to be
 *  set during get_invariants because the PHY/SFP type was
 *  not known.  Perform the SFP init if necessary.
 *
 **/
static s32 ixgbe_init_phy_ops_82599(struct ixgbe_hw *hw)
{
	struct ixgbe_mac_info *mac = &hw->mac;
	struct ixgbe_phy_info *phy = &hw->phy;
	s32 ret_val = 0;

	/* Identify the PHY or SFP module */
	ret_val = phy->ops.identify(hw);

	/* Setup function pointers based on detected SFP module and speeds */
	ixgbe_init_mac_link_ops_82599(hw);

	/* If copper media, overwrite with copper function pointers */
	if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) {
		mac->ops.setup_link = &ixgbe_setup_copper_link_82599;
		mac->ops.get_link_capabilities =
		                  &ixgbe_get_copper_link_capabilities_82599;
	}

	/* Set necessary function pointers based on phy type */
	switch (hw->phy.type) {
	case ixgbe_phy_tn:
		phy->ops.check_link = &ixgbe_check_phy_link_tnx;
		phy->ops.get_firmware_version =
		             &ixgbe_get_phy_firmware_version_tnx;
		break;
	default:
		break;
	}

	return ret_val;
}

/**
 *  ixgbe_get_link_capabilities_82599 - Determines link capabilities
 *  @hw: pointer to hardware structure
 *  @speed: pointer to link speed
 *  @negotiation: true when autoneg or autotry is enabled
 *
 *  Determines the link capabilities by reading the AUTOC register.
 **/
static s32 ixgbe_get_link_capabilities_82599(struct ixgbe_hw *hw,
                                             ixgbe_link_speed *speed,
                                             bool *negotiation)
{
	s32 status = 0;
	u32 autoc = 0;

	/* Determine 1G link capabilities off of SFP+ type */
	if (hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 ||
	    hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1) {
		*speed = IXGBE_LINK_SPEED_1GB_FULL;
		*negotiation = true;
		goto out;
	}

	/*
	 * Determine link capabilities based on the stored value of AUTOC,
	 * which represents EEPROM defaults.  If AUTOC value has not been
	 * stored, use the current register value.
	 */
	if (hw->mac.orig_link_settings_stored)
		autoc = hw->mac.orig_autoc;
	else
		autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);

	switch (autoc & IXGBE_AUTOC_LMS_MASK) {
	case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
		*speed = IXGBE_LINK_SPEED_1GB_FULL;
		*negotiation = false;
		break;

	case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
		*speed = IXGBE_LINK_SPEED_10GB_FULL;
		*negotiation = false;
		break;

	case IXGBE_AUTOC_LMS_1G_AN:
		*speed = IXGBE_LINK_SPEED_1GB_FULL;
		*negotiation = true;
		break;

	case IXGBE_AUTOC_LMS_10G_SERIAL:
		*speed = IXGBE_LINK_SPEED_10GB_FULL;
		*negotiation = false;
		break;

	case IXGBE_AUTOC_LMS_KX4_KX_KR:
	case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN:
		*speed = IXGBE_LINK_SPEED_UNKNOWN;
		if (autoc & IXGBE_AUTOC_KR_SUPP)
			*speed |= IXGBE_LINK_SPEED_10GB_FULL;
		if (autoc & IXGBE_AUTOC_KX4_SUPP)
			*speed |= IXGBE_LINK_SPEED_10GB_FULL;
		if (autoc & IXGBE_AUTOC_KX_SUPP)
			*speed |= IXGBE_LINK_SPEED_1GB_FULL;
		*negotiation = true;
		break;

	case IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII:
		*speed = IXGBE_LINK_SPEED_100_FULL;
		if (autoc & IXGBE_AUTOC_KR_SUPP)
			*speed |= IXGBE_LINK_SPEED_10GB_FULL;
		if (autoc & IXGBE_AUTOC_KX4_SUPP)
			*speed |= IXGBE_LINK_SPEED_10GB_FULL;
		if (autoc & IXGBE_AUTOC_KX_SUPP)
			*speed |= IXGBE_LINK_SPEED_1GB_FULL;
		*negotiation = true;
		break;

	case IXGBE_AUTOC_LMS_SGMII_1G_100M:
		*speed = IXGBE_LINK_SPEED_1GB_FULL | IXGBE_LINK_SPEED_100_FULL;
		*negotiation = false;
		break;

	default:
		status = IXGBE_ERR_LINK_SETUP;
		goto out;
		break;
	}

	if (hw->phy.multispeed_fiber) {
		*speed |= IXGBE_LINK_SPEED_10GB_FULL |
		          IXGBE_LINK_SPEED_1GB_FULL;
		*negotiation = true;
	}

out:
	return status;
}

/**
 *  ixgbe_get_copper_link_capabilities_82599 - Determines link capabilities
 *  @hw: pointer to hardware structure
 *  @speed: pointer to link speed
 *  @autoneg: boolean auto-negotiation value
 *
 *  Determines the link capabilities by reading the AUTOC register.
 **/
static s32 ixgbe_get_copper_link_capabilities_82599(struct ixgbe_hw *hw,
                                                    ixgbe_link_speed *speed,
                                                    bool *autoneg)
{
	s32 status = IXGBE_ERR_LINK_SETUP;
	u16 speed_ability;

	*speed = 0;
	*autoneg = true;

	status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD,
	                              &speed_ability);

	if (status == 0) {
		if (speed_ability & MDIO_SPEED_10G)
		    *speed |= IXGBE_LINK_SPEED_10GB_FULL;
		if (speed_ability & MDIO_PMA_SPEED_1000)
		    *speed |= IXGBE_LINK_SPEED_1GB_FULL;
	}

	return status;
}

/**
 *  ixgbe_get_media_type_82599 - Get media type
 *  @hw: pointer to hardware structure
 *
 *  Returns the media type (fiber, copper, backplane)
 **/
static enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw)
{
	enum ixgbe_media_type media_type;

	/* Detect if there is a copper PHY attached. */
	if (hw->phy.type == ixgbe_phy_cu_unknown ||
	    hw->phy.type == ixgbe_phy_tn) {
		media_type = ixgbe_media_type_copper;
		goto out;
	}

	switch (hw->device_id) {
	case IXGBE_DEV_ID_82599_KX4:
	case IXGBE_DEV_ID_82599_KX4_MEZZ:
	case IXGBE_DEV_ID_82599_COMBO_BACKPLANE:
	case IXGBE_DEV_ID_82599_KR:
	case IXGBE_DEV_ID_82599_XAUI_LOM:
		/* Default device ID is mezzanine card KX/KX4 */
		media_type = ixgbe_media_type_backplane;
		break;
	case IXGBE_DEV_ID_82599_SFP:
	case IXGBE_DEV_ID_82599_SFP_EM:
		media_type = ixgbe_media_type_fiber;
		break;
	case IXGBE_DEV_ID_82599_CX4:
		media_type = ixgbe_media_type_cx4;
		break;
	default:
		media_type = ixgbe_media_type_unknown;
		break;
	}
out:
	return media_type;
}

/**
 *  ixgbe_start_mac_link_82599 - Setup MAC link settings
 *  @hw: pointer to hardware structure
 *  @autoneg_wait_to_complete: true when waiting for completion is needed
 *
 *  Configures link settings based on values in the ixgbe_hw struct.
 *  Restarts the link.  Performs autonegotiation if needed.
 **/
static s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw,
                               bool autoneg_wait_to_complete)
{
	u32 autoc_reg;
	u32 links_reg;
	u32 i;
	s32 status = 0;

	/* Restart link */
	autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
	autoc_reg |= IXGBE_AUTOC_AN_RESTART;
	IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);

	/* Only poll for autoneg to complete if specified to do so */
	if (autoneg_wait_to_complete) {
		if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
		     IXGBE_AUTOC_LMS_KX4_KX_KR ||
		    (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
		     IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
		    (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
		     IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
			links_reg = 0; /* Just in case Autoneg time = 0 */
			for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
				links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
				if (links_reg & IXGBE_LINKS_KX_AN_COMP)
					break;
				msleep(100);
			}
			if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
				status = IXGBE_ERR_AUTONEG_NOT_COMPLETE;
				hw_dbg(hw, "Autoneg did not complete.\n");
			}
		}
	}

	/* Add delay to filter out noises during initial link setup */
	msleep(50);

	return status;
}

 /**
  *  ixgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser
  *  @hw: pointer to hardware structure
  *
  *  The base drivers may require better control over SFP+ module
  *  PHY states.  This includes selectively shutting down the Tx
  *  laser on the PHY, effectively halting physical link.
  **/
static void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
{
	u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);

	/* Disable tx laser; allow 100us to go dark per spec */
	esdp_reg |= IXGBE_ESDP_SDP3;
	IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
	IXGBE_WRITE_FLUSH(hw);
	udelay(100);
}

/**
 *  ixgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser
 *  @hw: pointer to hardware structure
 *
 *  The base drivers may require better control over SFP+ module
 *  PHY states.  This includes selectively turning on the Tx
 *  laser on the PHY, effectively starting physical link.
 **/
static void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
{
	u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);

	/* Enable tx laser; allow 100ms to light up */
	esdp_reg &= ~IXGBE_ESDP_SDP3;
	IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
	IXGBE_WRITE_FLUSH(hw);
	msleep(100);
}

