| Device-Tree bindings for LVDS Display Bridge (ldb) |
| |
| LVDS Display Bridge |
| =================== |
| |
| The LVDS Display Bridge device tree node contains up to two lvds-channel |
| nodes describing each of the two LVDS encoder channels of the bridge. |
| |
| Required properties: |
| - #address-cells : should be <1> |
| - #size-cells : should be <0> |
| - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". |
| Both LDB versions are similar, but i.MX6 has an additional |
| multiplexer in the front to select any of the four IPU display |
| interfaces as input for each LVDS channel. |
| - gpr : should be <&gpr> on i.MX53 and i.MX6q. |
| The phandle points to the iomuxc-gpr region containing the LVDS |
| control register. |
| - clocks, clock-names : phandles to the LDB divider and selector clocks and to |
| the display interface selector clocks, as described in |
| Documentation/devicetree/bindings/clock/clock-bindings.txt |
| The following clocks are expected on i.MX53: |
| "di0_pll" - LDB LVDS channel 0 mux |
| "di1_pll" - LDB LVDS channel 1 mux |
| "di0" - LDB LVDS channel 0 gate |
| "di1" - LDB LVDS channel 1 gate |
| "di0_sel" - IPU1 DI0 mux |
| "di1_sel" - IPU1 DI1 mux |
| On i.MX6q the following additional clocks are needed: |
| "di2_sel" - IPU2 DI0 mux |
| "di3_sel" - IPU2 DI1 mux |
| The needed clock numbers for each are documented in |
| Documentation/devicetree/bindings/clock/imx5-clock.txt, and in |
| Documentation/devicetree/bindings/clock/imx6q-clock.txt. |
| |
| Optional properties: |
| - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q |
| - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, |
| not used on i.MX6q |
| - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should |
| be configured - one input will be distributed on both outputs in dual |
| channel mode |
| |
| LVDS Channel |
| ============ |
| |
| Each LVDS Channel has to contain either an of graph link to a panel device node |
| or a display-timings node that describes the video timings for the connected |
| LVDS display as well as the fsl,data-mapping and fsl,data-width properties. |
| |
| Required properties: |
| - reg : should be <0> or <1> |
| - port: Input and output port nodes with endpoint definitions as defined in |
| Documentation/devicetree/bindings/graph.txt. |
| On i.MX5, the internal two-input-multiplexer is used. Due to hardware |
| limitations, only one input port (port@[0,1]) can be used for each channel |
| (lvds-channel@[0,1], respectively). |
| On i.MX6, there should be four input ports (port@[0-3]) that correspond |
| to the four LVDS multiplexer inputs. |
| A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected |
| to a panel input port. Optionally, the output port can be left out if |
| display-timings are used instead. |
| |
| Optional properties (required if display-timings are used): |
| - display-timings : A node that describes the display timings as defined in |
| Documentation/devicetree/bindings/video/display-timing.txt. |
| - fsl,data-mapping : should be "spwg" or "jeida" |
| This describes how the color bits are laid out in the |
| serialized LVDS signal. |
| - fsl,data-width : should be <18> or <24> |
| |
| example: |
| |
| gpr: iomuxc-gpr@53fa8000 { |
| /* ... */ |
| }; |
| |
| ldb: ldb@53fa8008 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx53-ldb"; |
| gpr = <&gpr>; |
| clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, |
| <&clks IMX5_CLK_LDB_DI1_SEL>, |
| <&clks IMX5_CLK_IPU_DI0_SEL>, |
| <&clks IMX5_CLK_IPU_DI1_SEL>, |
| <&clks IMX5_CLK_LDB_DI0_GATE>, |
| <&clks IMX5_CLK_LDB_DI1_GATE>; |
| clock-names = "di0_pll", "di1_pll", |
| "di0_sel", "di1_sel", |
| "di0", "di1"; |
| |
| /* Using an of-graph endpoint link to connect the panel */ |
| lvds-channel@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| lvds0_in: endpoint { |
| remote-endpoint = <&ipu_di0_lvds0>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| lvds0_out: endpoint { |
| remote-endpoint = <&panel_in>; |
| }; |
| }; |
| }; |
| |
| /* Using display-timings and fsl,data-mapping/width instead */ |
| lvds-channel@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| fsl,data-mapping = "spwg"; |
| fsl,data-width = <24>; |
| |
| display-timings { |
| /* ... */ |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| lvds1_in: endpoint { |
| remote-endpoint = <&ipu_di1_lvds1>; |
| }; |
| }; |
| }; |
| }; |
| |
| panel: lvds-panel { |
| /* ... */ |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&lvds0_out>; |
| }; |
| }; |
| }; |