u-boot-imx/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c

/*
 * arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c
 * This SPD SDRAM detection code supports AMCC PPC44x cpu's with a
 * DDR2 controller (non Denali Core). Those currently are:
 *
 * 405:		405EX(r)
 * 440/460:	440SP/440SPe/460EX/460GT
 *
 * Copyright (c) 2008 Nuovation System Designs, LLC
 *   Grant Erickson <gerickson@nuovations.com>

 * (C) Copyright 2007-2009
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 * COPYRIGHT   AMCC   CORPORATION 2004
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/* define DEBUG for debugging output (obviously ;-)) */
#if 0
#define DEBUG
#endif

#include <common.h>
#include <command.h>
#include <asm/ppc4xx.h>
#include <i2c.h>
#include <asm/io.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/cache.h>

#include "ecc.h"

#define PPC4xx_IBM_DDR2_DUMP_REGISTER(mnemonic)				\
	do {								\
		u32 data;						\
		mfsdram(SDRAM_##mnemonic, data);			\
		printf("%20s[%02x] = 0x%08X\n",				\
		       "SDRAM_" #mnemonic, SDRAM_##mnemonic, data);	\
	} while (0)

#define PPC4xx_IBM_DDR2_DUMP_MQ_REGISTER(mnemonic)			\
	do {								\
		u32 data;						\
		data = mfdcr(SDRAM_##mnemonic);				\
		printf("%20s[%02x] = 0x%08X\n",				\
		       "SDRAM_" #mnemonic, SDRAM_##mnemonic, data);	\
	} while (0)

static void update_rdcc(void)
{
	u32 val;

	/*
	 * Complete RDSS configuration as mentioned on page 7 of the AMCC
	 * PowerPC440SP/SPe DDR2 application note:
	 * "DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
	 *
	 * Or item #10 "10. Complete RDSS configuration" in chapter
	 * "22.2.9 SDRAM Initialization" of AMCC PPC460EX/EXr/GT users
	 * manual.
	 */
	mfsdram(SDRAM_RTSR, val);
	if ((val & SDRAM_RTSR_TRK1SM_MASK) == SDRAM_RTSR_TRK1SM_ATPLS1) {
		mfsdram(SDRAM_RDCC, val);
		if ((val & SDRAM_RDCC_RDSS_MASK) != SDRAM_RDCC_RDSS_T4) {
			val += 0x40000000;
			mtsdram(SDRAM_RDCC, val);
		}
	}
}

#if defined(CONFIG_440)
/*
 * This DDR2 setup code can dynamically setup the TLB entries for the DDR2
 * memory region. Right now the cache should still be disabled in U-Boot
 * because of the EMAC driver, that need its buffer descriptor to be located
 * in non cached memory.
 *
 * If at some time this restriction doesn't apply anymore, just define
 * CONFIG_4xx_DCACHE in the board config file and this code should setup
 * everything correctly.
 */
#ifdef CONFIG_4xx_DCACHE
/* enable caching on SDRAM */
#define MY_TLB_WORD2_I_ENABLE		0
#else
/* disable caching on SDRAM */
#define MY_TLB_WORD2_I_ENABLE		TLB_WORD2_I_ENABLE
#endif /* CONFIG_4xx_DCACHE */

void dcbz_area(u32 start_address, u32 num_bytes);
#endif /* CONFIG_440 */

#define MAXRANKS	4
#define MAXBXCF		4

#define MULDIV64(m1, m2, d)	(u32)(((u64)(m1) * (u64)(m2)) / (u64)(d))

/*-----------------------------------------------------------------------------+
 * sdram_memsize
 *-----------------------------------------------------------------------------*/
phys_size_t sdram_memsize(void)
{
	phys_size_t mem_size;
	unsigned long mcopt2;
	unsigned long mcstat;
	unsigned long mb0cf;
	unsigned long sdsz;
	unsigned long i;

	mem_size = 0;

	mfsdram(SDRAM_MCOPT2, mcopt2);
	mfsdram(SDRAM_MCSTAT, mcstat);

	/* DDR controller must be enabled and not in self-refresh. */
	/* Otherwise memsize is zero. */
	if (((mcopt2 & SDRAM_MCOPT2_DCEN_MASK) == SDRAM_MCOPT2_DCEN_ENABLE)
	    && ((mcopt2 & SDRAM_MCOPT2_SREN_MASK) == SDRAM_MCOPT2_SREN_EXIT)
	    && ((mcstat & (SDRAM_MCSTAT_MIC_MASK | SDRAM_MCSTAT_SRMS_MASK))
		== (SDRAM_MCSTAT_MIC_COMP | SDRAM_MCSTAT_SRMS_NOT_SF))) {
		for (i = 0; i < MAXBXCF; i++) {
			mfsdram(SDRAM_MB0CF + (i << 2), mb0cf);
			/* Banks enabled */
			if ((mb0cf & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {
#if defined(CONFIG_440)
				sdsz = mfdcr_any(SDRAM_R0BAS + i) & SDRAM_RXBAS_SDSZ_MASK;
#else
				sdsz = mb0cf & SDRAM_RXBAS_SDSZ_MASK;
#endif
				switch(sdsz) {
				case SDRAM_RXBAS_SDSZ_8:
					mem_size+=8;
					break;
				case SDRAM_RXBAS_SDSZ_16:
					mem_size+=16;
					break;
				case SDRAM_RXBAS_SDSZ_32:
					mem_size+=32;
					break;
				case SDRAM_RXBAS_SDSZ_64:
					mem_size+=64;
					break;
				case SDRAM_RXBAS_SDSZ_128:
					mem_size+=128;
					break;
				case SDRAM_RXBAS_SDSZ_256:
					mem_size+=256;
					break;
				case SDRAM_RXBAS_SDSZ_512:
					mem_size+=512;
					break;
				case SDRAM_RXBAS_SDSZ_1024:
					mem_size+=1024;
					break;
				case SDRAM_RXBAS_SDSZ_2048:
					mem_size+=2048;
					break;
				case SDRAM_RXBAS_SDSZ_4096:
					mem_size+=4096;
					break;
				default:
					printf("WARNING: Unsupported bank size (SDSZ=0x%lx)!\n"
					       , sdsz);
					mem_size=0;
					break;
				}
			}
		}
	}

	return mem_size << 20;
}

/*-----------------------------------------------------------------------------+
 * is_ecc_enabled
 *-----------------------------------------------------------------------------*/
static unsigned long is_ecc_enabled(void)
{
	unsigned long val;

	mfsdram(SDRAM_MCOPT1, val);

	return SDRAM_MCOPT1_MCHK_CHK_DECODE(val);
}

/*-----------------------------------------------------------------------------+
 * board_add_ram_info
 *-----------------------------------------------------------------------------*/
void board_add_ram_info(int use_default)
{
	PPC4xx_SYS_INFO board_cfg;
	u32 val;

	if (is_ecc_enabled())
		puts(" (ECC");
	else
		puts(" (ECC not");

	get_sys_info(&board_cfg);

#if defined(CONFIG_405EX)
	val = board_cfg.freqPLB;
#else
	mfsdr(SDR0_DDR0, val);
	val = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(val), 1);
#endif
	printf(" enabled, %d MHz", (val * 2) / 1000000);

	mfsdram(SDRAM_MMODE, val);
	val = (val & SDRAM_MMODE_DCL_MASK) >> 4;
	printf(", CL%d)", val);
}

#if defined(CONFIG_SPD_EEPROM)

/*-----------------------------------------------------------------------------+
 * Defines
 *-----------------------------------------------------------------------------*/
#define SDRAM_DDR1	1
#define SDRAM_DDR2	2
#define SDRAM_NONE	0

#define MAXDIMMS	2
#define MAX_SPD_BYTES	256   /* Max number of bytes on the DIMM's SPD EEPROM */

#define ONE_BILLION	1000000000

#define CMD_NOP		(7 << 19)
#define CMD_PRECHARGE	(2 << 19)
#define CMD_REFRESH	(1 << 19)
#define CMD_EMR		(0 << 19)
#define CMD_READ	(5 << 19)
#define CMD_WRITE	(4 << 19)

#define SELECT_MR	(0 << 16)
#define SELECT_EMR	(1 << 16)
#define SELECT_EMR2	(2 << 16)
#define SELECT_EMR3	(3 << 16)

/* MR */
#define DLL_RESET	0x00000100

#define WRITE_RECOV_2	(1 << 9)
#define WRITE_RECOV_3	(2 << 9)
#define WRITE_RECOV_4	(3 << 9)
#define WRITE_RECOV_5	(4 << 9)
#define WRITE_RECOV_6	(5 << 9)

#define BURST_LEN_4	0x00000002

/* EMR */
#define ODT_0_OHM	0x00000000
#define ODT_50_OHM	0x00000044
#define ODT_75_OHM	0x00000004
#define ODT_150_OHM	0x00000040

#define ODS_FULL	0x00000000
#define ODS_REDUCED	0x00000002
#define OCD_CALIB_DEF	0x00000380

/* defines for ODT (On Die Termination) of the 440SP(e) DDR2 controller */
#define ODT_EB0R	(0x80000000 >> 8)
#define ODT_EB0W	(0x80000000 >> 7)
#define CALC_ODT_R(n)	(ODT_EB0R << (n << 1))
#define CALC_ODT_W(n)	(ODT_EB0W << (n << 1))
#define CALC_ODT_RW(n)	(CALC_ODT_R(n) | CALC_ODT_W(n))

/* Defines for the Read Cycle Delay test */
#define NUMMEMTESTS	8
#define NUMMEMWORDS	8
#define NUMLOOPS	64		/* memory test loops */

/*
 * Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM.
 * To support such configurations, we "only" map the first 2GB via the TLB's. We
 * need some free virtual address space for the remaining peripherals like, SoC
 * devices, FLASH etc.
 *
 * Note that ECC is currently not supported on configurations with more than 2GB
 * SDRAM. This is because we only map the first 2GB on such systems, and therefore
 * the ECC parity byte of the remaining area can't be written.
 */

/*
 * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed
 */
void __spd_ddr_init_hang (void)
{
	hang ();
}
void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang")));

/*
 * To provide an interface for board specific config values in this common
 * DDR setup code, we implement he "weak" default functions here. They return
 * the default value back to the caller.
 *
 * Please see include/configs/yucca.h for an example fora board specific
 * implementation.
 */
u32 __ddr_wrdtr(u32 default_val)
{
	return default_val;
}
u32 ddr_wrdtr(u32) __attribute__((weak, alias("__ddr_wrdtr")));

u32 __ddr_clktr(u32 default_val)
{
	return default_val;
}
u32 ddr_clktr(u32) __attribute__((weak, alias("__ddr_clktr")));


/* Private Structure Definitions */

/* enum only to ease code for cas latency setting */
typedef enum ddr_cas_id {
	DDR_CAS_2      = 20,
	DDR_CAS_2_5    = 25,
	DDR_CAS_3      = 30,
	DDR_CAS_4      = 40,
	DDR_CAS_5      = 50
} ddr_cas_id_t;

