Common MDIO bus multiplexer/switch properties.

An MDIO bus multiplexer/switch will have several child busses that are
numbered uniquely in a device dependent manner.  The nodes for an MDIO
bus multiplexer/switch will have one child node for each child bus.

Required properties:
- #address-cells = <1>;
- #size-cells = <0>;

Optional properties:
- mdio-parent-bus : phandle to the parent MDIO bus.

- Other properties specific to the multiplexer/switch hardware.

Required properties for child nodes:
- #address-cells = <1>;
- #size-cells = <0>;
- reg : The sub-bus number.


Example :

	/* The parent MDIO bus. */
	smi1: mdio@1180000001900 {
		compatible = "cavium,octeon-3860-mdio";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x11800 0x00001900 0x0 0x40>;
	};

	/*
	   An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
	   pair of GPIO lines.  Child busses 2 and 3 populated with 4
	   PHYs each.
	 */
	mdio-mux {
		compatible = "mdio-mux-gpio";
		gpios = <&gpio1 3 0>, <&gpio1 4 0>;
		mdio-parent-bus = <&smi1>;
		#address-cells = <1>;
		#size-cells = <0>;

		mdio@2 {
			reg = <2>;
			#address-cells = <1>;
			#size-cells = <0>;

			phy11: ethernet-phy@1 {
				reg = <1>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <10 8>; /* Pin 10, active low */
			};
			phy12: ethernet-phy@2 {
				reg = <2>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <10 8>; /* Pin 10, active low */
			};
			phy13: ethernet-phy@3 {
				reg = <3>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <10 8>; /* Pin 10, active low */
			};
			phy14: ethernet-phy@4 {
				reg = <4>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <10 8>; /* Pin 10, active low */
			};
		};

		mdio@3 {
			reg = <3>;
			#address-cells = <1>;
			#size-cells = <0>;

			phy21: ethernet-phy@1 {
				reg = <1>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <12 8>; /* Pin 12, active low */
			};
			phy22: ethernet-phy@2 {
				reg = <2>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <12 8>; /* Pin 12, active low */
			};
			phy23: ethernet-phy@3 {
				reg = <3>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <12 8>; /* Pin 12, active low */
			};
			phy24: ethernet-phy@4 {
				reg = <4>;
				marvell,reg-init = <3 0x10 0 0x5777>,
					<3 0x11 0 0x00aa>,
					<3 0x12 0 0x4105>,
					<3 0x13 0 0x0a60>;
				interrupt-parent = <&gpio>;
				interrupts = <12 8>; /* Pin 12, active low */
			};
		};
	};