/**
 *  ixgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser
 *  @hw: pointer to hardware structure
 *
 *  When the driver changes the link speeds that it can support,
 *  it sets autotry_restart to true to indicate that we need to
 *  initiate a new autotry session with the link partner.  To do
 *  so, we set the speed then disable and re-enable the tx laser, to
 *  alert the link partner that it also needs to restart autotry on its
 *  end.  This is consistent with true clause 37 autoneg, which also
 *  involves a loss of signal.
 **/
static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
{
	hw_dbg(hw, "ixgbe_flap_tx_laser_multispeed_fiber\n");

	if (hw->mac.autotry_restart) {
		ixgbe_disable_tx_laser_multispeed_fiber(hw);
		ixgbe_enable_tx_laser_multispeed_fiber(hw);
		hw->mac.autotry_restart = false;
	}
}

/**
 *  ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
 *  @hw: pointer to hardware structure
 *  @speed: new link speed
 *  @autoneg: true if autonegotiation enabled
 *  @autoneg_wait_to_complete: true when waiting for completion is needed
 *
 *  Set the link speed in the AUTOC register and restarts link.
 **/
s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
                                          ixgbe_link_speed speed,
                                          bool autoneg,
                                          bool autoneg_wait_to_complete)
{
	s32 status = 0;
	ixgbe_link_speed phy_link_speed;
	ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
	u32 speedcnt = 0;
	u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
	bool link_up = false;
	bool negotiation;
	int i;

	/* Mask off requested but non-supported speeds */
	hw->mac.ops.get_link_capabilities(hw, &phy_link_speed, &negotiation);
	speed &= phy_link_speed;

	/*
	 * Try each speed one by one, highest priority first.  We do this in
	 * software because 10gb fiber doesn't support speed autonegotiation.
	 */
	if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
		speedcnt++;
		highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;

		/* If we already have link at this speed, just jump out */
		hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);

		if ((phy_link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
			goto out;

		/* Set the module link speed */
		esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
		IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
		IXGBE_WRITE_FLUSH(hw);

		/* Allow module to change analog characteristics (1G->10G) */
		msleep(40);

		status = ixgbe_setup_mac_link_82599(hw,
		                               IXGBE_LINK_SPEED_10GB_FULL,
		                               autoneg,
		                               autoneg_wait_to_complete);
		if (status != 0)
			return status;

		/* Flap the tx laser if it has not already been done */
		hw->mac.ops.flap_tx_laser(hw);

		/*
		 * Wait for the controller to acquire link.  Per IEEE 802.3ap,
		 * Section 73.10.2, we may have to wait up to 500ms if KR is
		 * attempted.  82599 uses the same timing for 10g SFI.
		 */

		for (i = 0; i < 5; i++) {
			/* Wait for the link partner to also set speed */
			msleep(100);

			/* If we have link, just jump out */
			hw->mac.ops.check_link(hw, &phy_link_speed,
			                       &link_up, false);
			if (link_up)
				goto out;
		}
	}

	if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
		speedcnt++;
		if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
			highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;

		/* If we already have link at this speed, just jump out */
		hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);

		if ((phy_link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
			goto out;

		/* Set the module link speed */
		esdp_reg &= ~IXGBE_ESDP_SDP5;
		esdp_reg |= IXGBE_ESDP_SDP5_DIR;
		IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
		IXGBE_WRITE_FLUSH(hw);

		/* Allow module to change analog characteristics (10G->1G) */
		msleep(40);

		status = ixgbe_setup_mac_link_82599(hw,
		                                      IXGBE_LINK_SPEED_1GB_FULL,
		                                      autoneg,
		                                      autoneg_wait_to_complete);
		if (status != 0)
			return status;

		/* Flap the tx laser if it has not already been done */
		hw->mac.ops.flap_tx_laser(hw);

		/* Wait for the link partner to also set speed */
		msleep(100);

		/* If we have link, just jump out */
		hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
		if (link_up)
			goto out;
	}

	/*
	 * We didn't get link.  Configure back to the highest speed we tried,
	 * (if there was more than one).  We call ourselves back with just the
	 * single highest speed that the user requested.
	 */
	if (speedcnt > 1)
		status = ixgbe_setup_mac_link_multispeed_fiber(hw,
		                                               highest_link_speed,
		                                               autoneg,
		                                               autoneg_wait_to_complete);

out:
	/* Set autoneg_advertised value based on input link speed */
	hw->phy.autoneg_advertised = 0;

	if (speed & IXGBE_LINK_SPEED_10GB_FULL)
		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;

	if (speed & IXGBE_LINK_SPEED_1GB_FULL)
		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;

	return status;
}

/**
 *  ixgbe_setup_mac_link_smartspeed - Set MAC link speed using SmartSpeed
 *  @hw: pointer to hardware structure
 *  @speed: new link speed
 *  @autoneg: true if autonegotiation enabled
 *  @autoneg_wait_to_complete: true when waiting for completion is needed
 *
 *  Implements the Intel SmartSpeed algorithm.
 **/
static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
				     ixgbe_link_speed speed, bool autoneg,
				     bool autoneg_wait_to_complete)
{
	s32 status = 0;
	ixgbe_link_speed link_speed;
	s32 i, j;
	bool link_up = false;
	u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
	struct ixgbe_adapter *adapter = hw->back;

	hw_dbg(hw, "ixgbe_setup_mac_link_smartspeed.\n");

	 /* Set autoneg_advertised value based on input link speed */
	hw->phy.autoneg_advertised = 0;

	if (speed & IXGBE_LINK_SPEED_10GB_FULL)
		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;

	if (speed & IXGBE_LINK_SPEED_1GB_FULL)
		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;

	if (speed & IXGBE_LINK_SPEED_100_FULL)
		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL;

	/*
	 * Implement Intel SmartSpeed algorithm.  SmartSpeed will reduce the
	 * autoneg advertisement if link is unable to be established at the
	 * highest negotiated rate.  This can sometimes happen due to integrity
	 * issues with the physical media connection.
	 */

	/* First, try to get link with full advertisement */
	hw->phy.smart_speed_active = false;
	for (j = 0; j < IXGBE_SMARTSPEED_MAX_RETRIES; j++) {
		status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
						    autoneg_wait_to_complete);
		if (status)
			goto out;

		/*
		 * Wait for the controller to acquire link.  Per IEEE 802.3ap,
		 * Section 73.10.2, we may have to wait up to 500ms if KR is
		 * attempted, or 200ms if KX/KX4/BX/BX4 is attempted, per
		 * Table 9 in the AN MAS.
		 */
		for (i = 0; i < 5; i++) {
			mdelay(100);

			/* If we have link, just jump out */
			hw->mac.ops.check_link(hw, &link_speed,
			                       &link_up, false);
			if (link_up)
				goto out;
		}
	}

	/*
	 * We didn't get link.  If we advertised KR plus one of KX4/KX
	 * (or BX4/BX), then disable KR and try again.
	 */
	if (((autoc_reg & IXGBE_AUTOC_KR_SUPP) == 0) ||
	    ((autoc_reg & IXGBE_AUTOC_KX4_KX_SUPP_MASK) == 0))
		goto out;

	/* Turn SmartSpeed on to disable KR support */
	hw->phy.smart_speed_active = true;
	status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
					    autoneg_wait_to_complete);
	if (status)
		goto out;

	/*
	 * Wait for the controller to acquire link.  600ms will allow for
	 * the AN link_fail_inhibit_timer as well for multiple cycles of
	 * parallel detect, both 10g and 1g. This allows for the maximum
	 * connect attempts as defined in the AN MAS table 73-7.
	 */
	for (i = 0; i < 6; i++) {
		mdelay(100);

		/* If we have link, just jump out */
		hw->mac.ops.check_link(hw, &link_speed,
		                       &link_up, false);
		if (link_up)
			goto out;
	}

	/* We didn't get link.  Turn SmartSpeed back off. */
	hw->phy.smart_speed_active = false;
	status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
					    autoneg_wait_to_complete);

out:
	if (link_up && (link_speed == IXGBE_LINK_SPEED_1GB_FULL))
		e_info(hw, "Smartspeed has downgraded the link speed from "
		       "the maximum advertised\n");
	return status;
}

/**
 *  ixgbe_setup_mac_link_82599 - Set MAC link speed
 *  @hw: pointer to hardware structure
 *  @speed: new link speed
 *  @autoneg: true if autonegotiation enabled
 *  @autoneg_wait_to_complete: true when waiting for completion is needed
 *
 *  Set the link speed in the AUTOC register and restarts link.
 **/
static s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
                               ixgbe_link_speed speed, bool autoneg,
                               bool autoneg_wait_to_complete)
{
	s32 status = 0;
	u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
	u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
	u32 start_autoc = autoc;
	u32 orig_autoc = 0;
	u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK;
	u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
	u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK;
	u32 links_reg;
	u32 i;
	ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN;

	/* Check to see if speed passed in is supported. */
	hw->mac.ops.get_link_capabilities(hw, &link_capabilities, &autoneg);
	speed &= link_capabilities;

	if (speed == IXGBE_LINK_SPEED_UNKNOWN) {
		status = IXGBE_ERR_LINK_SETUP;
		goto out;
	}