/*-----------------------------------------------------------------------------+
 * Prototypes
 *-----------------------------------------------------------------------------*/
static void get_spd_info(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks);
static void check_mem_type(unsigned long *dimm_populated,
			   unsigned char *iic0_dimm_addr,
			   unsigned long num_dimm_banks);
static void check_frequency(unsigned long *dimm_populated,
			    unsigned char *iic0_dimm_addr,
			    unsigned long num_dimm_banks);
static void check_rank_number(unsigned long *dimm_populated,
			      unsigned char *iic0_dimm_addr,
			      unsigned long num_dimm_banks);
static void check_voltage_type(unsigned long *dimm_populated,
			       unsigned char *iic0_dimm_addr,
			       unsigned long num_dimm_banks);
static void program_memory_queue(unsigned long *dimm_populated,
				 unsigned char *iic0_dimm_addr,
				 unsigned long num_dimm_banks);
static void program_codt(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks);
static void program_mode(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks,
			 ddr_cas_id_t *selected_cas,
			 int *write_recovery);
static void program_tr(unsigned long *dimm_populated,
		       unsigned char *iic0_dimm_addr,
		       unsigned long num_dimm_banks);
static void program_rtr(unsigned long *dimm_populated,
			unsigned char *iic0_dimm_addr,
			unsigned long num_dimm_banks);
static void program_bxcf(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks);
static void program_copt1(unsigned long *dimm_populated,
			  unsigned char *iic0_dimm_addr,
			  unsigned long num_dimm_banks);
static void program_initplr(unsigned long *dimm_populated,
			    unsigned char *iic0_dimm_addr,
			    unsigned long num_dimm_banks,
			    ddr_cas_id_t selected_cas,
			    int write_recovery);
#ifdef CONFIG_DDR_ECC
static void program_ecc(unsigned long *dimm_populated,
			unsigned char *iic0_dimm_addr,
			unsigned long num_dimm_banks,
			unsigned long tlb_word2_i_value);
#endif
#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
static void program_DQS_calibration(unsigned long *dimm_populated,
				unsigned char *iic0_dimm_addr,
				unsigned long num_dimm_banks);
#ifdef HARD_CODED_DQS /* calibration test with hardvalues */
static void	test(void);
#else
static void	DQS_calibration_process(void);
#endif
#endif

static unsigned char spd_read(uchar chip, uint addr)
{
	unsigned char data[2];

	if (i2c_probe(chip) == 0)
		if (i2c_read(chip, addr, 1, data, 1) == 0)
			return data[0];

	return 0;
}

/*-----------------------------------------------------------------------------+
 * initdram.  Initializes the 440SP Memory Queue and DDR SDRAM controller.
 * Note: This routine runs from flash with a stack set up in the chip's
 * sram space.  It is important that the routine does not require .sbss, .bss or
 * .data sections.  It also cannot call routines that require these sections.
 *-----------------------------------------------------------------------------*/
/*-----------------------------------------------------------------------------
 * Function:	 initdram
 * Description:  Configures SDRAM memory banks for DDR operation.
 *		 Auto Memory Configuration option reads the DDR SDRAM EEPROMs
 *		 via the IIC bus and then configures the DDR SDRAM memory
 *		 banks appropriately. If Auto Memory Configuration is
 *		 not used, it is assumed that no DIMM is plugged
 *-----------------------------------------------------------------------------*/
phys_size_t initdram(int board_type)
{
	unsigned char iic0_dimm_addr[] = SPD_EEPROM_ADDRESS;
	unsigned long dimm_populated[MAXDIMMS] = {SDRAM_NONE, SDRAM_NONE};
	unsigned long num_dimm_banks;		/* on board dimm banks */
	unsigned long val;
	ddr_cas_id_t selected_cas = DDR_CAS_5;	/* preset to silence compiler */
	int write_recovery;
	phys_size_t dram_size = 0;

	if (IS_ENABLED(CONFIG_SYS_RAMBOOT)) {
		/*
		 * Reduce RAM size to avoid overwriting memory used by
		 * current stack? Not sure what is happening.
		 */
		return sdram_memsize() / 2;
	}

	num_dimm_banks = sizeof(iic0_dimm_addr);

	/*------------------------------------------------------------------
	 * Reset the DDR-SDRAM controller.
	 *-----------------------------------------------------------------*/
	mtsdr(SDR0_SRST, SDR0_SRST0_DMC);
	mtsdr(SDR0_SRST, 0x00000000);

	/*
	 * Make sure I2C controller is initialized
	 * before continuing.
	 */

	/* switch to correct I2C bus */
	i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM);

	/*------------------------------------------------------------------
	 * Clear out the serial presence detect buffers.
	 * Perform IIC reads from the dimm.  Fill in the spds.
	 * Check to see if the dimm slots are populated
	 *-----------------------------------------------------------------*/
	get_spd_info(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Check the memory type for the dimms plugged.
	 *-----------------------------------------------------------------*/
	check_mem_type(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Check the frequency supported for the dimms plugged.
	 *-----------------------------------------------------------------*/
	check_frequency(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Check the total rank number.
	 *-----------------------------------------------------------------*/
	check_rank_number(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Check the voltage type for the dimms plugged.
	 *-----------------------------------------------------------------*/
	check_voltage_type(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Program SDRAM controller options 2 register
	 * Except Enabling of the memory controller.
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_MCOPT2, val);
	mtsdram(SDRAM_MCOPT2,
		(val &
		 ~(SDRAM_MCOPT2_SREN_MASK | SDRAM_MCOPT2_PMEN_MASK |
		   SDRAM_MCOPT2_IPTR_MASK | SDRAM_MCOPT2_XSRP_MASK |
		   SDRAM_MCOPT2_ISIE_MASK))
		| (SDRAM_MCOPT2_SREN_ENTER | SDRAM_MCOPT2_PMEN_DISABLE |
		   SDRAM_MCOPT2_IPTR_IDLE | SDRAM_MCOPT2_XSRP_ALLOW |
		   SDRAM_MCOPT2_ISIE_ENABLE));

	/*------------------------------------------------------------------
	 * Program SDRAM controller options 1 register
	 * Note: Does not enable the memory controller.
	 *-----------------------------------------------------------------*/
	program_copt1(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Set the SDRAM Controller On Die Termination Register
	 *-----------------------------------------------------------------*/
	program_codt(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Program SDRAM refresh register.
	 *-----------------------------------------------------------------*/
	program_rtr(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Program SDRAM mode register.
	 *-----------------------------------------------------------------*/
	program_mode(dimm_populated, iic0_dimm_addr, num_dimm_banks,
		     &selected_cas, &write_recovery);

	/*------------------------------------------------------------------
	 * Set the SDRAM Write Data/DM/DQS Clock Timing Reg
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_WRDTR, val);
	mtsdram(SDRAM_WRDTR, (val & ~(SDRAM_WRDTR_LLWP_MASK | SDRAM_WRDTR_WTR_MASK)) |
		ddr_wrdtr(SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_90_DEG_ADV));

	/*------------------------------------------------------------------
	 * Set the SDRAM Clock Timing Register
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_CLKTR, val);
	mtsdram(SDRAM_CLKTR, (val & ~SDRAM_CLKTR_CLKP_MASK) |
		ddr_clktr(SDRAM_CLKTR_CLKP_0_DEG));

	/*------------------------------------------------------------------
	 * Program the BxCF registers.
	 *-----------------------------------------------------------------*/
	program_bxcf(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Program SDRAM timing registers.
	 *-----------------------------------------------------------------*/
	program_tr(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Set the Extended Mode register
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_MEMODE, val);
	mtsdram(SDRAM_MEMODE,
		(val & ~(SDRAM_MEMODE_DIC_MASK  | SDRAM_MEMODE_DLL_MASK |
			 SDRAM_MEMODE_RTT_MASK | SDRAM_MEMODE_DQS_MASK)) |
		(SDRAM_MEMODE_DIC_NORMAL | SDRAM_MEMODE_DLL_ENABLE
		 | SDRAM_MEMODE_RTT_150OHM | SDRAM_MEMODE_DQS_ENABLE));

	/*------------------------------------------------------------------
	 * Program Initialization preload registers.
	 *-----------------------------------------------------------------*/
	program_initplr(dimm_populated, iic0_dimm_addr, num_dimm_banks,
			selected_cas, write_recovery);

	/*------------------------------------------------------------------
	 * Delay to ensure 200usec have elapsed since reset.
	 *-----------------------------------------------------------------*/
	udelay(400);

	/*------------------------------------------------------------------
	 * Set the memory queue core base addr.
	 *-----------------------------------------------------------------*/
	program_memory_queue(dimm_populated, iic0_dimm_addr, num_dimm_banks);

	/*------------------------------------------------------------------
	 * Program SDRAM controller options 2 register
	 * Enable the memory controller.
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_MCOPT2, val);
	mtsdram(SDRAM_MCOPT2,
		(val & ~(SDRAM_MCOPT2_SREN_MASK | SDRAM_MCOPT2_DCEN_MASK |
			 SDRAM_MCOPT2_IPTR_MASK | SDRAM_MCOPT2_ISIE_MASK)) |
			 SDRAM_MCOPT2_IPTR_EXECUTE);

	/*------------------------------------------------------------------
	 * Wait for IPTR_EXECUTE init sequence to complete.
	 *-----------------------------------------------------------------*/
	do {
		mfsdram(SDRAM_MCSTAT, val);
	} while ((val & SDRAM_MCSTAT_MIC_MASK) == SDRAM_MCSTAT_MIC_NOTCOMP);

	/* enable the controller only after init sequence completes */
	mfsdram(SDRAM_MCOPT2, val);
	mtsdram(SDRAM_MCOPT2, (val | SDRAM_MCOPT2_DCEN_ENABLE));

	/* Make sure delay-line calibration is done before proceeding */
	do {
		mfsdram(SDRAM_DLCR, val);
	} while (!(val & SDRAM_DLCR_DLCS_COMPLETE));

	/* get installed memory size */
	dram_size = sdram_memsize();

	/*
	 * Limit size to 2GB
	 */
	if (dram_size > CONFIG_MAX_MEM_MAPPED)
		dram_size = CONFIG_MAX_MEM_MAPPED;

	/* and program tlb entries for this size (dynamic) */

	/*
	 * Program TLB entries with caches enabled, for best performace
	 * while auto-calibrating and ECC generation
	 */
	program_tlb(0, 0, dram_size, 0);

	/*------------------------------------------------------------------
	 * DQS calibration.
	 *-----------------------------------------------------------------*/
#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
	DQS_autocalibration();
#else
	program_DQS_calibration(dimm_populated, iic0_dimm_addr, num_dimm_banks);
#endif
	/*
	 * Now complete RDSS configuration as mentioned on page 7 of the AMCC
	 * PowerPC440SP/SPe DDR2 application note:
	 * "DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
	 */
	update_rdcc();

#ifdef CONFIG_DDR_ECC
	/*------------------------------------------------------------------
	 * If ecc is enabled, initialize the parity bits.
	 *-----------------------------------------------------------------*/
	program_ecc(dimm_populated, iic0_dimm_addr, num_dimm_banks, 0);
#endif

	/*
	 * Flush the dcache before removing the TLB with caches
	 * enabled. Otherwise this might lead to problems later on,
	 * e.g. while booting Linux (as seen on ICON-440SPe).
	 */
	flush_dcache();

	/*
	 * Now after initialization (auto-calibration and ECC generation)
	 * remove the TLB entries with caches enabled and program again with
	 * desired cache functionality
	 */
	remove_tlb(0, dram_size);
	program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE);

	ppc4xx_ibm_ddr2_register_dump();

