Freescale i.MX DRM master device
================================

The freescale i.MX DRM master device is a virtual device needed to list all
IPU or other display interface nodes that comprise the graphics subsystem.

Required properties:
- compatible: Should be "fsl,imx-display-subsystem"
- ports: Should contain a list of phandles pointing to display interface ports
  of IPU devices

example:

display-subsystem {
	compatible = "fsl,display-subsystem";
	ports = <&ipu_di0>;
};


Freescale i.MX IPUv3
====================

Required properties:
- compatible: Should be "fsl,<chip>-ipu"
- reg: should be register base and length as documented in the
  datasheet
- interrupts: Should contain sync interrupt and error interrupt,
  in this order.
- resets: phandle pointing to the system reset controller and
          reset line index, see reset/fsl,imx-src.txt for details
Optional properties:
- port@[0-3]: Port nodes with endpoint definitions as defined in
  Documentation/devicetree/bindings/media/video-interfaces.txt.
  Ports 0 and 1 should correspond to CSI0 and CSI1,
  ports 2 and 3 should correspond to DI0 and DI1, respectively.

example:

ipu: ipu@18000000 {
	#address-cells = <1>;
	#size-cells = <0>;
	compatible = "fsl,imx53-ipu";
	reg = <0x18000000 0x080000000>;
	interrupts = <11 10>;
	resets = <&src 2>;

	ipu_di0: port@2 {
		reg = <2>;

		ipu_di0_disp0: endpoint {
			remote-endpoint = <&display_in>;
		};
	};
};

Freescale i.MX DPU
====================

Required properties:
- compatible: Should be "fsl,<chip>-dpu"
- reg: should be register base and length as documented in the
  datasheet
- intsteer: phandle pointing to interrupt steer.
- interrupts, interrupt-names: Should contain interrupts and names as
  documented in the datasheet.
- clocks, clock-names: phandles to the DPU clocks described in
  Documentation/devicetree/bindings/clock/clock-bindings.txt
  The following clocks are expected on i.MX8qm and i.MX8qxp:
           "pll0" - PLL clock for display interface 0
           "pll1" - PLL clock for display interface 1
           "disp0" - pixel clock for display interface 0
           "disp1" - pixel clock for display interface 1
  The needed clock numbers for each are documented in
  Documentation/devicetree/bindings/clock/imx8qm-clock.txt, and in
  Documentation/devicetree/bindings/clock/imx8qxp-clock.txt.
- power-domains: phandle pointing to power domain.
- fsl,dpr-channels: phandles to the DPR channels attached to this DPU,
  sorted by memory map addresses.  Only valid for i.MX8qm and i.MX8qxp.
Optional properties:
- port@[0-1]: Port nodes with endpoint definitions as defined in
  Documentation/devicetree/bindings/media/video-interfaces.txt.
  ports 0 and 1 should correspond to display interface 0 and
  display interface 1, respectively.

example:

dpu: dpu@56180000 {
	#address-cells = <1>;
	#size-cells = <0>;
	compatible = "fsl,imx8qm-dpu";
	reg = <0x0 0x56180000 0x0 0x40000>;
	intsteer = <&dpu1_intsteer>;
	interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
		     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
	interrupt-names = "irq_common",
			  "irq_stream0a",
			  "irq_stream0b",
			  "irq_stream1a",
			  "irq_stream1b",
			  "irq_reserved0",
			  "irq_reserved1",
			  "irq_blit";
	clocks = <&clk IMX8QM_DC0_PLL0_CLK>,
		 <&clk IMX8QM_DC0_PLL1_CLK>,
		 <&clk IMX8QM_DC0_DISP0_CLK>,
		 <&clk IMX8QM_DC0_DISP1_CLK>;
	clock-names = "pll0", "pll1", "disp0", "disp1";
	power-domains = <&pd_dc0>;
	fsl,dpr-channels = <&dpr1_channel1>, <&dpr1_channel2>,
			   <&dpr1_channel3>, <&dpr2_channel1>,
			   <&dpr2_channel2>, <&dpr2_channel3>;

	dpu1_disp1: port@1 {
		reg = <1>;

		dpu1_disp1_lvds0: lvds0-endpoint {
			remote-endpoint = <&ldb1_lvds0>;
		};

		dpu1_disp1_lvds1: lvds1-endpoint {
			remote-endpoint = <&ldb1_lvds1>;
		};
	};
};


NXP i.MX Display Controller Subsystem (DCSS)
=============================================

Required properties:
- compatible: Should be "nxp,<chip>-dcss"
- reg: should be register base and length as documented in the
  datasheet.
- interrupts, interrupt-names: Should contain interrupts and names as
  documented in the datasheet.
- interrupt-parent: contains the phandle to IRQ Steer module.
- clocks, clock-names: phandles to the DCSS clocks described in
  Documentation/devicetree/bindings/clock/clock-bindings.txt
- disp-dev: can take following values:
      - hdmi_disp: DCSS output goes to HDMI
	  - mipi_disp: DCSS output goes to MIPI_DSI
Optional properties:
- port@[0-1]: Port nodes with endpoint definitions as defined in
  Documentation/devicetree/bindings/media/video-interfaces.txt.
  ports 0 and 1 should correspond to display interface 0 and
  display interface 1, respectively.