	/* Use stored value (EEPROM defaults) of AUTOC to find KR/KX4 support*/
	if (hw->mac.orig_link_settings_stored)
		orig_autoc = hw->mac.orig_autoc;
	else
		orig_autoc = autoc;


	if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
	    link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
	    link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
		/* Set KX4/KX/KR support according to speed requested */
		autoc &= ~(IXGBE_AUTOC_KX4_KX_SUPP_MASK | IXGBE_AUTOC_KR_SUPP);
		if (speed & IXGBE_LINK_SPEED_10GB_FULL)
			if (orig_autoc & IXGBE_AUTOC_KX4_SUPP)
				autoc |= IXGBE_AUTOC_KX4_SUPP;
			if ((orig_autoc & IXGBE_AUTOC_KR_SUPP) &&
			    (hw->phy.smart_speed_active == false))
				autoc |= IXGBE_AUTOC_KR_SUPP;
		if (speed & IXGBE_LINK_SPEED_1GB_FULL)
			autoc |= IXGBE_AUTOC_KX_SUPP;
	} else if ((pma_pmd_1g == IXGBE_AUTOC_1G_SFI) &&
	           (link_mode == IXGBE_AUTOC_LMS_1G_LINK_NO_AN ||
	            link_mode == IXGBE_AUTOC_LMS_1G_AN)) {
		/* Switch from 1G SFI to 10G SFI if requested */
		if ((speed == IXGBE_LINK_SPEED_10GB_FULL) &&
		    (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)) {
			autoc &= ~IXGBE_AUTOC_LMS_MASK;
			autoc |= IXGBE_AUTOC_LMS_10G_SERIAL;
		}
	} else if ((pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI) &&
	           (link_mode == IXGBE_AUTOC_LMS_10G_SERIAL)) {
		/* Switch from 10G SFI to 1G SFI if requested */
		if ((speed == IXGBE_LINK_SPEED_1GB_FULL) &&
		    (pma_pmd_1g == IXGBE_AUTOC_1G_SFI)) {
			autoc &= ~IXGBE_AUTOC_LMS_MASK;
			if (autoneg)
				autoc |= IXGBE_AUTOC_LMS_1G_AN;
			else
				autoc |= IXGBE_AUTOC_LMS_1G_LINK_NO_AN;
		}
	}

	if (autoc != start_autoc) {
		/* Restart link */
		autoc |= IXGBE_AUTOC_AN_RESTART;
		IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);

		/* Only poll for autoneg to complete if specified to do so */
		if (autoneg_wait_to_complete) {
			if (link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR ||
			    link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN ||
			    link_mode == IXGBE_AUTOC_LMS_KX4_KX_KR_SGMII) {
				links_reg = 0; /*Just in case Autoneg time=0*/
				for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
					links_reg =
					       IXGBE_READ_REG(hw, IXGBE_LINKS);
					if (links_reg & IXGBE_LINKS_KX_AN_COMP)
						break;
					msleep(100);
				}
				if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
					status =
					        IXGBE_ERR_AUTONEG_NOT_COMPLETE;
					hw_dbg(hw, "Autoneg did not "
					       "complete.\n");
				}
			}
		}

		/* Add delay to filter out noises during initial link setup */
		msleep(50);
	}

out:
	return status;
}

/**
 *  ixgbe_setup_copper_link_82599 - Set the PHY autoneg advertised field
 *  @hw: pointer to hardware structure
 *  @speed: new link speed
 *  @autoneg: true if autonegotiation enabled
 *  @autoneg_wait_to_complete: true if waiting is needed to complete
 *
 *  Restarts link on PHY and MAC based on settings passed in.
 **/
static s32 ixgbe_setup_copper_link_82599(struct ixgbe_hw *hw,
                                         ixgbe_link_speed speed,
                                         bool autoneg,
                                         bool autoneg_wait_to_complete)
{
	s32 status;

	/* Setup the PHY according to input speed */
	status = hw->phy.ops.setup_link_speed(hw, speed, autoneg,
	                                      autoneg_wait_to_complete);
	/* Set up MAC */
	ixgbe_start_mac_link_82599(hw, autoneg_wait_to_complete);

	return status;
}

/**
 *  ixgbe_reset_hw_82599 - Perform hardware reset
 *  @hw: pointer to hardware structure
 *
 *  Resets the hardware by resetting the transmit and receive units, masks
 *  and clears all interrupts, perform a PHY reset, and perform a link (MAC)
 *  reset.
 **/
static s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
{
	s32 status = 0;
	u32 ctrl;
	u32 i;
	u32 autoc;
	u32 autoc2;

	/* Call adapter stop to disable tx/rx and clear interrupts */
	hw->mac.ops.stop_adapter(hw);

	/* PHY ops must be identified and initialized prior to reset */

	/* Init PHY and function pointers, perform SFP setup */
	status = hw->phy.ops.init(hw);

	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
		goto reset_hw_out;

	/* Setup SFP module if there is one present. */
	if (hw->phy.sfp_setup_needed) {
		status = hw->mac.ops.setup_sfp(hw);
		hw->phy.sfp_setup_needed = false;
	}

	/* Reset PHY */
	if (hw->phy.reset_disable == false && hw->phy.ops.reset != NULL)
		hw->phy.ops.reset(hw);

	/*
	 * Prevent the PCI-E bus from from hanging by disabling PCI-E master
	 * access and verify no pending requests before reset
	 */
	status = ixgbe_disable_pcie_master(hw);
	if (status != 0) {
		status = IXGBE_ERR_MASTER_REQUESTS_PENDING;
		hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
	}

	/*
	 * Issue global reset to the MAC.  This needs to be a SW reset.
	 * If link reset is used, it might reset the MAC when mng is using it
	 */
	ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL);
	IXGBE_WRITE_REG(hw, IXGBE_CTRL, (ctrl | IXGBE_CTRL_RST));
	IXGBE_WRITE_FLUSH(hw);

	/* Poll for reset bit to self-clear indicating reset is complete */
	for (i = 0; i < 10; i++) {
		udelay(1);
		ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL);
		if (!(ctrl & IXGBE_CTRL_RST))
			break;
	}
	if (ctrl & IXGBE_CTRL_RST) {
		status = IXGBE_ERR_RESET_FAILED;
		hw_dbg(hw, "Reset polling failed to complete.\n");
	}

	msleep(50);

	/*
	 * Store the original AUTOC/AUTOC2 values if they have not been
	 * stored off yet.  Otherwise restore the stored original
	 * values since the reset operation sets back to defaults.
	 */
	autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
	autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
	if (hw->mac.orig_link_settings_stored == false) {
		hw->mac.orig_autoc = autoc;
		hw->mac.orig_autoc2 = autoc2;
		hw->mac.orig_link_settings_stored = true;
	} else {
		if (autoc != hw->mac.orig_autoc)
			IXGBE_WRITE_REG(hw, IXGBE_AUTOC, (hw->mac.orig_autoc |
			                IXGBE_AUTOC_AN_RESTART));

		if ((autoc2 & IXGBE_AUTOC2_UPPER_MASK) !=
		    (hw->mac.orig_autoc2 & IXGBE_AUTOC2_UPPER_MASK)) {
			autoc2 &= ~IXGBE_AUTOC2_UPPER_MASK;
			autoc2 |= (hw->mac.orig_autoc2 &
			           IXGBE_AUTOC2_UPPER_MASK);
			IXGBE_WRITE_REG(hw, IXGBE_AUTOC2, autoc2);
		}
	}

	/*
	 * Store MAC address from RAR0, clear receive address registers, and
	 * clear the multicast table.  Also reset num_rar_entries to 128,
	 * since we modify this value when programming the SAN MAC address.
	 */
	hw->mac.num_rar_entries = 128;
	hw->mac.ops.init_rx_addrs(hw);

	/* Store the permanent mac address */
	hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);

	/* Store the permanent SAN mac address */
	hw->mac.ops.get_san_mac_addr(hw, hw->mac.san_addr);

	/* Add the SAN MAC address to the RAR only if it's a valid address */
	if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
		hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
		                    hw->mac.san_addr, 0, IXGBE_RAH_AV);

		/* Reserve the last RAR for the SAN MAC address */
		hw->mac.num_rar_entries--;
	}

	/* Store the alternative WWNN/WWPN prefix */
	hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix,
	                               &hw->mac.wwpn_prefix);

reset_hw_out:
	return status;
}

/**
 *  ixgbe_reinit_fdir_tables_82599 - Reinitialize Flow Director tables.
 *  @hw: pointer to hardware structure
 **/
s32 ixgbe_reinit_fdir_tables_82599(struct ixgbe_hw *hw)
{
	int i;
	u32 fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL);
	fdirctrl &= ~IXGBE_FDIRCTRL_INIT_DONE;

	/*
	 * Before starting reinitialization process,
	 * FDIRCMD.CMD must be zero.
	 */
	for (i = 0; i < IXGBE_FDIRCMD_CMD_POLL; i++) {
		if (!(IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
		      IXGBE_FDIRCMD_CMD_MASK))
			break;
		udelay(10);
	}
	if (i >= IXGBE_FDIRCMD_CMD_POLL) {
		hw_dbg(hw ,"Flow Director previous command isn't complete, "
		       "aborting table re-initialization.\n");
		return IXGBE_ERR_FDIR_REINIT_FAILED;
	}

	IXGBE_WRITE_REG(hw, IXGBE_FDIRFREE, 0);
	IXGBE_WRITE_FLUSH(hw);
	/*
	 * 82599 adapters flow director init flow cannot be restarted,
	 * Workaround 82599 silicon errata by performing the following steps
	 * before re-writing the FDIRCTRL control register with the same value.
	 * - write 1 to bit 8 of FDIRCMD register &
	 * - write 0 to bit 8 of FDIRCMD register
	 */
	IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
	                (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) |
	                 IXGBE_FDIRCMD_CLEARHT));
	IXGBE_WRITE_FLUSH(hw);
	IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
	                (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
	                 ~IXGBE_FDIRCMD_CLEARHT));
	IXGBE_WRITE_FLUSH(hw);
	/*
	 * Clear FDIR Hash register to clear any leftover hashes
	 * waiting to be programmed.
	 */
	IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, 0x00);
	IXGBE_WRITE_FLUSH(hw);

	IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl);
	IXGBE_WRITE_FLUSH(hw);

	/* Poll init-done after we write FDIRCTRL register */
	for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) {
		if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) &
		                   IXGBE_FDIRCTRL_INIT_DONE)
			break;
		udelay(10);
	}
	if (i >= IXGBE_FDIR_INIT_DONE_POLL) {
		hw_dbg(hw, "Flow Director Signature poll time exceeded!\n");
		return IXGBE_ERR_FDIR_REINIT_FAILED;
	}

	/* Clear FDIR statistics registers (read to clear) */
	IXGBE_READ_REG(hw, IXGBE_FDIRUSTAT);
	IXGBE_READ_REG(hw, IXGBE_FDIRFSTAT);
	IXGBE_READ_REG(hw, IXGBE_FDIRMATCH);
	IXGBE_READ_REG(hw, IXGBE_FDIRMISS);
	IXGBE_READ_REG(hw, IXGBE_FDIRLEN);

	return 0;
}

/**
 *  ixgbe_init_fdir_signature_82599 - Initialize Flow Director signature filters
 *  @hw: pointer to hardware structure
 *  @pballoc: which mode to allocate filters with
 **/
s32 ixgbe_init_fdir_signature_82599(struct ixgbe_hw *hw, u32 pballoc)
{
	u32 fdirctrl = 0;
	u32 pbsize;
	int i;

	/*
	 * Before enabling Flow Director, the Rx Packet Buffer size
	 * must be reduced.  The new value is the current size minus
	 * flow director memory usage size.
	 */
	pbsize = (1 << (IXGBE_FDIR_PBALLOC_SIZE_SHIFT + pballoc));
	IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(0),
	    (IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(0)) - pbsize));

	/*
	 * The defaults in the HW for RX PB 1-7 are not zero and so should be
	 * intialized to zero for non DCB mode otherwise actual total RX PB
	 * would be bigger than programmed and filter space would run into
	 * the PB 0 region.
	 */
	for (i = 1; i < 8; i++)
		IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0);

	/* Send interrupt when 64 filters are left */
	fdirctrl |= 4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT;

	/* Set the maximum length per hash bucket to 0xA filters */
	fdirctrl |= 0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT;

	switch (pballoc) {
	case IXGBE_FDIR_PBALLOC_64K:
		/* 8k - 1 signature filters */
		fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_64K;
		break;
	case IXGBE_FDIR_PBALLOC_128K:
		/* 16k - 1 signature filters */
		fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_128K;
		break;
	case IXGBE_FDIR_PBALLOC_256K:
		/* 32k - 1 signature filters */
		fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_256K;
		break;
	default:
		/* bad value */
		return IXGBE_ERR_CONFIG;
	};

	/* Move the flexible bytes to use the ethertype - shift 6 words */
	fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT);

	fdirctrl |= IXGBE_FDIRCTRL_REPORT_STATUS;

	/* Prime the keys for hashing */
	IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY,
	                htonl(IXGBE_ATR_BUCKET_HASH_KEY));
	IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY,
	                htonl(IXGBE_ATR_SIGNATURE_HASH_KEY));

	/*
	 * Poll init-done after we write the register.  Estimated times:
	 *      10G: PBALLOC = 11b, timing is 60us
	 *       1G: PBALLOC = 11b, timing is 600us
	 *     100M: PBALLOC = 11b, timing is 6ms
	 *
	 *     Multiple these timings by 4 if under full Rx load
	 *
	 * So we'll poll for IXGBE_FDIR_INIT_DONE_POLL times, sleeping for
	 * 1 msec per poll time.  If we're at line rate and drop to 100M, then
	 * this might not finish in our poll time, but we can live with that
	 * for now.
	 */
	IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl);
	IXGBE_WRITE_FLUSH(hw);
	for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) {
		if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) &
		                   IXGBE_FDIRCTRL_INIT_DONE)
			break;
		msleep(1);
	}
	if (i >= IXGBE_FDIR_INIT_DONE_POLL)
		hw_dbg(hw, "Flow Director Signature poll time exceeded!\n");

	return 0;
}

/**
 *  ixgbe_init_fdir_perfect_82599 - Initialize Flow Director perfect filters
 *  @hw: pointer to hardware structure
 *  @pballoc: which mode to allocate filters with
 **/
s32 ixgbe_init_fdir_perfect_82599(struct ixgbe_hw *hw, u32 pballoc)
{
	u32 fdirctrl = 0;
	u32 pbsize;
	int i;

	/*
	 * Before enabling Flow Director, the Rx Packet Buffer size
	 * must be reduced.  The new value is the current size minus
	 * flow director memory usage size.
	 */
	pbsize = (1 << (IXGBE_FDIR_PBALLOC_SIZE_SHIFT + pballoc));
	IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(0),
	    (IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(0)) - pbsize));

	/*
	 * The defaults in the HW for RX PB 1-7 are not zero and so should be
	 * intialized to zero for non DCB mode otherwise actual total RX PB
	 * would be bigger than programmed and filter space would run into
	 * the PB 0 region.
	 */
	for (i = 1; i < 8; i++)
		IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0);

	/* Send interrupt when 64 filters are left */
	fdirctrl |= 4 << IXGBE_FDIRCTRL_FULL_THRESH_SHIFT;

	/* Initialize the drop queue to Rx queue 127 */
	fdirctrl |= (127 << IXGBE_FDIRCTRL_DROP_Q_SHIFT);

	switch (pballoc) {
	case IXGBE_FDIR_PBALLOC_64K:
		/* 2k - 1 perfect filters */
		fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_64K;
		break;
	case IXGBE_FDIR_PBALLOC_128K:
		/* 4k - 1 perfect filters */
		fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_128K;
		break;
	case IXGBE_FDIR_PBALLOC_256K:
		/* 8k - 1 perfect filters */
		fdirctrl |= IXGBE_FDIRCTRL_PBALLOC_256K;
		break;
	default:
		/* bad value */
		return IXGBE_ERR_CONFIG;
	};

	/* Turn perfect match filtering on */
	fdirctrl |= IXGBE_FDIRCTRL_PERFECT_MATCH;
	fdirctrl |= IXGBE_FDIRCTRL_REPORT_STATUS;

	/* Move the flexible bytes to use the ethertype - shift 6 words */
	fdirctrl |= (0x6 << IXGBE_FDIRCTRL_FLEX_SHIFT);

	/* Prime the keys for hashing */
	IXGBE_WRITE_REG(hw, IXGBE_FDIRHKEY,
	                htonl(IXGBE_ATR_BUCKET_HASH_KEY));
	IXGBE_WRITE_REG(hw, IXGBE_FDIRSKEY,
	                htonl(IXGBE_ATR_SIGNATURE_HASH_KEY));

	/*
	 * Poll init-done after we write the register.  Estimated times:
	 *      10G: PBALLOC = 11b, timing is 60us
	 *       1G: PBALLOC = 11b, timing is 600us
	 *     100M: PBALLOC = 11b, timing is 6ms
	 *
	 *     Multiple these timings by 4 if under full Rx load
	 *
	 * So we'll poll for IXGBE_FDIR_INIT_DONE_POLL times, sleeping for
	 * 1 msec per poll time.  If we're at line rate and drop to 100M, then
	 * this might not finish in our poll time, but we can live with that
	 * for now.
	 */

	/* Set the maximum length per hash bucket to 0xA filters */
	fdirctrl |= (0xA << IXGBE_FDIRCTRL_MAX_LENGTH_SHIFT);

	IXGBE_WRITE_REG(hw, IXGBE_FDIRCTRL, fdirctrl);
	IXGBE_WRITE_FLUSH(hw);
	for (i = 0; i < IXGBE_FDIR_INIT_DONE_POLL; i++) {
		if (IXGBE_READ_REG(hw, IXGBE_FDIRCTRL) &
		                   IXGBE_FDIRCTRL_INIT_DONE)
			break;
		msleep(1);
	}
	if (i >= IXGBE_FDIR_INIT_DONE_POLL)
		hw_dbg(hw, "Flow Director Perfect poll time exceeded!\n");

	return 0;
}


/**
 *  ixgbe_atr_compute_hash_82599 - Compute the hashes for SW ATR
 *  @stream: input bitstream to compute the hash on
 *  @key: 32-bit hash key
 **/
static u16 ixgbe_atr_compute_hash_82599(struct ixgbe_atr_input *atr_input,
                                        u32 key)
{
	/*
	 * The algorithm is as follows:
	 *    Hash[15:0] = Sum { S[n] x K[n+16] }, n = 0...350
	 *    where Sum {A[n]}, n = 0...n is bitwise XOR of A[0], A[1]...A[n]
	 *    and A[n] x B[n] is bitwise AND between same length strings
	 *
	 *    K[n] is 16 bits, defined as:
	 *       for n modulo 32 >= 15, K[n] = K[n % 32 : (n % 32) - 15]
	 *       for n modulo 32 < 15, K[n] =
	 *             K[(n % 32:0) | (31:31 - (14 - (n % 32)))]
	 *
	 *    S[n] is 16 bits, defined as:
	 *       for n >= 15, S[n] = S[n:n - 15]
	 *       for n < 15, S[n] = S[(n:0) | (350:350 - (14 - n))]
	 *
	 *    To simplify for programming, the algorithm is implemented
	 *    in software this way:
	 *
	 *    Key[31:0], Stream[335:0]
	 *
	 *    tmp_key[11 * 32 - 1:0] = 11{Key[31:0] = key concatenated 11 times
	 *    int_key[350:0] = tmp_key[351:1]
	 *    int_stream[365:0] = Stream[14:0] | Stream[335:0] | Stream[335:321]
	 *
	 *    hash[15:0] = 0;
	 *    for (i = 0; i < 351; i++) {
	 *        if (int_key[i])
	 *            hash ^= int_stream[(i + 15):i];
	 *    }
	 */

	union {
		u64    fill[6];
		u32    key[11];
		u8     key_stream[44];
	} tmp_key;

	u8   *stream = (u8 *)atr_input;
	u8   int_key[44];      /* upper-most bit unused */
	u8   hash_str[46];     /* upper-most 2 bits unused */
	u16  hash_result = 0;
	int  i, j, k, h;