	/*
	 * Clear potential errors resulting from auto-calibration.
	 * If not done, then we could get an interrupt later on when
	 * exceptions are enabled.
	 */
	set_mcsr(get_mcsr());

	return sdram_memsize();
}

static void get_spd_info(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long dimm_found;
	unsigned char num_of_bytes;
	unsigned char total_size;

	dimm_found = false;
	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		num_of_bytes = 0;
		total_size = 0;

		num_of_bytes = spd_read(iic0_dimm_addr[dimm_num], 0);
		debug("\nspd_read(0x%x) returned %d\n",
		      iic0_dimm_addr[dimm_num], num_of_bytes);
		total_size = spd_read(iic0_dimm_addr[dimm_num], 1);
		debug("spd_read(0x%x) returned %d\n",
		      iic0_dimm_addr[dimm_num], total_size);

		if ((num_of_bytes != 0) && (total_size != 0)) {
			dimm_populated[dimm_num] = true;
			dimm_found = true;
			debug("DIMM slot %lu: populated\n", dimm_num);
		} else {
			dimm_populated[dimm_num] = false;
			debug("DIMM slot %lu: Not populated\n", dimm_num);
		}
	}

	if (dimm_found == false) {
		printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n");
		spd_ddr_init_hang ();
	}
}


/*------------------------------------------------------------------
 * For the memory DIMMs installed, this routine verifies that they
 * really are DDR specific DIMMs.
 *-----------------------------------------------------------------*/
static void check_mem_type(unsigned long *dimm_populated,
			   unsigned char *iic0_dimm_addr,
			   unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long dimm_type;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] == true) {
			dimm_type = spd_read(iic0_dimm_addr[dimm_num], 2);
			switch (dimm_type) {
			case 1:
				printf("ERROR: Standard Fast Page Mode DRAM DIMM detected in "
				       "slot %d.\n", (unsigned int)dimm_num);
				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			case 2:
				printf("ERROR: EDO DIMM detected in slot %d.\n",
				       (unsigned int)dimm_num);
				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			case 3:
				printf("ERROR: Pipelined Nibble DIMM detected in slot %d.\n",
				       (unsigned int)dimm_num);
				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			case 4:
				printf("ERROR: SDRAM DIMM detected in slot %d.\n",
				       (unsigned int)dimm_num);
				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			case 5:
				printf("ERROR: Multiplexed ROM DIMM detected in slot %d.\n",
				       (unsigned int)dimm_num);
				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			case 6:
				printf("ERROR: SGRAM DIMM detected in slot %d.\n",
				       (unsigned int)dimm_num);
				printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			case 7:
				debug("DIMM slot %lu: DDR1 SDRAM detected\n", dimm_num);
				dimm_populated[dimm_num] = SDRAM_DDR1;
				break;
			case 8:
				debug("DIMM slot %lu: DDR2 SDRAM detected\n", dimm_num);
				dimm_populated[dimm_num] = SDRAM_DDR2;
				break;
			default:
				printf("ERROR: Unknown DIMM detected in slot %d.\n",
				       (unsigned int)dimm_num);
				printf("Only DDR1 and DDR2 SDRAM DIMMs are supported.\n");
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			}
		}
	}
	for (dimm_num = 1; dimm_num < num_dimm_banks; dimm_num++) {
		if ((dimm_populated[dimm_num-1] != SDRAM_NONE)
		    && (dimm_populated[dimm_num]   != SDRAM_NONE)
		    && (dimm_populated[dimm_num-1] != dimm_populated[dimm_num])) {
			printf("ERROR: DIMM's DDR1 and DDR2 type can not be mixed.\n");
			spd_ddr_init_hang ();
		}
	}
}

/*------------------------------------------------------------------
 * For the memory DIMMs installed, this routine verifies that
 * frequency previously calculated is supported.
 *-----------------------------------------------------------------*/
static void check_frequency(unsigned long *dimm_populated,
			    unsigned char *iic0_dimm_addr,
			    unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long tcyc_reg;
	unsigned long cycle_time;
	unsigned long calc_cycle_time;
	unsigned long sdram_freq;
	unsigned long sdr_ddrpll;
	PPC4xx_SYS_INFO board_cfg;

	/*------------------------------------------------------------------
	 * Get the board configuration info.
	 *-----------------------------------------------------------------*/
	get_sys_info(&board_cfg);

	mfsdr(SDR0_DDR0, sdr_ddrpll);
	sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));

	/*
	 * calc_cycle_time is calculated from DDR frequency set by board/chip
	 * and is expressed in multiple of 10 picoseconds
	 * to match the way DIMM cycle time is calculated below.
	 */
	calc_cycle_time = MULDIV64(ONE_BILLION, 100, sdram_freq);

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 9);
			/*
			 * Byte 9, Cycle time for CAS Latency=X, is split into two nibbles:
			 * the higher order nibble (bits 4-7) designates the cycle time
			 * to a granularity of 1ns;
			 * the value presented by the lower order nibble (bits 0-3)
			 * has a granularity of .1ns and is added to the value designated
			 * by the higher nibble. In addition, four lines of the lower order
			 * nibble are assigned to support +.25,+.33, +.66 and +.75.
			 */
			 /* Convert from hex to decimal */
			if ((tcyc_reg & 0x0F) == 0x0D)
				cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
			else if ((tcyc_reg & 0x0F) == 0x0C)
				cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) + 66;
			else if ((tcyc_reg & 0x0F) == 0x0B)
				cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) + 33;
			else if ((tcyc_reg & 0x0F) == 0x0A)
				cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) + 25;
			else
				cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) +
					((tcyc_reg & 0x0F)*10);
			debug("cycle_time=%lu [10 picoseconds]\n", cycle_time);

			if  (cycle_time > (calc_cycle_time + 10)) {
				/*
				 * the provided sdram cycle_time is too small
				 * for the available DIMM cycle_time.
				 * The additionnal 100ps is here to accept a small incertainty.
				 */
				printf("ERROR: DRAM DIMM detected with cycle_time %d ps in "
				       "slot %d \n while calculated cycle time is %d ps.\n",
				       (unsigned int)(cycle_time*10),
				       (unsigned int)dimm_num,
				       (unsigned int)(calc_cycle_time*10));
				printf("Replace the DIMM, or change DDR frequency via "
				       "strapping bits.\n\n");
				spd_ddr_init_hang ();
			}
		}
	}
}

/*------------------------------------------------------------------
 * For the memory DIMMs installed, this routine verifies two
 * ranks/banks maximum are availables.
 *-----------------------------------------------------------------*/
static void check_rank_number(unsigned long *dimm_populated,
			      unsigned char *iic0_dimm_addr,
			      unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long dimm_rank;
	unsigned long total_rank = 0;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			dimm_rank = spd_read(iic0_dimm_addr[dimm_num], 5);
			if (((unsigned long)spd_read(iic0_dimm_addr[dimm_num], 2)) == 0x08)
				dimm_rank = (dimm_rank & 0x0F) +1;
			else
				dimm_rank = dimm_rank & 0x0F;


			if (dimm_rank > MAXRANKS) {
				printf("ERROR: DRAM DIMM detected with %lu ranks in "
				       "slot %lu is not supported.\n", dimm_rank, dimm_num);
				printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
			} else
				total_rank += dimm_rank;
		}
		if (total_rank > MAXRANKS) {
			printf("ERROR: DRAM DIMM detected with a total of %d ranks "
			       "for all slots.\n", (unsigned int)total_rank);
			printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
			printf("Remove one of the DIMM modules.\n\n");
			spd_ddr_init_hang ();
		}
	}
}

/*------------------------------------------------------------------
 * only support 2.5V modules.
 * This routine verifies this.
 *-----------------------------------------------------------------*/
static void check_voltage_type(unsigned long *dimm_populated,
			       unsigned char *iic0_dimm_addr,
			       unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long voltage_type;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			voltage_type = spd_read(iic0_dimm_addr[dimm_num], 8);
			switch (voltage_type) {
			case 0x00:
				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
				printf("This DIMM is 5.0 Volt/TTL.\n");
				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
				       (unsigned int)dimm_num);
				spd_ddr_init_hang ();
				break;
			case 0x01:
				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
				printf("This DIMM is LVTTL.\n");
				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
				       (unsigned int)dimm_num);
				spd_ddr_init_hang ();
				break;
			case 0x02:
				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
				printf("This DIMM is 1.5 Volt.\n");
				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
				       (unsigned int)dimm_num);
				spd_ddr_init_hang ();
				break;
			case 0x03:
				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
				printf("This DIMM is 3.3 Volt/TTL.\n");
				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
				       (unsigned int)dimm_num);
				spd_ddr_init_hang ();
				break;
			case 0x04:
				/* 2.5 Voltage only for DDR1 */
				break;
			case 0x05:
				/* 1.8 Voltage only for DDR2 */
				break;
			default:
				printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
				printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
				       (unsigned int)dimm_num);
				spd_ddr_init_hang ();
				break;
			}
		}
	}
}

/*-----------------------------------------------------------------------------+
 * program_copt1.
 *-----------------------------------------------------------------------------*/
static void program_copt1(unsigned long *dimm_populated,
			  unsigned char *iic0_dimm_addr,
			  unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long mcopt1;
	unsigned long ecc_enabled;
	unsigned long ecc = 0;
	unsigned long data_width = 0;
	unsigned long dimm_32bit;
	unsigned long dimm_64bit;
	unsigned long registered = 0;
	unsigned long attribute = 0;
	unsigned long buf0, buf1; /* TODO: code to be changed for IOP1.6 to support 4 DIMMs */
	unsigned long bankcount;
	unsigned long val;

#ifdef CONFIG_DDR_ECC
	ecc_enabled = true;
#else
	ecc_enabled = false;
#endif
	dimm_32bit = false;
	dimm_64bit = false;
	buf0 = false;
	buf1 = false;

	/*------------------------------------------------------------------
	 * Set memory controller options reg 1, SDRAM_MCOPT1.
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_MCOPT1, val);
	mcopt1 = val & ~(SDRAM_MCOPT1_MCHK_MASK | SDRAM_MCOPT1_RDEN_MASK |
			 SDRAM_MCOPT1_PMU_MASK  | SDRAM_MCOPT1_DMWD_MASK |
			 SDRAM_MCOPT1_UIOS_MASK | SDRAM_MCOPT1_BCNT_MASK |
			 SDRAM_MCOPT1_DDR_TYPE_MASK | SDRAM_MCOPT1_RWOO_MASK |
			 SDRAM_MCOPT1_WOOO_MASK | SDRAM_MCOPT1_DCOO_MASK |
			 SDRAM_MCOPT1_DREF_MASK);

	mcopt1 |= SDRAM_MCOPT1_QDEP;
	mcopt1 |= SDRAM_MCOPT1_PMU_OPEN;
	mcopt1 |= SDRAM_MCOPT1_RWOO_DISABLED;
	mcopt1 |= SDRAM_MCOPT1_WOOO_DISABLED;
	mcopt1 |= SDRAM_MCOPT1_DCOO_DISABLED;
	mcopt1 |= SDRAM_MCOPT1_DREF_NORMAL;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			/* test ecc support */
			ecc = (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 11);
			if (ecc != 0x02) /* ecc not supported */
				ecc_enabled = false;

			/* test bank count */
			bankcount = (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 17);
			if (bankcount == 0x04) /* bank count = 4 */
				mcopt1 |= SDRAM_MCOPT1_4_BANKS;
			else /* bank count = 8 */
				mcopt1 |= SDRAM_MCOPT1_8_BANKS;

			/* test for buffered/unbuffered, registered, differential clocks */
			registered = (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 20);
			attribute = (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 21);

