blob: 555731a9eeceaa4d25d64629f895439a69384e2f [file] [log] [blame]
* Freescale Fast Ethernet Controller (FEC)
Required properties:
- compatible : Should be "fsl,<soc>-fec"
- reg : Address and length of the register set for the device
- interrupts : Should contain fec interrupt
- phy-mode : See ethernet.txt file in the same directory
- clock-name: Should be the names of the clocks
- "ipg" for MAC ipg_clk_s, ipg_clk_mac_s that are for register accessing
- "ahb" for MAC ipg_clk, ipg_clk_mac that are bus clock
- "ptp" for IEEE1588 timer clock
- "enet_clk_ref" for MAC transmit/receiver reference clock
- "enet_out" output clock for external device
- clocks: Phandles to input clocks.
Optional properties:
- phy-reset-gpios : Should specify the gpio for phy reset
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
- phy-reset-active-high : If present then the reset sequence using the GPIO
specified in the "phy-reset-gpios" property is reversed (H=reset state,
L=operation state).
- phy-supply : regulator that powers the Ethernet PHY.
- phy-handle : phandle to the PHY device connected to this device.
- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
Use instead of phy-handle.
- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
hw multi queues. Should specify the tx queue number, otherwise set tx queue
number to 1.
- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
hw multi queues. Should specify the rx queue number, otherwise set rx queue
number to 1.
- fsl,magic-packet : If present, indicates that the hardware supports waking
up via magic packet.
- fsl,err006687-workaround-present: If present indicates that the system has
the hardware workaround for ERR006687 applied and does not need a software
workaround.
- fsl,wakeup_irq : The property define the wakeup irq index in enet irq source.
- stop-mode : If present, indicates soc need to set gpr bit to request stop
mode.
- fsl,ar8031-phy-fixup : If present, indicates board need to do phy fixup setting.
- mii-exclusive: If present, each MAC has their exclusive MDIO bus in current board
design, otherwise mutiple MACs share one MDIO bus to reduce Pins utilize.
Optional subnodes:
- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes
according to phy.txt in the same directory
Example:
ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
local-mac-address = [00 04 9F 01 1B B9];
phy-supply = <&reg_fec_supply>;
};
Example with phy specified:
ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
local-mac-address = [00 04 9F 01 1B B9];
phy-supply = <&reg_fec_supply>;
phy-handle = <&ethphy>;
mdio {
ethphy: ethernet-phy@6 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <6>;
max-speed = <100>;
};
};
};