	/*
	 * Initialize the fill member to prevent warnings
	 * on some compilers
	 */
	 tmp_key.fill[0] = 0;

	/* First load the temporary key stream */
	for (i = 0; i < 6; i++) {
		u64 fillkey = ((u64)key << 32) | key;
		tmp_key.fill[i] = fillkey;
	}

	/*
	 * Set the interim key for the hashing.  Bit 352 is unused, so we must
	 * shift and compensate when building the key.
	 */

	int_key[0] = tmp_key.key_stream[0] >> 1;
	for (i = 1, j = 0; i < 44; i++) {
		unsigned int this_key = tmp_key.key_stream[j] << 7;
		j++;
		int_key[i] = (u8)(this_key | (tmp_key.key_stream[j] >> 1));
	}

	/*
	 * Set the interim bit string for the hashing.  Bits 368 and 367 are
	 * unused, so shift and compensate when building the string.
	 */
	hash_str[0] = (stream[40] & 0x7f) >> 1;
	for (i = 1, j = 40; i < 46; i++) {
		unsigned int this_str = stream[j] << 7;
		j++;
		if (j > 41)
			j = 0;
		hash_str[i] = (u8)(this_str | (stream[j] >> 1));
	}

	/*
	 * Now compute the hash.  i is the index into hash_str, j is into our
	 * key stream, k is counting the number of bits, and h interates within
	 * each byte.
	 */
	for (i = 45, j = 43, k = 0; k < 351 && i >= 2 && j >= 0; i--, j--) {
		for (h = 0; h < 8 && k < 351; h++, k++) {
			if (int_key[j] & (1 << h)) {
				/*
				 * Key bit is set, XOR in the current 16-bit
				 * string.  Example of processing:
				 *    h = 0,
				 *      tmp = (hash_str[i - 2] & 0 << 16) |
				 *            (hash_str[i - 1] & 0xff << 8) |
				 *            (hash_str[i] & 0xff >> 0)
				 *      So tmp = hash_str[15 + k:k], since the
				 *      i + 2 clause rolls off the 16-bit value
				 *    h = 7,
				 *      tmp = (hash_str[i - 2] & 0x7f << 9) |
				 *            (hash_str[i - 1] & 0xff << 1) |
				 *            (hash_str[i] & 0x80 >> 7)
				 */
				int tmp = (hash_str[i] >> h);
				tmp |= (hash_str[i - 1] << (8 - h));
				tmp |= (int)(hash_str[i - 2] & ((1 << h) - 1))
				             << (16 - h);
				hash_result ^= (u16)tmp;
			}
		}
	}

	return hash_result;
}

/**
 *  ixgbe_atr_set_vlan_id_82599 - Sets the VLAN id in the ATR input stream
 *  @input: input stream to modify
 *  @vlan: the VLAN id to load
 **/
s32 ixgbe_atr_set_vlan_id_82599(struct ixgbe_atr_input *input, u16 vlan)
{
	input->byte_stream[IXGBE_ATR_VLAN_OFFSET + 1] = vlan >> 8;
	input->byte_stream[IXGBE_ATR_VLAN_OFFSET] = vlan & 0xff;

	return 0;
}

/**
 *  ixgbe_atr_set_src_ipv4_82599 - Sets the source IPv4 address
 *  @input: input stream to modify
 *  @src_addr: the IP address to load
 **/
s32 ixgbe_atr_set_src_ipv4_82599(struct ixgbe_atr_input *input, u32 src_addr)
{
	input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 3] = src_addr >> 24;
	input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 2] =
	                                               (src_addr >> 16) & 0xff;
	input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 1] =
	                                                (src_addr >> 8) & 0xff;
	input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET] = src_addr & 0xff;

	return 0;
}

/**
 *  ixgbe_atr_set_dst_ipv4_82599 - Sets the destination IPv4 address
 *  @input: input stream to modify
 *  @dst_addr: the IP address to load
 **/
s32 ixgbe_atr_set_dst_ipv4_82599(struct ixgbe_atr_input *input, u32 dst_addr)
{
	input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 3] = dst_addr >> 24;
	input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 2] =
	                                               (dst_addr >> 16) & 0xff;
	input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 1] =
	                                                (dst_addr >> 8) & 0xff;
	input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET] = dst_addr & 0xff;

	return 0;
}

/**
 *  ixgbe_atr_set_src_port_82599 - Sets the source port
 *  @input: input stream to modify
 *  @src_port: the source port to load
 **/
s32 ixgbe_atr_set_src_port_82599(struct ixgbe_atr_input *input, u16 src_port)
{
	input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET + 1] = src_port >> 8;
	input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET] = src_port & 0xff;

	return 0;
}

/**
 *  ixgbe_atr_set_dst_port_82599 - Sets the destination port
 *  @input: input stream to modify
 *  @dst_port: the destination port to load
 **/
s32 ixgbe_atr_set_dst_port_82599(struct ixgbe_atr_input *input, u16 dst_port)
{
	input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET + 1] = dst_port >> 8;
	input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET] = dst_port & 0xff;

	return 0;
}

/**
 *  ixgbe_atr_set_flex_byte_82599 - Sets the flexible bytes
 *  @input: input stream to modify
 *  @flex_bytes: the flexible bytes to load
 **/
s32 ixgbe_atr_set_flex_byte_82599(struct ixgbe_atr_input *input, u16 flex_byte)
{
	input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET + 1] = flex_byte >> 8;
	input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET] = flex_byte & 0xff;

	return 0;
}

/**
 *  ixgbe_atr_set_l4type_82599 - Sets the layer 4 packet type
 *  @input: input stream to modify
 *  @l4type: the layer 4 type value to load
 **/
s32 ixgbe_atr_set_l4type_82599(struct ixgbe_atr_input *input, u8 l4type)
{
	input->byte_stream[IXGBE_ATR_L4TYPE_OFFSET] = l4type;

	return 0;
}

/**
 *  ixgbe_atr_get_vlan_id_82599 - Gets the VLAN id from the ATR input stream
 *  @input: input stream to search
 *  @vlan: the VLAN id to load
 **/
static s32 ixgbe_atr_get_vlan_id_82599(struct ixgbe_atr_input *input, u16 *vlan)
{
	*vlan = input->byte_stream[IXGBE_ATR_VLAN_OFFSET];
	*vlan |= input->byte_stream[IXGBE_ATR_VLAN_OFFSET + 1] << 8;

	return 0;
}

/**
 *  ixgbe_atr_get_src_ipv4_82599 - Gets the source IPv4 address
 *  @input: input stream to search
 *  @src_addr: the IP address to load
 **/
static s32 ixgbe_atr_get_src_ipv4_82599(struct ixgbe_atr_input *input,
                                        u32 *src_addr)
{
	*src_addr = input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET];
	*src_addr |= input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 1] << 8;
	*src_addr |= input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 2] << 16;
	*src_addr |= input->byte_stream[IXGBE_ATR_SRC_IPV4_OFFSET + 3] << 24;

	return 0;
}

/**
 *  ixgbe_atr_get_dst_ipv4_82599 - Gets the destination IPv4 address
 *  @input: input stream to search
 *  @dst_addr: the IP address to load
 **/
static s32 ixgbe_atr_get_dst_ipv4_82599(struct ixgbe_atr_input *input,
                                        u32 *dst_addr)
{
	*dst_addr = input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET];
	*dst_addr |= input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 1] << 8;
	*dst_addr |= input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 2] << 16;
	*dst_addr |= input->byte_stream[IXGBE_ATR_DST_IPV4_OFFSET + 3] << 24;

	return 0;
}

/**
 *  ixgbe_atr_get_src_ipv6_82599 - Gets the source IPv6 address
 *  @input: input stream to search
 *  @src_addr_1: the first 4 bytes of the IP address to load
 *  @src_addr_2: the second 4 bytes of the IP address to load
 *  @src_addr_3: the third 4 bytes of the IP address to load
 *  @src_addr_4: the fourth 4 bytes of the IP address to load
 **/
static s32 ixgbe_atr_get_src_ipv6_82599(struct ixgbe_atr_input *input,
                                        u32 *src_addr_1, u32 *src_addr_2,
                                        u32 *src_addr_3, u32 *src_addr_4)
{
	*src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 12];
	*src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 13] << 8;
	*src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 14] << 16;
	*src_addr_1 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 15] << 24;