			/* TODO: code to be changed for IOP1.6 to support 4 DIMMs */
			if (dimm_num == 0) {
				if (dimm_populated[dimm_num] == SDRAM_DDR1) /* DDR1 type */
					mcopt1 |= SDRAM_MCOPT1_DDR1_TYPE;
				if (dimm_populated[dimm_num] == SDRAM_DDR2) /* DDR2 type */
					mcopt1 |= SDRAM_MCOPT1_DDR2_TYPE;
				if (registered == 1) { /* DDR2 always buffered */
					/* TODO: what about above  comments ? */
					mcopt1 |= SDRAM_MCOPT1_RDEN;
					buf0 = true;
				} else {
					/* TODO: the mask 0x02 doesn't match Samsung def for byte 21. */
					if ((attribute & 0x02) == 0x00) {
						/* buffered not supported */
						buf0 = false;
					} else {
						mcopt1 |= SDRAM_MCOPT1_RDEN;
						buf0 = true;
					}
				}
			}
			else if (dimm_num == 1) {
				if (dimm_populated[dimm_num] == SDRAM_DDR1) /* DDR1 type */
					mcopt1 |= SDRAM_MCOPT1_DDR1_TYPE;
				if (dimm_populated[dimm_num] == SDRAM_DDR2) /* DDR2 type */
					mcopt1 |= SDRAM_MCOPT1_DDR2_TYPE;
				if (registered == 1) {
					/* DDR2 always buffered */
					mcopt1 |= SDRAM_MCOPT1_RDEN;
					buf1 = true;
				} else {
					if ((attribute & 0x02) == 0x00) {
						/* buffered not supported */
						buf1 = false;
					} else {
						mcopt1 |= SDRAM_MCOPT1_RDEN;
						buf1 = true;
					}
				}
			}

			/* Note that for DDR2 the byte 7 is reserved, but OK to keep code as is. */
			data_width = (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 6) +
				(((unsigned long)spd_read(iic0_dimm_addr[dimm_num], 7)) << 8);

			switch (data_width) {
			case 72:
			case 64:
				dimm_64bit = true;
				break;
			case 40:
			case 32:
				dimm_32bit = true;
				break;
			default:
				printf("WARNING: Detected a DIMM with a data width of %lu bits.\n",
				       data_width);
				printf("Only DIMMs with 32 or 64 bit DDR-SDRAM widths are supported.\n");
				break;
			}
		}
	}

	/* verify matching properties */
	if ((dimm_populated[0] != SDRAM_NONE) && (dimm_populated[1] != SDRAM_NONE)) {
		if (buf0 != buf1) {
			printf("ERROR: DIMM's buffered/unbuffered, registered, clocking don't match.\n");
			spd_ddr_init_hang ();
		}
	}

	if ((dimm_64bit == true) && (dimm_32bit == true)) {
		printf("ERROR: Cannot mix 32 bit and 64 bit DDR-SDRAM DIMMs together.\n");
		spd_ddr_init_hang ();
	} else if ((dimm_64bit == true) && (dimm_32bit == false)) {
		mcopt1 |= SDRAM_MCOPT1_DMWD_64;
	} else if ((dimm_64bit == false) && (dimm_32bit == true)) {
		mcopt1 |= SDRAM_MCOPT1_DMWD_32;
	} else {
		printf("ERROR: Please install only 32 or 64 bit DDR-SDRAM DIMMs.\n\n");
		spd_ddr_init_hang ();
	}

	if (ecc_enabled == true)
		mcopt1 |= SDRAM_MCOPT1_MCHK_GEN;
	else
		mcopt1 |= SDRAM_MCOPT1_MCHK_NON;

	mtsdram(SDRAM_MCOPT1, mcopt1);
}

/*-----------------------------------------------------------------------------+
 * program_codt.
 *-----------------------------------------------------------------------------*/
static void program_codt(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks)
{
	unsigned long codt;
	unsigned long modt0 = 0;
	unsigned long modt1 = 0;
	unsigned long modt2 = 0;
	unsigned long modt3 = 0;
	unsigned char dimm_num;
	unsigned char dimm_rank;
	unsigned char total_rank = 0;
	unsigned char total_dimm = 0;
	unsigned char dimm_type = 0;
	unsigned char firstSlot = 0;

	/*------------------------------------------------------------------
	 * Set the SDRAM Controller On Die Termination Register
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_CODT, codt);
	codt &= ~(SDRAM_CODT_DQS_SINGLE_END | SDRAM_CODT_CKSE_SINGLE_END);
	codt |= SDRAM_CODT_IO_NMODE;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			dimm_rank = (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 5);
			if (((unsigned long)spd_read(iic0_dimm_addr[dimm_num], 2)) == 0x08) {
				dimm_rank = (dimm_rank & 0x0F) + 1;
				dimm_type = SDRAM_DDR2;
			} else {
				dimm_rank = dimm_rank & 0x0F;
				dimm_type = SDRAM_DDR1;
			}

			total_rank += dimm_rank;
			total_dimm++;
			if ((dimm_num == 0) && (total_dimm == 1))
				firstSlot = true;
			else
				firstSlot = false;
		}
	}
	if (dimm_type == SDRAM_DDR2) {
		codt |= SDRAM_CODT_DQS_1_8_V_DDR2;
		if ((total_dimm == 1) && (firstSlot == true)) {
			if (total_rank == 1) {	/* PUUU */
				codt |= CALC_ODT_R(0);
				modt0 = CALC_ODT_W(0);
				modt1 = 0x00000000;
				modt2 = 0x00000000;
				modt3 = 0x00000000;
			}
			if (total_rank == 2) {	/* PPUU */
				codt |= CALC_ODT_R(0) | CALC_ODT_R(1);
				modt0 = CALC_ODT_W(0) | CALC_ODT_W(1);
				modt1 = 0x00000000;
				modt2 = 0x00000000;
				modt3 = 0x00000000;
			}
		} else if ((total_dimm == 1) && (firstSlot != true)) {
			if (total_rank == 1) {	/* UUPU */
				codt |= CALC_ODT_R(2);
				modt0 = 0x00000000;
				modt1 = 0x00000000;
				modt2 = CALC_ODT_W(2);
				modt3 = 0x00000000;
			}
			if (total_rank == 2) {	/* UUPP */
				codt |= CALC_ODT_R(2) | CALC_ODT_R(3);
				modt0 = 0x00000000;
				modt1 = 0x00000000;
				modt2 = CALC_ODT_W(2) | CALC_ODT_W(3);
				modt3 = 0x00000000;
			}
		}
		if (total_dimm == 2) {
			if (total_rank == 2) {	/* PUPU */
				codt |= CALC_ODT_R(0) | CALC_ODT_R(2);
				modt0 = CALC_ODT_RW(2);
				modt1 = 0x00000000;
				modt2 = CALC_ODT_RW(0);
				modt3 = 0x00000000;
			}
			if (total_rank == 4) {	/* PPPP */
				codt |= CALC_ODT_R(0) | CALC_ODT_R(1) |
					CALC_ODT_R(2) | CALC_ODT_R(3);
				modt0 = CALC_ODT_RW(2) | CALC_ODT_RW(3);
				modt1 = 0x00000000;
				modt2 = CALC_ODT_RW(0) | CALC_ODT_RW(1);
				modt3 = 0x00000000;
			}
		}
	} else {
		codt |= SDRAM_CODT_DQS_2_5_V_DDR1;
		modt0 = 0x00000000;
		modt1 = 0x00000000;
		modt2 = 0x00000000;
		modt3 = 0x00000000;

		if (total_dimm == 1) {
			if (total_rank == 1)
				codt |= 0x00800000;
			if (total_rank == 2)
				codt |= 0x02800000;
		}
		if (total_dimm == 2) {
			if (total_rank == 2)
				codt |= 0x08800000;
			if (total_rank == 4)
				codt |= 0x2a800000;
		}
	}

	debug("nb of dimm %d\n", total_dimm);
	debug("nb of rank %d\n", total_rank);
	if (total_dimm == 1)
		debug("dimm in slot %d\n", firstSlot);

	mtsdram(SDRAM_CODT, codt);
	mtsdram(SDRAM_MODT0, modt0);
	mtsdram(SDRAM_MODT1, modt1);
	mtsdram(SDRAM_MODT2, modt2);
	mtsdram(SDRAM_MODT3, modt3);
}

/*-----------------------------------------------------------------------------+
 * program_initplr.
 *-----------------------------------------------------------------------------*/
static void program_initplr(unsigned long *dimm_populated,
			    unsigned char *iic0_dimm_addr,
			    unsigned long num_dimm_banks,
			    ddr_cas_id_t selected_cas,
			    int write_recovery)
{
	u32 cas = 0;
	u32 odt = 0;
	u32 ods = 0;
	u32 mr;
	u32 wr;
	u32 emr;
	u32 emr2;
	u32 emr3;
	int dimm_num;
	int total_dimm = 0;

	/******************************************************
	 ** Assumption: if more than one DIMM, all DIMMs are the same
	 **		as already checked in check_memory_type
	 ******************************************************/

	if ((dimm_populated[0] == SDRAM_DDR1) || (dimm_populated[1] == SDRAM_DDR1)) {
		mtsdram(SDRAM_INITPLR0, 0x81B80000);
		mtsdram(SDRAM_INITPLR1, 0x81900400);
		mtsdram(SDRAM_INITPLR2, 0x81810000);
		mtsdram(SDRAM_INITPLR3, 0xff800162);
		mtsdram(SDRAM_INITPLR4, 0x81900400);
		mtsdram(SDRAM_INITPLR5, 0x86080000);
		mtsdram(SDRAM_INITPLR6, 0x86080000);
		mtsdram(SDRAM_INITPLR7, 0x81000062);
	} else if ((dimm_populated[0] == SDRAM_DDR2) || (dimm_populated[1] == SDRAM_DDR2)) {
		switch (selected_cas) {
		case DDR_CAS_3:
			cas = 3 << 4;
			break;
		case DDR_CAS_4:
			cas = 4 << 4;
			break;
		case DDR_CAS_5:
			cas = 5 << 4;
			break;
		default:
			printf("ERROR: ucode error on selected_cas value %d", selected_cas);
			spd_ddr_init_hang ();
			break;
		}

#if 0
		/*
		 * ToDo - Still a problem with the write recovery:
		 * On the Corsair CM2X512-5400C4 module, setting write recovery
		 * in the INITPLR reg to the value calculated in program_mode()
		 * results in not correctly working DDR2 memory (crash after
		 * relocation).
		 *
		 * So for now, set the write recovery to 3. This seems to work
		 * on the Corair module too.
		 *
		 * 2007-03-01, sr
		 */
		switch (write_recovery) {
		case 3:
			wr = WRITE_RECOV_3;
			break;
		case 4:
			wr = WRITE_RECOV_4;
			break;
		case 5:
			wr = WRITE_RECOV_5;
			break;
		case 6:
			wr = WRITE_RECOV_6;
			break;
		default:
			printf("ERROR: write recovery not support (%d)", write_recovery);
			spd_ddr_init_hang ();
			break;
		}
#else
		wr = WRITE_RECOV_3; /* test-only, see description above */
#endif

		for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++)
			if (dimm_populated[dimm_num] != SDRAM_NONE)
				total_dimm++;
		if (total_dimm == 1) {
			odt = ODT_150_OHM;
			ods = ODS_FULL;
		} else if (total_dimm == 2) {
			odt = ODT_75_OHM;
			ods = ODS_REDUCED;
		} else {
			printf("ERROR: Unsupported number of DIMM's (%d)", total_dimm);
			spd_ddr_init_hang ();
		}

