blob: 694987d3c17a1085ba9fce589d81cc9ee99a7717 [file] [log] [blame]
Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
This is a special case of a MDIO bus multiplexer. One or more GPIO
lines are used to control which child bus is connected.
Required properties in addition to the generic multiplexer properties:
- compatible : mdio-mux-gpio.
- gpios : GPIO specifiers for each GPIO line. One or more must be specified.
Example :
/* The parent MDIO bus. */
smi1: mdio@1180000001900 {
compatible = "cavium,octeon-3860-mdio";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x11800 0x00001900 0x0 0x40>;
};
/*
An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
pair of GPIO lines. Child busses 2 and 3 populated with 4
PHYs each.
*/
mdio-mux {
compatible = "mdio-mux-gpio";
gpios = <&gpio1 3 0>, <&gpio1 4 0>;
mdio-parent-bus = <&smi1>;
#address-cells = <1>;
#size-cells = <0>;
mdio@2 {
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
phy11: ethernet-phy@1 {
reg = <1>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy12: ethernet-phy@2 {
reg = <2>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy13: ethernet-phy@3 {
reg = <3>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
phy14: ethernet-phy@4 {
reg = <4>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
};
mdio@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
phy21: ethernet-phy@1 {
reg = <1>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy22: ethernet-phy@2 {
reg = <2>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy23: ethernet-phy@3 {
reg = <3>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
phy24: ethernet-phy@4 {
reg = <4>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
};
};