	*src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 8];
	*src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 9] << 8;
	*src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 10] << 16;
	*src_addr_2 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 11] << 24;

	*src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 4];
	*src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 5] << 8;
	*src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 6] << 16;
	*src_addr_3 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 7] << 24;

	*src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET];
	*src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 1] << 8;
	*src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 2] << 16;
	*src_addr_4 = input->byte_stream[IXGBE_ATR_SRC_IPV6_OFFSET + 3] << 24;

	return 0;
}

/**
 *  ixgbe_atr_get_src_port_82599 - Gets the source port
 *  @input: input stream to modify
 *  @src_port: the source port to load
 *
 *  Even though the input is given in big-endian, the FDIRPORT registers
 *  expect the ports to be programmed in little-endian.  Hence the need to swap
 *  endianness when retrieving the data.  This can be confusing since the
 *  internal hash engine expects it to be big-endian.
 **/
static s32 ixgbe_atr_get_src_port_82599(struct ixgbe_atr_input *input,
                                        u16 *src_port)
{
	*src_port = input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET] << 8;
	*src_port |= input->byte_stream[IXGBE_ATR_SRC_PORT_OFFSET + 1];

	return 0;
}

/**
 *  ixgbe_atr_get_dst_port_82599 - Gets the destination port
 *  @input: input stream to modify
 *  @dst_port: the destination port to load
 *
 *  Even though the input is given in big-endian, the FDIRPORT registers
 *  expect the ports to be programmed in little-endian.  Hence the need to swap
 *  endianness when retrieving the data.  This can be confusing since the
 *  internal hash engine expects it to be big-endian.
 **/
static s32 ixgbe_atr_get_dst_port_82599(struct ixgbe_atr_input *input,
                                        u16 *dst_port)
{
	*dst_port = input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET] << 8;
	*dst_port |= input->byte_stream[IXGBE_ATR_DST_PORT_OFFSET + 1];

	return 0;
}

/**
 *  ixgbe_atr_get_flex_byte_82599 - Gets the flexible bytes
 *  @input: input stream to modify
 *  @flex_bytes: the flexible bytes to load
 **/
static s32 ixgbe_atr_get_flex_byte_82599(struct ixgbe_atr_input *input,
                                         u16 *flex_byte)
{
	*flex_byte = input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET];
	*flex_byte |= input->byte_stream[IXGBE_ATR_FLEX_BYTE_OFFSET + 1] << 8;

	return 0;
}

/**
 *  ixgbe_atr_get_l4type_82599 - Gets the layer 4 packet type
 *  @input: input stream to modify
 *  @l4type: the layer 4 type value to load
 **/
static s32 ixgbe_atr_get_l4type_82599(struct ixgbe_atr_input *input,
                                      u8 *l4type)
{
	*l4type = input->byte_stream[IXGBE_ATR_L4TYPE_OFFSET];

	return 0;
}

/**
 *  ixgbe_atr_add_signature_filter_82599 - Adds a signature hash filter
 *  @hw: pointer to hardware structure
 *  @stream: input bitstream
 *  @queue: queue index to direct traffic to
 **/
s32 ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw,
                                          struct ixgbe_atr_input *input,
                                          u8 queue)
{
	u64  fdirhashcmd;
	u64  fdircmd;
	u32  fdirhash;
	u16  bucket_hash, sig_hash;
	u8   l4type;

	bucket_hash = ixgbe_atr_compute_hash_82599(input,
	                                           IXGBE_ATR_BUCKET_HASH_KEY);

	/* bucket_hash is only 15 bits */
	bucket_hash &= IXGBE_ATR_HASH_MASK;

	sig_hash = ixgbe_atr_compute_hash_82599(input,
	                                        IXGBE_ATR_SIGNATURE_HASH_KEY);

	/* Get the l4type in order to program FDIRCMD properly */
	/* lowest 2 bits are FDIRCMD.L4TYPE, third lowest bit is FDIRCMD.IPV6 */
	ixgbe_atr_get_l4type_82599(input, &l4type);

	/*
	 * The lower 32-bits of fdirhashcmd is for FDIRHASH, the upper 32-bits
	 * is for FDIRCMD.  Then do a 64-bit register write from FDIRHASH.
	 */
	fdirhash = sig_hash << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT | bucket_hash;

	fdircmd = (IXGBE_FDIRCMD_CMD_ADD_FLOW | IXGBE_FDIRCMD_FILTER_UPDATE |
	           IXGBE_FDIRCMD_LAST | IXGBE_FDIRCMD_QUEUE_EN);

	switch (l4type & IXGBE_ATR_L4TYPE_MASK) {
	case IXGBE_ATR_L4TYPE_TCP:
		fdircmd |= IXGBE_FDIRCMD_L4TYPE_TCP;
		break;
	case IXGBE_ATR_L4TYPE_UDP:
		fdircmd |= IXGBE_FDIRCMD_L4TYPE_UDP;
		break;
	case IXGBE_ATR_L4TYPE_SCTP:
		fdircmd |= IXGBE_FDIRCMD_L4TYPE_SCTP;
		break;
	default:
		hw_dbg(hw, "Error on l4type input\n");
		return IXGBE_ERR_CONFIG;
	}

	if (l4type & IXGBE_ATR_L4TYPE_IPV6_MASK)
		fdircmd |= IXGBE_FDIRCMD_IPV6;

	fdircmd |= ((u64)queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT);
	fdirhashcmd = ((fdircmd << 32) | fdirhash);

	IXGBE_WRITE_REG64(hw, IXGBE_FDIRHASH, fdirhashcmd);

	return 0;
}

/**
 *  ixgbe_fdir_add_perfect_filter_82599 - Adds a perfect filter
 *  @hw: pointer to hardware structure
 *  @input: input bitstream
 *  @input_masks: bitwise masks for relevant fields
 *  @soft_id: software index into the silicon hash tables for filter storage
 *  @queue: queue index to direct traffic to
 *
 *  Note that the caller to this function must lock before calling, since the
 *  hardware writes must be protected from one another.
 **/
s32 ixgbe_fdir_add_perfect_filter_82599(struct ixgbe_hw *hw,
                                      struct ixgbe_atr_input *input,
                                      struct ixgbe_atr_input_masks *input_masks,
                                      u16 soft_id, u8 queue)
{
	u32 fdircmd = 0;
	u32 fdirhash;
	u32 src_ipv4 = 0, dst_ipv4 = 0;
	u32 src_ipv6_1, src_ipv6_2, src_ipv6_3, src_ipv6_4;
	u16 src_port, dst_port, vlan_id, flex_bytes;
	u16 bucket_hash;
	u8  l4type;
	u8  fdirm = 0;

	/* Get our input values */
	ixgbe_atr_get_l4type_82599(input, &l4type);

	/*
	 * Check l4type formatting, and bail out before we touch the hardware
	 * if there's a configuration issue
	 */
	switch (l4type & IXGBE_ATR_L4TYPE_MASK) {
	case IXGBE_ATR_L4TYPE_TCP:
		fdircmd |= IXGBE_FDIRCMD_L4TYPE_TCP;
		break;
	case IXGBE_ATR_L4TYPE_UDP:
		fdircmd |= IXGBE_FDIRCMD_L4TYPE_UDP;
		break;
	case IXGBE_ATR_L4TYPE_SCTP:
		fdircmd |= IXGBE_FDIRCMD_L4TYPE_SCTP;
		break;
	default:
		hw_dbg(hw, "Error on l4type input\n");
		return IXGBE_ERR_CONFIG;
	}

	bucket_hash = ixgbe_atr_compute_hash_82599(input,
	                                           IXGBE_ATR_BUCKET_HASH_KEY);

	/* bucket_hash is only 15 bits */
	bucket_hash &= IXGBE_ATR_HASH_MASK;

	ixgbe_atr_get_vlan_id_82599(input, &vlan_id);
	ixgbe_atr_get_src_port_82599(input, &src_port);
	ixgbe_atr_get_dst_port_82599(input, &dst_port);
	ixgbe_atr_get_flex_byte_82599(input, &flex_bytes);

	fdirhash = soft_id << IXGBE_FDIRHASH_SIG_SW_INDEX_SHIFT | bucket_hash;

	/* Now figure out if we're IPv4 or IPv6 */
	if (l4type & IXGBE_ATR_L4TYPE_IPV6_MASK) {
		/* IPv6 */
		ixgbe_atr_get_src_ipv6_82599(input, &src_ipv6_1, &src_ipv6_2,
	                                     &src_ipv6_3, &src_ipv6_4);

		IXGBE_WRITE_REG(hw, IXGBE_FDIRSIPv6(0), src_ipv6_1);
		IXGBE_WRITE_REG(hw, IXGBE_FDIRSIPv6(1), src_ipv6_2);
		IXGBE_WRITE_REG(hw, IXGBE_FDIRSIPv6(2), src_ipv6_3);
		/* The last 4 bytes is the same register as IPv4 */
		IXGBE_WRITE_REG(hw, IXGBE_FDIRIPSA, src_ipv6_4);

		fdircmd |= IXGBE_FDIRCMD_IPV6;
		fdircmd |= IXGBE_FDIRCMD_IPv6DMATCH;
	} else {
		/* IPv4 */
		ixgbe_atr_get_src_ipv4_82599(input, &src_ipv4);
		IXGBE_WRITE_REG(hw, IXGBE_FDIRIPSA, src_ipv4);
	}

	ixgbe_atr_get_dst_ipv4_82599(input, &dst_ipv4);
	IXGBE_WRITE_REG(hw, IXGBE_FDIRIPDA, dst_ipv4);