		mr = CMD_EMR | SELECT_MR | BURST_LEN_4 | wr | cas;
		emr = CMD_EMR | SELECT_EMR | odt | ods;
		emr2 = CMD_EMR | SELECT_EMR2;
		emr3 = CMD_EMR | SELECT_EMR3;
		/* NOP - Wait 106 MemClk cycles */
		mtsdram(SDRAM_INITPLR0, SDRAM_INITPLR_ENABLE | CMD_NOP |
					SDRAM_INITPLR_IMWT_ENCODE(106));
		udelay(1000);
		/* precharge 4 MemClk cycles */
		mtsdram(SDRAM_INITPLR1, SDRAM_INITPLR_ENABLE | CMD_PRECHARGE |
					SDRAM_INITPLR_IMWT_ENCODE(4));
		/* EMR2 - Wait tMRD (2 MemClk cycles) */
		mtsdram(SDRAM_INITPLR2, SDRAM_INITPLR_ENABLE | emr2 |
					SDRAM_INITPLR_IMWT_ENCODE(2));
		/* EMR3 - Wait tMRD (2 MemClk cycles) */
		mtsdram(SDRAM_INITPLR3, SDRAM_INITPLR_ENABLE | emr3 |
					SDRAM_INITPLR_IMWT_ENCODE(2));
		/* EMR DLL ENABLE - Wait tMRD (2 MemClk cycles) */
		mtsdram(SDRAM_INITPLR4, SDRAM_INITPLR_ENABLE | emr |
					SDRAM_INITPLR_IMWT_ENCODE(2));
		/* MR w/ DLL reset - 200 cycle wait for DLL reset */
		mtsdram(SDRAM_INITPLR5, SDRAM_INITPLR_ENABLE | mr | DLL_RESET |
					SDRAM_INITPLR_IMWT_ENCODE(200));
		udelay(1000);
		/* precharge 4 MemClk cycles */
		mtsdram(SDRAM_INITPLR6, SDRAM_INITPLR_ENABLE | CMD_PRECHARGE |
					SDRAM_INITPLR_IMWT_ENCODE(4));
		/* Refresh 25 MemClk cycles */
		mtsdram(SDRAM_INITPLR7, SDRAM_INITPLR_ENABLE | CMD_REFRESH |
					SDRAM_INITPLR_IMWT_ENCODE(25));
		/* Refresh 25 MemClk cycles */
		mtsdram(SDRAM_INITPLR8, SDRAM_INITPLR_ENABLE | CMD_REFRESH |
					SDRAM_INITPLR_IMWT_ENCODE(25));
		/* Refresh 25 MemClk cycles */
		mtsdram(SDRAM_INITPLR9, SDRAM_INITPLR_ENABLE | CMD_REFRESH |
					SDRAM_INITPLR_IMWT_ENCODE(25));
		/* Refresh 25 MemClk cycles */
		mtsdram(SDRAM_INITPLR10, SDRAM_INITPLR_ENABLE | CMD_REFRESH |
					 SDRAM_INITPLR_IMWT_ENCODE(25));
		/* MR w/o DLL reset - Wait tMRD (2 MemClk cycles) */
		mtsdram(SDRAM_INITPLR11, SDRAM_INITPLR_ENABLE | mr |
					 SDRAM_INITPLR_IMWT_ENCODE(2));
		/* EMR OCD Default - Wait tMRD (2 MemClk cycles) */
		mtsdram(SDRAM_INITPLR12, SDRAM_INITPLR_ENABLE | OCD_CALIB_DEF |
					 SDRAM_INITPLR_IMWT_ENCODE(2) | emr);
		/* EMR OCD Exit */
		mtsdram(SDRAM_INITPLR13, SDRAM_INITPLR_ENABLE | emr |
					 SDRAM_INITPLR_IMWT_ENCODE(2));
	} else {
		printf("ERROR: ucode error as unknown DDR type in program_initplr");
		spd_ddr_init_hang ();
	}
}

/*------------------------------------------------------------------
 * This routine programs the SDRAM_MMODE register.
 * the selected_cas is an output parameter, that will be passed
 * by caller to call the above program_initplr( )
 *-----------------------------------------------------------------*/
static void program_mode(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks,
			 ddr_cas_id_t *selected_cas,
			 int *write_recovery)
{
	unsigned long dimm_num;
	unsigned long sdram_ddr1;
	unsigned long t_wr_ns;
	unsigned long t_wr_clk;
	unsigned long cas_bit;
	unsigned long cas_index;
	unsigned long sdram_freq;
	unsigned long ddr_check;
	unsigned long mmode;
	unsigned long tcyc_reg;
	unsigned long cycle_2_0_clk;
	unsigned long cycle_2_5_clk;
	unsigned long cycle_3_0_clk;
	unsigned long cycle_4_0_clk;
	unsigned long cycle_5_0_clk;
	unsigned long max_2_0_tcyc_ns_x_100;
	unsigned long max_2_5_tcyc_ns_x_100;
	unsigned long max_3_0_tcyc_ns_x_100;
	unsigned long max_4_0_tcyc_ns_x_100;
	unsigned long max_5_0_tcyc_ns_x_100;
	unsigned long cycle_time_ns_x_100[3];
	PPC4xx_SYS_INFO board_cfg;
	unsigned char cas_2_0_available;
	unsigned char cas_2_5_available;
	unsigned char cas_3_0_available;
	unsigned char cas_4_0_available;
	unsigned char cas_5_0_available;
	unsigned long sdr_ddrpll;

	/*------------------------------------------------------------------
	 * Get the board configuration info.
	 *-----------------------------------------------------------------*/
	get_sys_info(&board_cfg);

	mfsdr(SDR0_DDR0, sdr_ddrpll);
	sdram_freq = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(sdr_ddrpll), 1);
	debug("sdram_freq=%lu\n", sdram_freq);

	/*------------------------------------------------------------------
	 * Handle the timing.  We need to find the worst case timing of all
	 * the dimm modules installed.
	 *-----------------------------------------------------------------*/
	t_wr_ns = 0;
	cas_2_0_available = true;
	cas_2_5_available = true;
	cas_3_0_available = true;
	cas_4_0_available = true;
	cas_5_0_available = true;
	max_2_0_tcyc_ns_x_100 = 10;
	max_2_5_tcyc_ns_x_100 = 10;
	max_3_0_tcyc_ns_x_100 = 10;
	max_4_0_tcyc_ns_x_100 = 10;
	max_5_0_tcyc_ns_x_100 = 10;
	sdram_ddr1 = true;

	/* loop through all the DIMM slots on the board */
	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		/* If a dimm is installed in a particular slot ... */
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			if (dimm_populated[dimm_num] == SDRAM_DDR1)
				sdram_ddr1 = true;
			else
				sdram_ddr1 = false;

			cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18);
			debug("cas_bit[SPD byte 18]=%02lx\n", cas_bit);

			/* For a particular DIMM, grab the three CAS values it supports */
			for (cas_index = 0; cas_index < 3; cas_index++) {
				switch (cas_index) {
				case 0:
					tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 9);
					break;
				case 1:
					tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 23);
					break;
				default:
					tcyc_reg = spd_read(iic0_dimm_addr[dimm_num], 25);
					break;
				}

				if ((tcyc_reg & 0x0F) >= 10) {
					if ((tcyc_reg & 0x0F) == 0x0D) {
						/* Convert from hex to decimal */
						cycle_time_ns_x_100[cas_index] =
							(((tcyc_reg & 0xF0) >> 4) * 100) + 75;
					} else {
						printf("ERROR: SPD reported Tcyc is incorrect for DIMM "
						       "in slot %d\n", (unsigned int)dimm_num);
						spd_ddr_init_hang ();
					}
				} else {
					/* Convert from hex to decimal */
					cycle_time_ns_x_100[cas_index] =
						(((tcyc_reg & 0xF0) >> 4) * 100) +
						((tcyc_reg & 0x0F)*10);
				}
				debug("cas_index=%lu: cycle_time_ns_x_100=%lu\n", cas_index,
				      cycle_time_ns_x_100[cas_index]);
			}

			/* The rest of this routine determines if CAS 2.0, 2.5, 3.0, 4.0 and 5.0 are */
			/* supported for a particular DIMM. */
			cas_index = 0;

			if (sdram_ddr1) {
				/*
				 * DDR devices use the following bitmask for CAS latency:
				 *  Bit   7    6    5    4    3    2    1    0
				 *       TBD  4.0  3.5  3.0  2.5  2.0  1.5  1.0
				 */
				if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_4_0_available = false;
				}

				if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_3_0_available = false;
				}

				if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_2_5_available = false;
				}

				if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_2_0_available = false;
				}
			} else {
				/*
				 * DDR2 devices use the following bitmask for CAS latency:
				 *  Bit   7    6    5    4    3    2    1    0
				 *       TBD  6.0  5.0  4.0  3.0  2.0  TBD  TBD
				 */
				if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_5_0_available = false;
				}

				if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_4_0_available = false;
				}

				if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
				    (cycle_time_ns_x_100[cas_index] != 0)) {
					max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
								    cycle_time_ns_x_100[cas_index]);
					cas_index++;
				} else {
					if (cas_index != 0)
						cas_index++;
					cas_3_0_available = false;
				}
			}
		}
	}

	/*------------------------------------------------------------------
	 * Set the SDRAM mode, SDRAM_MMODE
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_MMODE, mmode);
	mmode = mmode & ~(SDRAM_MMODE_WR_MASK | SDRAM_MMODE_DCL_MASK);

	/* add 10 here because of rounding problems */
	cycle_2_0_clk = MULDIV64(ONE_BILLION, 100, max_2_0_tcyc_ns_x_100) + 10;
	cycle_2_5_clk = MULDIV64(ONE_BILLION, 100, max_2_5_tcyc_ns_x_100) + 10;
	cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100) + 10;
	cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100) + 10;
	cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100) + 10;
	debug("cycle_3_0_clk=%lu\n", cycle_3_0_clk);
	debug("cycle_4_0_clk=%lu\n", cycle_4_0_clk);
	debug("cycle_5_0_clk=%lu\n", cycle_5_0_clk);

	if (sdram_ddr1 == true) { /* DDR1 */
		if ((cas_2_0_available == true) &&
			(sdram_freq <= cycle_2_0_clk)) {
			mmode |= SDRAM_MMODE_DCL_DDR1_2_0_CLK;
			*selected_cas = DDR_CAS_2;
		} else if ((cas_2_5_available == true) &&
			(sdram_freq <= cycle_2_5_clk)) {
			mmode |= SDRAM_MMODE_DCL_DDR1_2_5_CLK;
			*selected_cas = DDR_CAS_2_5;
		} else if ((cas_3_0_available == true) &&
			(sdram_freq <= cycle_3_0_clk)) {
			mmode |= SDRAM_MMODE_DCL_DDR1_3_0_CLK;
			*selected_cas = DDR_CAS_3;
		} else {
			printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
			printf("Only DIMMs DDR1 with CAS latencies of 2.0, 2.5, and 3.0 are supported.\n");
			printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n");
			spd_ddr_init_hang ();
		}
	} else { /* DDR2 */
		debug("cas_3_0_available=%d\n", cas_3_0_available);
		debug("cas_4_0_available=%d\n", cas_4_0_available);
		debug("cas_5_0_available=%d\n", cas_5_0_available);
		if ((cas_3_0_available == true) &&
			(sdram_freq <= cycle_3_0_clk)) {
			mmode |= SDRAM_MMODE_DCL_DDR2_3_0_CLK;
			*selected_cas = DDR_CAS_3;
		} else if ((cas_4_0_available == true) &&
			(sdram_freq <= cycle_4_0_clk)) {
			mmode |= SDRAM_MMODE_DCL_DDR2_4_0_CLK;
			*selected_cas = DDR_CAS_4;
		} else if ((cas_5_0_available == true) &&
			(sdram_freq <= cycle_5_0_clk)) {
			mmode |= SDRAM_MMODE_DCL_DDR2_5_0_CLK;
			*selected_cas = DDR_CAS_5;
		} else {
			printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
			printf("Only DIMMs DDR2 with CAS latencies of 3.0, 4.0, and 5.0 are supported.\n");
			printf("Make sure the PLB speed is within the supported range of the DIMMs.\n");
			printf("cas3=%d cas4=%d cas5=%d\n",
			       cas_3_0_available, cas_4_0_available, cas_5_0_available);
			printf("sdram_freq=%lu cycle3=%lu cycle4=%lu cycle5=%lu\n\n",
			       sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk);
			spd_ddr_init_hang ();
		}
	}

	if (sdram_ddr1 == true)
		mmode |= SDRAM_MMODE_WR_DDR1;
	else {

		/* loop through all the DIMM slots on the board */
		for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
			/* If a dimm is installed in a particular slot ... */
			if (dimm_populated[dimm_num] != SDRAM_NONE)
				t_wr_ns = max(t_wr_ns, (unsigned long)
					      spd_read(iic0_dimm_addr[dimm_num], 36) >> 2);
		}