example:

dcss_drm: dcss@0x32e00000 {
	#address-cells = <1>;
	#size-cells = <0>;
	compatible = "nxp,imx8mq-dcss";
	reg = <0x0 0x32e00000 0x0 0x30000>;
	interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>, <5 IRQ_TYPE_LEVEL_HIGH>,
			     <6 IRQ_TYPE_LEVEL_HIGH>, <8 IRQ_TYPE_EDGE_RISING>;
	interrupt-names = "dpr_dc_ch0", "dpr_dc_ch1", "dpr_dc_ch2", "ctx_ld",
					  "dtg_prg1";
	interrupt-parent = <&irqsteer_dcss>;
	clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>,
		 <&clk IMX8MQ_CLK_DISP_AXI_ROOT>,
		 <&clk IMX8MQ_CLK_DISP_RTRM_ROOT>,
		 <&clk IMX8MQ_CLK_DC_PIXEL_DIV>,
		 <&clk IMX8MQ_CLK_DISP_DTRC_DIV>;
	clock-names = "apb", "axi", "rtrm", "pixel", "dtrc";
	assigned-clocks = <&clk IMX8MQ_CLK_DISP_APB_SRC>,
			  <&clk IMX8MQ_CLK_DISP_AXI_SRC>,
			  <&clk IMX8MQ_CLK_DISP_RTRM_SRC>,
			  <&clk IMX8MQ_CLK_DC_PIXEL_SRC>,
			  <&clk IMX8MQ_CLK_DISP_DTRC_SRC>;
	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>,
				 <&clk IMX8MQ_SYS1_PLL_800M>,
				 <&clk IMX8MQ_SYS1_PLL_800M>,
				 <&clk IMX8MQ_VIDEO_PLL1_OUT>,
				 <&clk IMX8MQ_CLK_25M>;
	assigned-clock-rate = <800000000>, <800000000>, <800000000>, <594000000>, <25000000>;

	disp-dev = "hdmi_disp";

	status = "okay";

	dcss_disp0: port@0 {
		reg = <0>;

		dcss_disp0_imx_stub: imx_stub_conenc {
			remote-endpoint = <&imx_stub_conenc0>;
		};
	};
};

Freescale i.MX8 PRG (Prefetch Resolve Gasket)
=============================================
Required properties:
- compatible: should be "fsl,<chip>-prg"
- reg: should be register base and length as documented in the
  datasheet
- clocks: phandles to the PRG apb and rtram clocks, as described in
  Documentation/devicetree/bindings/clock/clock-bindings.txt,
  Documentation/devicetree/bindings/clock/imx8qm-clock.txt and
  Documentation/devicetree/bindings/clock/imx8qxp-clock.txt
- clock-names: should be "apb" and "rtram"
- power-domains: phandle pointing to power domain

example:

prg@56040000 {
	compatible = "fsl,imx8qm-prg";
	reg = <0x0 0x56040000 0x0 0x10000>;
	clocks = <&clk IMX8QM_DC0_PRG0_APB_CLK>,
		 <&clk IMX8QM_DC0_PRG0_RTRAM_CLK>;
	clock-names = "apb", "rtram";
	power-domains = <&pd_dc0>;
};

Freescale i.MX8 DPRC (Display Prefetch Resolve Channel)
=======================================================
Required properties:
- compatible: should be "fsl,<chip>-dpr-channel"
- reg: should be register base and length as documented in the
  datasheet
- fsl,sc-resource: SCU resource number as described in
  Documentation/devicetree/bindings/soc/fsl/imx_rsrc.txt
- fsl,prgs: phandles to the PRG unit(s) attached to this DPRC, the first one
  is the primary PRG and the second one(if available) is the auxiliary PRG
  which is used to fetch luma chunk of a YUV frame with 2 planars.
- clocks: phandles to the DPRC apb, b and rtram clocks, as described in
  Documentation/devicetree/bindings/clock/clock-bindings.txt,
  Documentation/devicetree/bindings/clock/imx8qm-clock.txt and
  Documentation/devicetree/bindings/clock/imx8qxp-clock.txt
- clock-names: should be "apb", "b" and "rtram"
- power-domains: phandle pointing to power domain

example:

dpr-channel@56100000 {
	compatible = "fsl,imx8qm-dpr-channel";
	reg = <0x0 0x56100000 0x0 0x10000>;
	fsl,sc-resource = <SC_R_DC_0_VIDEO0>;
	fsl,prgs = <&prg4>, <&prg5>;
	clocks = <&clk IMX8QM_DC0_DPR1_APB_CLK>,
		 <&clk IMX8QM_DC0_DPR1_B_CLK>,
		 <&clk IMX8QM_DC0_RTRAM1_CLK>;
	clock-names = "apb", "b", "rtram";
	power-domains = <&pd_dc0>;
};

Parallel display support
========================

Required properties:
- compatible: Should be "fsl,imx-parallel-display"
Optional properties:
- interface_pix_fmt: How this display is connected to the
  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
  and "lvds666".
- edid: verbatim EDID data block describing attached display.
- ddc: phandle describing the i2c bus handling the display data
  channel
- port@[0-1]: Port nodes with endpoint definitions as defined in
  Documentation/devicetree/bindings/media/video-interfaces.txt.
  Port 0 is the input port connected to the IPU display interface,
  port 1 is the output port connected to a panel.

example:

display@di0 {
	compatible = "fsl,imx-parallel-display";
	edid = [edid-data];
	interface-pix-fmt = "rgb24";

	port@0 {
		reg = <0>;

		display_in: endpoint {
			remote-endpoint = <&ipu_di0_disp0>;
		};
	};

	port@1 {
		reg = <1>;

		display_out: endpoint {
			remote-endpoint = <&panel_in>;
		};
	};
};

panel {
	...

	port {
		panel_in: endpoint {
			remote-endpoint = <&display_out>;
		};
	};
};