	IXGBE_WRITE_REG(hw, IXGBE_FDIRVLAN, (vlan_id |
	                            (flex_bytes << IXGBE_FDIRVLAN_FLEX_SHIFT)));
	IXGBE_WRITE_REG(hw, IXGBE_FDIRPORT, (src_port |
	              (dst_port << IXGBE_FDIRPORT_DESTINATION_SHIFT)));

	/*
	 * Program the relevant mask registers.  L4type cannot be
	 * masked out in this implementation.
	 *
	 * This also assumes IPv4 only.  IPv6 masking isn't supported at this
	 * point in time.
	 */
	IXGBE_WRITE_REG(hw, IXGBE_FDIRSIP4M, input_masks->src_ip_mask);
	IXGBE_WRITE_REG(hw, IXGBE_FDIRDIP4M, input_masks->dst_ip_mask);

	switch (l4type & IXGBE_ATR_L4TYPE_MASK) {
	case IXGBE_ATR_L4TYPE_TCP:
		IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, input_masks->src_port_mask);
		IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM,
				(IXGBE_READ_REG(hw, IXGBE_FDIRTCPM) |
				 (input_masks->dst_port_mask << 16)));
		break;
	case IXGBE_ATR_L4TYPE_UDP:
		IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, input_masks->src_port_mask);
		IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM,
				(IXGBE_READ_REG(hw, IXGBE_FDIRUDPM) |
				 (input_masks->src_port_mask << 16)));
		break;
	default:
		/* this already would have failed above */
		break;
	}

	/* Program the last mask register, FDIRM */
	if (input_masks->vlan_id_mask)
		/* Mask both VLAN and VLANP - bits 0 and 1 */
		fdirm |= 0x3;

	if (input_masks->data_mask)
		/* Flex bytes need masking, so mask the whole thing - bit 4 */
		fdirm |= 0x10;

	/* Now mask VM pool and destination IPv6 - bits 5 and 2 */
	fdirm |= 0x24;

	IXGBE_WRITE_REG(hw, IXGBE_FDIRM, fdirm);

	fdircmd |= IXGBE_FDIRCMD_CMD_ADD_FLOW;
	fdircmd |= IXGBE_FDIRCMD_FILTER_UPDATE;
	fdircmd |= IXGBE_FDIRCMD_LAST;
	fdircmd |= IXGBE_FDIRCMD_QUEUE_EN;
	fdircmd |= queue << IXGBE_FDIRCMD_RX_QUEUE_SHIFT;

	IXGBE_WRITE_REG(hw, IXGBE_FDIRHASH, fdirhash);
	IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD, fdircmd);

	return 0;
}
/**
 *  ixgbe_read_analog_reg8_82599 - Reads 8 bit Omer analog register
 *  @hw: pointer to hardware structure
 *  @reg: analog register to read
 *  @val: read value
 *
 *  Performs read operation to Omer analog register specified.
 **/
static s32 ixgbe_read_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 *val)
{
	u32  core_ctl;

	IXGBE_WRITE_REG(hw, IXGBE_CORECTL, IXGBE_CORECTL_WRITE_CMD |
	                (reg << 8));
	IXGBE_WRITE_FLUSH(hw);
	udelay(10);
	core_ctl = IXGBE_READ_REG(hw, IXGBE_CORECTL);
	*val = (u8)core_ctl;

	return 0;
}

/**
 *  ixgbe_write_analog_reg8_82599 - Writes 8 bit Omer analog register
 *  @hw: pointer to hardware structure
 *  @reg: atlas register to write
 *  @val: value to write
 *
 *  Performs write operation to Omer analog register specified.
 **/
static s32 ixgbe_write_analog_reg8_82599(struct ixgbe_hw *hw, u32 reg, u8 val)
{
	u32  core_ctl;

	core_ctl = (reg << 8) | val;
	IXGBE_WRITE_REG(hw, IXGBE_CORECTL, core_ctl);
	IXGBE_WRITE_FLUSH(hw);
	udelay(10);

	return 0;
}

/**
 *  ixgbe_start_hw_82599 - Prepare hardware for Tx/Rx
 *  @hw: pointer to hardware structure
 *
 *  Starts the hardware using the generic start_hw function.
 *  Then performs device-specific:
 *  Clears the rate limiter registers.
 **/
static s32 ixgbe_start_hw_82599(struct ixgbe_hw *hw)
{
	u32 q_num;
	s32 ret_val;

	ret_val = ixgbe_start_hw_generic(hw);

	/* Clear the rate limiters */
	for (q_num = 0; q_num < hw->mac.max_tx_queues; q_num++) {
		IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, q_num);
		IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0);
	}
	IXGBE_WRITE_FLUSH(hw);

	/* We need to run link autotry after the driver loads */
	hw->mac.autotry_restart = true;

	if (ret_val == 0)
		ret_val = ixgbe_verify_fw_version_82599(hw);

	return ret_val;
}

/**
 *  ixgbe_identify_phy_82599 - Get physical layer module
 *  @hw: pointer to hardware structure
 *
 *  Determines the physical layer module found on the current adapter.
 **/
static s32 ixgbe_identify_phy_82599(struct ixgbe_hw *hw)
{
	s32 status = IXGBE_ERR_PHY_ADDR_INVALID;
	status = ixgbe_identify_phy_generic(hw);
	if (status != 0)
		status = ixgbe_identify_sfp_module_generic(hw);
	return status;
}

/**
 *  ixgbe_get_supported_physical_layer_82599 - Returns physical layer type
 *  @hw: pointer to hardware structure
 *
 *  Determines physical layer capabilities of the current configuration.
 **/
static u32 ixgbe_get_supported_physical_layer_82599(struct ixgbe_hw *hw)
{
	u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
	u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
	u32 autoc2 = IXGBE_READ_REG(hw, IXGBE_AUTOC2);
	u32 pma_pmd_10g_serial = autoc2 & IXGBE_AUTOC2_10G_SERIAL_PMA_PMD_MASK;
	u32 pma_pmd_10g_parallel = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK;
	u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
	u16 ext_ability = 0;
	u8 comp_codes_10g = 0;
	u8 comp_codes_1g = 0;

	hw->phy.ops.identify(hw);

	if (hw->phy.type == ixgbe_phy_tn ||
	    hw->phy.type == ixgbe_phy_cu_unknown) {
		hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
				     &ext_ability);
		if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
			physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
		if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
			physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
		if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
			physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
		goto out;
	}

	switch (autoc & IXGBE_AUTOC_LMS_MASK) {
	case IXGBE_AUTOC_LMS_1G_AN:
	case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
		if (pma_pmd_1g == IXGBE_AUTOC_1G_KX_BX) {
			physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX |
			    IXGBE_PHYSICAL_LAYER_1000BASE_BX;
			goto out;
		} else
			/* SFI mode so read SFP module */
			goto sfp_check;
		break;
	case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
		if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_CX4)
			physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
		else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_KX4)
			physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
		else if (pma_pmd_10g_parallel == IXGBE_AUTOC_10G_XAUI)
			physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_XAUI;
		goto out;
		break;
	case IXGBE_AUTOC_LMS_10G_SERIAL:
		if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_KR) {
			physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR;
			goto out;
		} else if (pma_pmd_10g_serial == IXGBE_AUTOC2_10G_SFI)
			goto sfp_check;
		break;
	case IXGBE_AUTOC_LMS_KX4_KX_KR:
	case IXGBE_AUTOC_LMS_KX4_KX_KR_1G_AN:
		if (autoc & IXGBE_AUTOC_KX_SUPP)
			physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX;
		if (autoc & IXGBE_AUTOC_KX4_SUPP)
			physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
		if (autoc & IXGBE_AUTOC_KR_SUPP)
			physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KR;
		goto out;
		break;
	default:
		goto out;
		break;
	}

sfp_check:
	/* SFP check must be done last since DA modules are sometimes used to
	 * test KR mode -  we need to id KR mode correctly before SFP module.
	 * Call identify_sfp because the pluggable module may have changed */
	hw->phy.ops.identify_sfp(hw);
	if (hw->phy.sfp_type == ixgbe_sfp_type_not_present)
		goto out;

	switch (hw->phy.type) {
	case ixgbe_phy_sfp_passive_tyco:
	case ixgbe_phy_sfp_passive_unknown:
		physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
		break;
	case ixgbe_phy_sfp_ftl_active:
	case ixgbe_phy_sfp_active_unknown:
		physical_layer = IXGBE_PHYSICAL_LAYER_SFP_ACTIVE_DA;
		break;
	case ixgbe_phy_sfp_avago:
	case ixgbe_phy_sfp_ftl:
	case ixgbe_phy_sfp_intel:
	case ixgbe_phy_sfp_unknown:
		hw->phy.ops.read_i2c_eeprom(hw,
		      IXGBE_SFF_1GBE_COMP_CODES, &comp_codes_1g);
		hw->phy.ops.read_i2c_eeprom(hw,
		      IXGBE_SFF_10GBE_COMP_CODES, &comp_codes_10g);
		if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)
			physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
		else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE)
			physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
		else if (comp_codes_1g & IXGBE_SFF_1GBASET_CAPABLE)
			physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_T;
		break;
	default:
		break;
	}

out:
	return physical_layer;
}

/**
 *  ixgbe_enable_rx_dma_82599 - Enable the Rx DMA unit on 82599
 *  @hw: pointer to hardware structure
 *  @regval: register value to write to RXCTRL
 *
 *  Enables the Rx DMA unit for 82599
 **/
static s32 ixgbe_enable_rx_dma_82599(struct ixgbe_hw *hw, u32 regval)
{
#define IXGBE_MAX_SECRX_POLL 30
	int i;
	int secrxreg;