		/*
		 * convert from nanoseconds to ddr clocks
		 * round up if necessary
		 */
		t_wr_clk = MULDIV64(sdram_freq, t_wr_ns, ONE_BILLION);
		ddr_check = MULDIV64(ONE_BILLION, t_wr_clk, t_wr_ns);
		if (sdram_freq != ddr_check)
			t_wr_clk++;

		switch (t_wr_clk) {
		case 0:
		case 1:
		case 2:
		case 3:
			mmode |= SDRAM_MMODE_WR_DDR2_3_CYC;
			break;
		case 4:
			mmode |= SDRAM_MMODE_WR_DDR2_4_CYC;
			break;
		case 5:
			mmode |= SDRAM_MMODE_WR_DDR2_5_CYC;
			break;
		default:
			mmode |= SDRAM_MMODE_WR_DDR2_6_CYC;
			break;
		}
		*write_recovery = t_wr_clk;
	}

	debug("CAS latency = %d\n", *selected_cas);
	debug("Write recovery = %d\n", *write_recovery);

	mtsdram(SDRAM_MMODE, mmode);
}

/*-----------------------------------------------------------------------------+
 * program_rtr.
 *-----------------------------------------------------------------------------*/
static void program_rtr(unsigned long *dimm_populated,
			unsigned char *iic0_dimm_addr,
			unsigned long num_dimm_banks)
{
	PPC4xx_SYS_INFO board_cfg;
	unsigned long max_refresh_rate;
	unsigned long dimm_num;
	unsigned long refresh_rate_type;
	unsigned long refresh_rate;
	unsigned long rint;
	unsigned long sdram_freq;
	unsigned long sdr_ddrpll;
	unsigned long val;

	/*------------------------------------------------------------------
	 * Get the board configuration info.
	 *-----------------------------------------------------------------*/
	get_sys_info(&board_cfg);

	/*------------------------------------------------------------------
	 * Set the SDRAM Refresh Timing Register, SDRAM_RTR
	 *-----------------------------------------------------------------*/
	mfsdr(SDR0_DDR0, sdr_ddrpll);
	sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));

	max_refresh_rate = 0;
	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {

			refresh_rate_type = spd_read(iic0_dimm_addr[dimm_num], 12);
			refresh_rate_type &= 0x7F;
			switch (refresh_rate_type) {
			case 0:
				refresh_rate =  15625;
				break;
			case 1:
				refresh_rate =   3906;
				break;
			case 2:
				refresh_rate =   7812;
				break;
			case 3:
				refresh_rate =  31250;
				break;
			case 4:
				refresh_rate =  62500;
				break;
			case 5:
				refresh_rate = 125000;
				break;
			default:
				refresh_rate = 0;
				printf("ERROR: DIMM %d unsupported refresh rate/type.\n",
				       (unsigned int)dimm_num);
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
				break;
			}

			max_refresh_rate = max(max_refresh_rate, refresh_rate);
		}
	}

	rint = MULDIV64(sdram_freq, max_refresh_rate, ONE_BILLION);
	mfsdram(SDRAM_RTR, val);
	mtsdram(SDRAM_RTR, (val & ~SDRAM_RTR_RINT_MASK) |
		(SDRAM_RTR_RINT_ENCODE(rint)));
}

/*------------------------------------------------------------------
 * This routine programs the SDRAM_TRx registers.
 *-----------------------------------------------------------------*/
static void program_tr(unsigned long *dimm_populated,
		       unsigned char *iic0_dimm_addr,
		       unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long sdram_ddr1;
	unsigned long t_rp_ns;
	unsigned long t_rcd_ns;
	unsigned long t_rrd_ns;
	unsigned long t_ras_ns;
	unsigned long t_rc_ns;
	unsigned long t_rfc_ns;
	unsigned long t_wpc_ns;
	unsigned long t_wtr_ns;
	unsigned long t_rpc_ns;
	unsigned long t_rp_clk;
	unsigned long t_rcd_clk;
	unsigned long t_rrd_clk;
	unsigned long t_ras_clk;
	unsigned long t_rc_clk;
	unsigned long t_rfc_clk;
	unsigned long t_wpc_clk;
	unsigned long t_wtr_clk;
	unsigned long t_rpc_clk;
	unsigned long sdtr1, sdtr2, sdtr3;
	unsigned long ddr_check;
	unsigned long sdram_freq;
	unsigned long sdr_ddrpll;

	PPC4xx_SYS_INFO board_cfg;

	/*------------------------------------------------------------------
	 * Get the board configuration info.
	 *-----------------------------------------------------------------*/
	get_sys_info(&board_cfg);

	mfsdr(SDR0_DDR0, sdr_ddrpll);
	sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));

	/*------------------------------------------------------------------
	 * Handle the timing.  We need to find the worst case timing of all
	 * the dimm modules installed.
	 *-----------------------------------------------------------------*/
	t_rp_ns = 0;
	t_rrd_ns = 0;
	t_rcd_ns = 0;
	t_ras_ns = 0;
	t_rc_ns = 0;
	t_rfc_ns = 0;
	t_wpc_ns = 0;
	t_wtr_ns = 0;
	t_rpc_ns = 0;
	sdram_ddr1 = true;

	/* loop through all the DIMM slots on the board */
	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		/* If a dimm is installed in a particular slot ... */
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			if (dimm_populated[dimm_num] == SDRAM_DDR2)
				sdram_ddr1 = true;
			else
				sdram_ddr1 = false;

			t_rcd_ns = max(t_rcd_ns,
				       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 29) >> 2);
			t_rrd_ns = max(t_rrd_ns,
				       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 28) >> 2);
			t_rp_ns  = max(t_rp_ns,
				       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 27) >> 2);
			t_ras_ns = max(t_ras_ns,
				       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 30));
			t_rc_ns  = max(t_rc_ns,
				       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 41));
			t_rfc_ns = max(t_rfc_ns,
				       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 42));
		}
	}

	/*------------------------------------------------------------------
	 * Set the SDRAM Timing Reg 1, SDRAM_TR1
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_SDTR1, sdtr1);
	sdtr1 &= ~(SDRAM_SDTR1_LDOF_MASK | SDRAM_SDTR1_RTW_MASK |
		   SDRAM_SDTR1_WTWO_MASK | SDRAM_SDTR1_RTRO_MASK);

	/* default values */
	sdtr1 |= SDRAM_SDTR1_LDOF_2_CLK;
	sdtr1 |= SDRAM_SDTR1_RTW_2_CLK;

	/* normal operations */
	sdtr1 |= SDRAM_SDTR1_WTWO_0_CLK;
	sdtr1 |= SDRAM_SDTR1_RTRO_1_CLK;

	mtsdram(SDRAM_SDTR1, sdtr1);

	/*------------------------------------------------------------------
	 * Set the SDRAM Timing Reg 2, SDRAM_TR2
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_SDTR2, sdtr2);
	sdtr2 &= ~(SDRAM_SDTR2_RCD_MASK  | SDRAM_SDTR2_WTR_MASK |
		   SDRAM_SDTR2_XSNR_MASK | SDRAM_SDTR2_WPC_MASK |
		   SDRAM_SDTR2_RPC_MASK  | SDRAM_SDTR2_RP_MASK  |
		   SDRAM_SDTR2_RRD_MASK);

	/*
	 * convert t_rcd from nanoseconds to ddr clocks
	 * round up if necessary
	 */
	t_rcd_clk = MULDIV64(sdram_freq, t_rcd_ns, ONE_BILLION);
	ddr_check = MULDIV64(ONE_BILLION, t_rcd_clk, t_rcd_ns);
	if (sdram_freq != ddr_check)
		t_rcd_clk++;

	switch (t_rcd_clk) {
	case 0:
	case 1:
		sdtr2 |= SDRAM_SDTR2_RCD_1_CLK;
		break;
	case 2:
		sdtr2 |= SDRAM_SDTR2_RCD_2_CLK;
		break;
	case 3:
		sdtr2 |= SDRAM_SDTR2_RCD_3_CLK;
		break;
	case 4:
		sdtr2 |= SDRAM_SDTR2_RCD_4_CLK;
		break;
	default:
		sdtr2 |= SDRAM_SDTR2_RCD_5_CLK;
		break;
	}

	if (sdram_ddr1 == true) { /* DDR1 */
		if (sdram_freq < 200000000) {
			sdtr2 |= SDRAM_SDTR2_WTR_1_CLK;
			sdtr2 |= SDRAM_SDTR2_WPC_2_CLK;
			sdtr2 |= SDRAM_SDTR2_RPC_2_CLK;
		} else {
			sdtr2 |= SDRAM_SDTR2_WTR_2_CLK;
			sdtr2 |= SDRAM_SDTR2_WPC_3_CLK;
			sdtr2 |= SDRAM_SDTR2_RPC_2_CLK;
		}
	} else { /* DDR2 */
		/* loop through all the DIMM slots on the board */
		for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
			/* If a dimm is installed in a particular slot ... */
			if (dimm_populated[dimm_num] != SDRAM_NONE) {
				t_wpc_ns = max(t_wtr_ns,
					       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 36) >> 2);
				t_wtr_ns = max(t_wtr_ns,
					       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 37) >> 2);
				t_rpc_ns = max(t_rpc_ns,
					       (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 38) >> 2);
			}
		}

		/*
		 * convert from nanoseconds to ddr clocks
		 * round up if necessary
		 */
		t_wpc_clk = MULDIV64(sdram_freq, t_wpc_ns, ONE_BILLION);
		ddr_check = MULDIV64(ONE_BILLION, t_wpc_clk, t_wpc_ns);
		if (sdram_freq != ddr_check)
			t_wpc_clk++;

		switch (t_wpc_clk) {
		case 0:
		case 1:
		case 2:
			sdtr2 |= SDRAM_SDTR2_WPC_2_CLK;
			break;
		case 3:
			sdtr2 |= SDRAM_SDTR2_WPC_3_CLK;
			break;
		case 4:
			sdtr2 |= SDRAM_SDTR2_WPC_4_CLK;
			break;
		case 5:
			sdtr2 |= SDRAM_SDTR2_WPC_5_CLK;
			break;
		default:
			sdtr2 |= SDRAM_SDTR2_WPC_6_CLK;
			break;
		}

		/*
		 * convert from nanoseconds to ddr clocks
		 * round up if necessary
		 */
		t_wtr_clk = MULDIV64(sdram_freq, t_wtr_ns, ONE_BILLION);
		ddr_check = MULDIV64(ONE_BILLION, t_wtr_clk, t_wtr_ns);
		if (sdram_freq != ddr_check)
			t_wtr_clk++;

		switch (t_wtr_clk) {
		case 0:
		case 1:
			sdtr2 |= SDRAM_SDTR2_WTR_1_CLK;
			break;
		case 2:
			sdtr2 |= SDRAM_SDTR2_WTR_2_CLK;
			break;
		case 3:
			sdtr2 |= SDRAM_SDTR2_WTR_3_CLK;
			break;
		default:
			sdtr2 |= SDRAM_SDTR2_WTR_4_CLK;
			break;
		}

		/*
		 * convert from nanoseconds to ddr clocks
		 * round up if necessary
		 */
		t_rpc_clk = MULDIV64(sdram_freq, t_rpc_ns, ONE_BILLION);
		ddr_check = MULDIV64(ONE_BILLION, t_rpc_clk, t_rpc_ns);
		if (sdram_freq != ddr_check)
			t_rpc_clk++;

		switch (t_rpc_clk) {
		case 0:
		case 1:
		case 2:
			sdtr2 |= SDRAM_SDTR2_RPC_2_CLK;
			break;
		case 3:
			sdtr2 |= SDRAM_SDTR2_RPC_3_CLK;
			break;
		default:
			sdtr2 |= SDRAM_SDTR2_RPC_4_CLK;
			break;
		}
	}

	/* default value */
	sdtr2 |= SDRAM_SDTR2_XSNR_16_CLK;

	/*
	 * convert t_rrd from nanoseconds to ddr clocks
	 * round up if necessary
	 */
	t_rrd_clk = MULDIV64(sdram_freq, t_rrd_ns, ONE_BILLION);
	ddr_check = MULDIV64(ONE_BILLION, t_rrd_clk, t_rrd_ns);
	if (sdram_freq != ddr_check)
		t_rrd_clk++;

	if (t_rrd_clk == 3)
		sdtr2 |= SDRAM_SDTR2_RRD_3_CLK;
	else
		sdtr2 |= SDRAM_SDTR2_RRD_2_CLK;

	/*
	 * convert t_rp from nanoseconds to ddr clocks
	 * round up if necessary
	 */
	t_rp_clk = MULDIV64(sdram_freq, t_rp_ns, ONE_BILLION);
	ddr_check = MULDIV64(ONE_BILLION, t_rp_clk, t_rp_ns);
	if (sdram_freq != ddr_check)
		t_rp_clk++;

	switch (t_rp_clk) {
	case 0:
	case 1:
	case 2:
	case 3:
		sdtr2 |= SDRAM_SDTR2_RP_3_CLK;
		break;
	case 4:
		sdtr2 |= SDRAM_SDTR2_RP_4_CLK;
		break;
	case 5:
		sdtr2 |= SDRAM_SDTR2_RP_5_CLK;
		break;
	case 6:
		sdtr2 |= SDRAM_SDTR2_RP_6_CLK;
		break;
	default:
		sdtr2 |= SDRAM_SDTR2_RP_7_CLK;
		break;
	}

	mtsdram(SDRAM_SDTR2, sdtr2);

	/*------------------------------------------------------------------
	 * Set the SDRAM Timing Reg 3, SDRAM_TR3
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_SDTR3, sdtr3);
	sdtr3 &= ~(SDRAM_SDTR3_RAS_MASK  | SDRAM_SDTR3_RC_MASK |
		   SDRAM_SDTR3_XCS_MASK | SDRAM_SDTR3_RFC_MASK);

	/*
	 * convert t_ras from nanoseconds to ddr clocks
	 * round up if necessary
	 */
	t_ras_clk = MULDIV64(sdram_freq, t_ras_ns, ONE_BILLION);
	ddr_check = MULDIV64(ONE_BILLION, t_ras_clk, t_ras_ns);
	if (sdram_freq != ddr_check)
		t_ras_clk++;

	sdtr3 |= SDRAM_SDTR3_RAS_ENCODE(t_ras_clk);

	/*
	 * convert t_rc from nanoseconds to ddr clocks
	 * round up if necessary
	 */
	t_rc_clk = MULDIV64(sdram_freq, t_rc_ns, ONE_BILLION);
	ddr_check = MULDIV64(ONE_BILLION, t_rc_clk, t_rc_ns);
	if (sdram_freq != ddr_check)
		t_rc_clk++;

	sdtr3 |= SDRAM_SDTR3_RC_ENCODE(t_rc_clk);

	/* default xcs value */
	sdtr3 |= SDRAM_SDTR3_XCS;

	/*
	 * convert t_rfc from nanoseconds to ddr clocks
	 * round up if necessary
	 */
	t_rfc_clk = MULDIV64(sdram_freq, t_rfc_ns, ONE_BILLION);
	ddr_check = MULDIV64(ONE_BILLION, t_rfc_clk, t_rfc_ns);
	if (sdram_freq != ddr_check)
		t_rfc_clk++;

	sdtr3 |= SDRAM_SDTR3_RFC_ENCODE(t_rfc_clk);

	mtsdram(SDRAM_SDTR3, sdtr3);
}

/*-----------------------------------------------------------------------------+
 * program_bxcf.
 *-----------------------------------------------------------------------------*/
static void program_bxcf(unsigned long *dimm_populated,
			 unsigned char *iic0_dimm_addr,
			 unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	unsigned long num_col_addr;
	unsigned long num_ranks;
	unsigned long num_banks;
	unsigned long mode;
	unsigned long ind_rank;
	unsigned long ind;
	unsigned long ind_bank;
	unsigned long bank_0_populated;

	/*------------------------------------------------------------------
	 * Set the BxCF regs.  First, wipe out the bank config registers.
	 *-----------------------------------------------------------------*/
	mtsdram(SDRAM_MB0CF, 0x00000000);
	mtsdram(SDRAM_MB1CF, 0x00000000);
	mtsdram(SDRAM_MB2CF, 0x00000000);
	mtsdram(SDRAM_MB3CF, 0x00000000);

	mode = SDRAM_BXCF_M_BE_ENABLE;

	bank_0_populated = 0;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			num_col_addr = spd_read(iic0_dimm_addr[dimm_num], 4);
			num_ranks = spd_read(iic0_dimm_addr[dimm_num], 5);
			if ((spd_read(iic0_dimm_addr[dimm_num], 2)) == 0x08)
				num_ranks = (num_ranks & 0x0F) +1;
			else
				num_ranks = num_ranks & 0x0F;

			num_banks = spd_read(iic0_dimm_addr[dimm_num], 17);

			for (ind_bank = 0; ind_bank < 2; ind_bank++) {
				if (num_banks == 4)
					ind = 0;
				else
					ind = 5 << 8;
				switch (num_col_addr) {
				case 0x08:
					mode |= (SDRAM_BXCF_M_AM_0 + ind);
					break;
				case 0x09:
					mode |= (SDRAM_BXCF_M_AM_1 + ind);
					break;
				case 0x0A:
					mode |= (SDRAM_BXCF_M_AM_2 + ind);
					break;
				case 0x0B:
					mode |= (SDRAM_BXCF_M_AM_3 + ind);
					break;
				case 0x0C:
					mode |= (SDRAM_BXCF_M_AM_4 + ind);
					break;
				default:
					printf("DDR-SDRAM: DIMM %d BxCF configuration.\n",
					       (unsigned int)dimm_num);
					printf("ERROR: Unsupported value for number of "
					       "column addresses: %d.\n", (unsigned int)num_col_addr);
					printf("Replace the DIMM module with a supported DIMM.\n\n");
					spd_ddr_init_hang ();
				}
			}

			if ((dimm_populated[dimm_num] != SDRAM_NONE)&& (dimm_num ==1))
				bank_0_populated = 1;

			for (ind_rank = 0; ind_rank < num_ranks; ind_rank++) {
				mtsdram(SDRAM_MB0CF +
					((dimm_num + bank_0_populated + ind_rank) << 2),
					mode);
			}
		}
	}
}

/*------------------------------------------------------------------
 * program memory queue.
 *-----------------------------------------------------------------*/
static void program_memory_queue(unsigned long *dimm_populated,
				 unsigned char *iic0_dimm_addr,
				 unsigned long num_dimm_banks)
{
	unsigned long dimm_num;
	phys_size_t rank_base_addr;
	unsigned long rank_reg;
	phys_size_t rank_size_bytes;
	unsigned long rank_size_id;
	unsigned long num_ranks;
	unsigned long baseadd_size;
	unsigned long i;
	unsigned long bank_0_populated = 0;
	phys_size_t total_size = 0;

	/*------------------------------------------------------------------
	 * Reset the rank_base_address.
	 *-----------------------------------------------------------------*/
	rank_reg   = SDRAM_R0BAS;

	rank_base_addr = 0x00000000;

	for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
		if (dimm_populated[dimm_num] != SDRAM_NONE) {
			num_ranks = spd_read(iic0_dimm_addr[dimm_num], 5);
			if ((spd_read(iic0_dimm_addr[dimm_num], 2)) == 0x08)
				num_ranks = (num_ranks & 0x0F) + 1;
			else
				num_ranks = num_ranks & 0x0F;

			rank_size_id = spd_read(iic0_dimm_addr[dimm_num], 31);

			/*------------------------------------------------------------------
			 * Set the sizes
			 *-----------------------------------------------------------------*/
			baseadd_size = 0;
			switch (rank_size_id) {
			case 0x01:
				baseadd_size |= SDRAM_RXBAS_SDSZ_1024;
				total_size = 1024;
				break;
			case 0x02:
				baseadd_size |= SDRAM_RXBAS_SDSZ_2048;
				total_size = 2048;
				break;
			case 0x04:
				baseadd_size |= SDRAM_RXBAS_SDSZ_4096;
				total_size = 4096;
				break;
			case 0x08:
				baseadd_size |= SDRAM_RXBAS_SDSZ_32;
				total_size = 32;
				break;
			case 0x10:
				baseadd_size |= SDRAM_RXBAS_SDSZ_64;
				total_size = 64;
				break;
			case 0x20:
				baseadd_size |= SDRAM_RXBAS_SDSZ_128;
				total_size = 128;
				break;
			case 0x40:
				baseadd_size |= SDRAM_RXBAS_SDSZ_256;
				total_size = 256;
				break;
			case 0x80:
				baseadd_size |= SDRAM_RXBAS_SDSZ_512;
				total_size = 512;
				break;
			default:
				printf("DDR-SDRAM: DIMM %d memory queue configuration.\n",
				       (unsigned int)dimm_num);
				printf("ERROR: Unsupported value for the banksize: %d.\n",
				       (unsigned int)rank_size_id);
				printf("Replace the DIMM module with a supported DIMM.\n\n");
				spd_ddr_init_hang ();
			}
			rank_size_bytes = total_size << 20;

			if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1))
				bank_0_populated = 1;

			for (i = 0; i < num_ranks; i++)	{
				mtdcr_any(rank_reg+i+dimm_num+bank_0_populated,
					  (SDRAM_RXBAS_SDBA_ENCODE(rank_base_addr) |
					   baseadd_size));
				rank_base_addr += rank_size_bytes;
			}
		}
	}

#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
    defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
    defined(CONFIG_460SX)
	/*
	 * Enable high bandwidth access
	 * This is currently not used, but with this setup
	 * it is possible to use it later on in e.g. the Linux
	 * EMAC driver for performance gain.
	 */
	mtdcr(SDRAM_PLBADDULL, 0x00000000); /* MQ0_BAUL */
	mtdcr(SDRAM_PLBADDUHB, 0x00000008); /* MQ0_BAUH */