	/*
	 * Workaround for 82599 silicon errata when enabling the Rx datapath.
	 * If traffic is incoming before we enable the Rx unit, it could hang
	 * the Rx DMA unit.  Therefore, make sure the security engine is
	 * completely disabled prior to enabling the Rx unit.
	 */
	secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
	secrxreg |= IXGBE_SECRXCTRL_RX_DIS;
	IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
	for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) {
		secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT);
		if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY)
			break;
		else
			udelay(10);
	}

	/* For informational purposes only */
	if (i >= IXGBE_MAX_SECRX_POLL)
		hw_dbg(hw, "Rx unit being enabled before security "
		       "path fully disabled.  Continuing with init.\n");

	IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, regval);
	secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
	secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS;
	IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
	IXGBE_WRITE_FLUSH(hw);

	return 0;
}

/**
 *  ixgbe_get_device_caps_82599 - Get additional device capabilities
 *  @hw: pointer to hardware structure
 *  @device_caps: the EEPROM word with the extra device capabilities
 *
 *  This function will read the EEPROM location for the device capabilities,
 *  and return the word through device_caps.
 **/
static s32 ixgbe_get_device_caps_82599(struct ixgbe_hw *hw, u16 *device_caps)
{
	hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps);

	return 0;
}

/**
 *  ixgbe_verify_fw_version_82599 - verify fw version for 82599
 *  @hw: pointer to hardware structure
 *
 *  Verifies that installed the firmware version is 0.6 or higher
 *  for SFI devices. All 82599 SFI devices should have version 0.6 or higher.
 *
 *  Returns IXGBE_ERR_EEPROM_VERSION if the FW is not present or
 *  if the FW version is not supported.
 **/
static s32 ixgbe_verify_fw_version_82599(struct ixgbe_hw *hw)
{
	s32 status = IXGBE_ERR_EEPROM_VERSION;
	u16 fw_offset, fw_ptp_cfg_offset;
	u16 fw_version = 0;

	/* firmware check is only necessary for SFI devices */
	if (hw->phy.media_type != ixgbe_media_type_fiber) {
		status = 0;
		goto fw_version_out;
	}

	/* get the offset to the Firmware Module block */
	hw->eeprom.ops.read(hw, IXGBE_FW_PTR, &fw_offset);

	if ((fw_offset == 0) || (fw_offset == 0xFFFF))
		goto fw_version_out;

	/* get the offset to the Pass Through Patch Configuration block */
	hw->eeprom.ops.read(hw, (fw_offset +
	                         IXGBE_FW_PASSTHROUGH_PATCH_CONFIG_PTR),
	                         &fw_ptp_cfg_offset);

	if ((fw_ptp_cfg_offset == 0) || (fw_ptp_cfg_offset == 0xFFFF))
		goto fw_version_out;

	/* get the firmware version */
	hw->eeprom.ops.read(hw, (fw_ptp_cfg_offset +
	                         IXGBE_FW_PATCH_VERSION_4),
	                         &fw_version);

	if (fw_version > 0x5)
		status = 0;

fw_version_out:
	return status;
}

/**
 *  ixgbe_get_wwn_prefix_82599 - Get alternative WWNN/WWPN prefix from
 *  the EEPROM
 *  @hw: pointer to hardware structure
 *  @wwnn_prefix: the alternative WWNN prefix
 *  @wwpn_prefix: the alternative WWPN prefix
 *
 *  This function will read the EEPROM from the alternative SAN MAC address
 *  block to check the support for the alternative WWNN/WWPN prefix support.
 **/
static s32 ixgbe_get_wwn_prefix_82599(struct ixgbe_hw *hw, u16 *wwnn_prefix,
                                      u16 *wwpn_prefix)
{
	u16 offset, caps;
	u16 alt_san_mac_blk_offset;

	/* clear output first */
	*wwnn_prefix = 0xFFFF;
	*wwpn_prefix = 0xFFFF;

	/* check if alternative SAN MAC is supported */
	hw->eeprom.ops.read(hw, IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR,
	                    &alt_san_mac_blk_offset);

	if ((alt_san_mac_blk_offset == 0) ||
	    (alt_san_mac_blk_offset == 0xFFFF))
		goto wwn_prefix_out;

	/* check capability in alternative san mac address block */
	offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET;
	hw->eeprom.ops.read(hw, offset, &caps);
	if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN))
		goto wwn_prefix_out;

	/* get the corresponding prefix for WWNN/WWPN */
	offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET;
	hw->eeprom.ops.read(hw, offset, wwnn_prefix);

	offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET;
	hw->eeprom.ops.read(hw, offset, wwpn_prefix);

wwn_prefix_out:
	return 0;
}

static struct ixgbe_mac_operations mac_ops_82599 = {
	.init_hw                = &ixgbe_init_hw_generic,
	.reset_hw               = &ixgbe_reset_hw_82599,
	.start_hw               = &ixgbe_start_hw_82599,
	.clear_hw_cntrs         = &ixgbe_clear_hw_cntrs_generic,
	.get_media_type         = &ixgbe_get_media_type_82599,
	.get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82599,
	.enable_rx_dma          = &ixgbe_enable_rx_dma_82599,
	.get_mac_addr           = &ixgbe_get_mac_addr_generic,
	.get_san_mac_addr       = &ixgbe_get_san_mac_addr_generic,
	.get_device_caps        = &ixgbe_get_device_caps_82599,
	.get_wwn_prefix         = &ixgbe_get_wwn_prefix_82599,
	.stop_adapter           = &ixgbe_stop_adapter_generic,
	.get_bus_info           = &ixgbe_get_bus_info_generic,
	.set_lan_id             = &ixgbe_set_lan_id_multi_port_pcie,
	.read_analog_reg8       = &ixgbe_read_analog_reg8_82599,
	.write_analog_reg8      = &ixgbe_write_analog_reg8_82599,
	.setup_link             = &ixgbe_setup_mac_link_82599,
	.check_link             = &ixgbe_check_mac_link_generic,
	.get_link_capabilities  = &ixgbe_get_link_capabilities_82599,
	.led_on                 = &ixgbe_led_on_generic,
	.led_off                = &ixgbe_led_off_generic,
	.blink_led_start        = &ixgbe_blink_led_start_generic,
	.blink_led_stop         = &ixgbe_blink_led_stop_generic,
	.set_rar                = &ixgbe_set_rar_generic,
	.clear_rar              = &ixgbe_clear_rar_generic,
	.set_vmdq               = &ixgbe_set_vmdq_generic,
	.clear_vmdq             = &ixgbe_clear_vmdq_generic,
	.init_rx_addrs          = &ixgbe_init_rx_addrs_generic,
	.update_uc_addr_list    = &ixgbe_update_uc_addr_list_generic,
	.update_mc_addr_list    = &ixgbe_update_mc_addr_list_generic,
	.enable_mc              = &ixgbe_enable_mc_generic,
	.disable_mc             = &ixgbe_disable_mc_generic,
	.clear_vfta             = &ixgbe_clear_vfta_generic,
	.set_vfta               = &ixgbe_set_vfta_generic,
	.fc_enable              = &ixgbe_fc_enable_generic,
	.init_uta_tables        = &ixgbe_init_uta_tables_generic,
	.setup_sfp              = &ixgbe_setup_sfp_modules_82599,
};

static struct ixgbe_eeprom_operations eeprom_ops_82599 = {
	.init_params            = &ixgbe_init_eeprom_params_generic,
	.read                   = &ixgbe_read_eerd_generic,
	.write                  = &ixgbe_write_eeprom_generic,
	.validate_checksum      = &ixgbe_validate_eeprom_checksum_generic,
	.update_checksum        = &ixgbe_update_eeprom_checksum_generic,
};

static struct ixgbe_phy_operations phy_ops_82599 = {
	.identify               = &ixgbe_identify_phy_82599,
	.identify_sfp           = &ixgbe_identify_sfp_module_generic,
	.init			            = &ixgbe_init_phy_ops_82599,
	.reset                  = &ixgbe_reset_phy_generic,
	.read_reg               = &ixgbe_read_phy_reg_generic,
	.write_reg              = &ixgbe_write_phy_reg_generic,
	.setup_link             = &ixgbe_setup_phy_link_generic,
	.setup_link_speed       = &ixgbe_setup_phy_link_speed_generic,
	.read_i2c_byte          = &ixgbe_read_i2c_byte_generic,
	.write_i2c_byte         = &ixgbe_write_i2c_byte_generic,
	.read_i2c_eeprom        = &ixgbe_read_i2c_eeprom_generic,
	.write_i2c_eeprom       = &ixgbe_write_i2c_eeprom_generic,
	.check_overtemp         = &ixgbe_tn_check_overtemp,
};

struct ixgbe_info ixgbe_82599_info = {
	.mac                    = ixgbe_mac_82599EB,
	.get_invariants         = &ixgbe_get_invariants_82599,
	.mac_ops                = &mac_ops_82599,
	.eeprom_ops             = &eeprom_ops_82599,
	.phy_ops                = &phy_ops_82599,
	.mbx_ops                = &mbx_ops_82599,
};