	/*
	 * Set optimal value for Memory Queue HB/LL Configuration registers
	 */
	mtdcr(SDRAM_CONF1HB, (mfdcr(SDRAM_CONF1HB) & ~SDRAM_CONF1HB_MASK) |
	      SDRAM_CONF1HB_AAFR | SDRAM_CONF1HB_RPEN | SDRAM_CONF1HB_RFTE |
	      SDRAM_CONF1HB_RPLM | SDRAM_CONF1HB_WRCL);
	mtdcr(SDRAM_CONF1LL, (mfdcr(SDRAM_CONF1LL) & ~SDRAM_CONF1LL_MASK) |
	      SDRAM_CONF1LL_AAFR | SDRAM_CONF1LL_RPEN | SDRAM_CONF1LL_RFTE |
	      SDRAM_CONF1LL_RPLM);
	mtdcr(SDRAM_CONFPATHB, mfdcr(SDRAM_CONFPATHB) | SDRAM_CONFPATHB_TPEN);
#endif
}

#ifdef CONFIG_DDR_ECC
/*-----------------------------------------------------------------------------+
 * program_ecc.
 *-----------------------------------------------------------------------------*/
static void program_ecc(unsigned long *dimm_populated,
			unsigned char *iic0_dimm_addr,
			unsigned long num_dimm_banks,
			unsigned long tlb_word2_i_value)
{
	unsigned long dimm_num;
	unsigned long ecc;

	ecc = 0;
	/* loop through all the DIMM slots on the board */
	for (dimm_num = 0; dimm_num < MAXDIMMS; dimm_num++) {
		/* If a dimm is installed in a particular slot ... */
		if (dimm_populated[dimm_num] != SDRAM_NONE)
			ecc = max(ecc,
				  (unsigned long)spd_read(iic0_dimm_addr[dimm_num], 11));
	}
	if (ecc == 0)
		return;

	do_program_ecc(tlb_word2_i_value);
}
#endif

#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
/*-----------------------------------------------------------------------------+
 * program_DQS_calibration.
 *-----------------------------------------------------------------------------*/
static void program_DQS_calibration(unsigned long *dimm_populated,
				    unsigned char *iic0_dimm_addr,
				    unsigned long num_dimm_banks)
{
	unsigned long val;

#ifdef HARD_CODED_DQS /* calibration test with hardvalues */
	mtsdram(SDRAM_RQDC, 0x80000037);
	mtsdram(SDRAM_RDCC, 0x40000000);
	mtsdram(SDRAM_RFDC, 0x000001DF);

	test();
#else
	/*------------------------------------------------------------------
	 * Program RDCC register
	 * Read sample cycle auto-update enable
	 *-----------------------------------------------------------------*/

	mfsdram(SDRAM_RDCC, val);
	mtsdram(SDRAM_RDCC,
		(val & ~(SDRAM_RDCC_RDSS_MASK | SDRAM_RDCC_RSAE_MASK))
		| SDRAM_RDCC_RSAE_ENABLE);

	/*------------------------------------------------------------------
	 * Program RQDC register
	 * Internal DQS delay mechanism enable
	 *-----------------------------------------------------------------*/
	mtsdram(SDRAM_RQDC, (SDRAM_RQDC_RQDE_ENABLE|SDRAM_RQDC_RQFD_ENCODE(0x38)));

	/*------------------------------------------------------------------
	 * Program RFDC register
	 * Set Feedback Fractional Oversample
	 * Auto-detect read sample cycle enable
	 * Set RFOS to 1/4 of memclk cycle (0x3f)
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_RFDC, val);
	mtsdram(SDRAM_RFDC,
		(val & ~(SDRAM_RFDC_ARSE_MASK | SDRAM_RFDC_RFOS_MASK |
			 SDRAM_RFDC_RFFD_MASK))
		| (SDRAM_RFDC_ARSE_ENABLE | SDRAM_RFDC_RFOS_ENCODE(0x3f) |
		   SDRAM_RFDC_RFFD_ENCODE(0)));

	DQS_calibration_process();
#endif
}

static int short_mem_test(void)
{
	u32 *membase;
	u32 bxcr_num;
	u32 bxcf;
	int i;
	int j;
	phys_size_t base_addr;
	u32 test[NUMMEMTESTS][NUMMEMWORDS] = {
		{0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
		 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF},
		{0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
		 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000},
		{0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
		 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555},
		{0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
		 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA},
		{0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
		 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A},
		{0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
		 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5},
		{0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
		 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA},
		{0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
		 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55} };
	int l;

	for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) {
		mfsdram(SDRAM_MB0CF + (bxcr_num << 2), bxcf);

		/* Banks enabled */
		if ((bxcf & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {
			/* Bank is enabled */

			/*
			 * Only run test on accessable memory (below 2GB)
			 */
			base_addr = SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num));
			if (base_addr >= CONFIG_MAX_MEM_MAPPED)
				continue;

			/*------------------------------------------------------------------
			 * Run the short memory test.
			 *-----------------------------------------------------------------*/
			membase = (u32 *)(u32)base_addr;

			for (i = 0; i < NUMMEMTESTS; i++) {
				for (j = 0; j < NUMMEMWORDS; j++) {
					membase[j] = test[i][j];
					ppcDcbf((u32)&(membase[j]));
				}
				sync();
				for (l=0; l<NUMLOOPS; l++) {
					for (j = 0; j < NUMMEMWORDS; j++) {
						if (membase[j] != test[i][j]) {
							ppcDcbf((u32)&(membase[j]));
							return 0;
						}
						ppcDcbf((u32)&(membase[j]));
					}
					sync();
				}
			}
		}	/* if bank enabled */
	}		/* for bxcf_num */

	return 1;
}

#ifndef HARD_CODED_DQS
/*-----------------------------------------------------------------------------+
 * DQS_calibration_process.
 *-----------------------------------------------------------------------------*/
static void DQS_calibration_process(void)
{
	unsigned long rfdc_reg;
	unsigned long rffd;
	unsigned long val;
	long rffd_average;
	long max_start;
	unsigned long dlycal;
	unsigned long dly_val;
	unsigned long max_pass_length;
	unsigned long current_pass_length;
	unsigned long current_fail_length;
	unsigned long current_start;
	long max_end;
	unsigned char fail_found;
	unsigned char pass_found;
#if !defined(CONFIG_DDR_RQDC_FIXED)
	int window_found;
	u32 rqdc_reg;
	u32 rqfd;
	u32 rqfd_start;
	u32 rqfd_average;
	int loopi = 0;
	char str[] = "Auto calibration -";
	char slash[] = "\\|/-\\|/-";

	/*------------------------------------------------------------------
	 * Test to determine the best read clock delay tuning bits.
	 *
	 * Before the DDR controller can be used, the read clock delay needs to be
	 * set.  This is SDRAM_RQDC[RQFD] and SDRAM_RFDC[RFFD].
	 * This value cannot be hardcoded into the program because it changes
	 * depending on the board's setup and environment.
	 * To do this, all delay values are tested to see if they
	 * work or not.  By doing this, you get groups of fails with groups of
	 * passing values.  The idea is to find the start and end of a passing
	 * window and take the center of it to use as the read clock delay.
	 *
	 * A failure has to be seen first so that when we hit a pass, we know
	 * that it is truely the start of the window.  If we get passing values
	 * to start off with, we don't know if we are at the start of the window.
	 *
	 * The code assumes that a failure will always be found.
	 * If a failure is not found, there is no easy way to get the middle
	 * of the passing window.  I guess we can pretty much pick any value
	 * but some values will be better than others.  Since the lowest speed
	 * we can clock the DDR interface at is 200 MHz (2x 100 MHz PLB speed),
	 * from experimentation it is safe to say you will always have a failure.
	 *-----------------------------------------------------------------*/

	/* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
	rqfd_start = 64; /* test-only: don't know if this is the _best_ start value */

	puts(str);

calibration_loop:
	mfsdram(SDRAM_RQDC, rqdc_reg);
	mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
		SDRAM_RQDC_RQFD_ENCODE(rqfd_start));
#else /* CONFIG_DDR_RQDC_FIXED */
	/*
	 * On Katmai the complete auto-calibration somehow doesn't seem to
	 * produce the best results, meaning optimal values for RQFD/RFFD.
	 * This was discovered by GDA using a high bandwidth scope,
	 * analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
	 * so now on Katmai "only" RFFD is auto-calibrated.
	 */
	mtsdram(SDRAM_RQDC, CONFIG_DDR_RQDC_FIXED);
#endif /* CONFIG_DDR_RQDC_FIXED */

	max_start = 0;

	max_pass_length = 0;
	max_start = 0;
	max_end = 0;
	current_pass_length = 0;
	current_fail_length = 0;
	current_start = 0;
	fail_found = false;
	pass_found = false;

	/*
	 * get the delay line calibration register value
	 */
	mfsdram(SDRAM_DLCR, dlycal);
	dly_val = SDRAM_DLYCAL_DLCV_DECODE(dlycal) << 2;

	for (rffd = 0; rffd <= SDRAM_RFDC_RFFD_MAX; rffd++) {
		mfsdram(SDRAM_RFDC, rfdc_reg);
		rfdc_reg &= ~(SDRAM_RFDC_RFFD_MASK);

		/*------------------------------------------------------------------
		 * Set the timing reg for the test.
		 *-----------------------------------------------------------------*/
		mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd));

		/*------------------------------------------------------------------
		 * See if the rffd value passed.
		 *-----------------------------------------------------------------*/
		if (short_mem_test()) {
			if (fail_found == true) {
				pass_found = true;
				if (current_pass_length == 0)
					current_start = rffd;

				current_fail_length = 0;
				current_pass_length++;

				if (current_pass_length > max_pass_length) {
					max_pass_length = current_pass_length;
					max_start = current_start;
					max_end = rffd;
				}
			}
		} else {
			current_pass_length = 0;
			current_fail_length++;

			if (current_fail_length >= (dly_val >> 2)) {
				if (fail_found == false)
					fail_found = true;
				else if (pass_found == true)
					break;
			}
		}
	}		/* for rffd */

	/*------------------------------------------------------------------
	 * Set the average RFFD value
	 *-----------------------------------------------------------------*/
	rffd_average = ((max_start + max_end) >> 1);

	if (rffd_average < 0)
		rffd_average = 0;

	if (rffd_average > SDRAM_RFDC_RFFD_MAX)
		rffd_average = SDRAM_RFDC_RFFD_MAX;
	/* now fix RFDC[RFFD] found and find RQDC[RQFD] */
	mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd_average));

#if !defined(CONFIG_DDR_RQDC_FIXED)
	max_pass_length = 0;
	max_start = 0;
	max_end = 0;
	current_pass_length = 0;
	current_fail_length = 0;
	current_start = 0;
	window_found = false;
	fail_found = false;
	pass_found = false;

	for (rqfd = 0; rqfd <= SDRAM_RQDC_RQFD_MAX; rqfd++) {
		mfsdram(SDRAM_RQDC, rqdc_reg);
		rqdc_reg &= ~(SDRAM_RQDC_RQFD_MASK);

		/*------------------------------------------------------------------
		 * Set the timing reg for the test.
		 *-----------------------------------------------------------------*/
		mtsdram(SDRAM_RQDC, rqdc_reg | SDRAM_RQDC_RQFD_ENCODE(rqfd));

		/*------------------------------------------------------------------
		 * See if the rffd value passed.
		 *-----------------------------------------------------------------*/
		if (short_mem_test()) {
			if (fail_found == true) {
				pass_found = true;
				if (current_pass_length == 0)
					current_start = rqfd;

				current_fail_length = 0;
				current_pass_length++;

				if (current_pass_length > max_pass_length) {
					max_pass_length = current_pass_length;
					max_start = current_start;
					max_end = rqfd;
				}
			}
		} else {
			current_pass_length = 0;
			current_fail_length++;

			if (fail_found == false) {
				fail_found = true;
			} else if (pass_found == true) {
				window_found = true;
				break;
			}
		}
	}

	rqfd_average = ((max_start + max_end) >> 1);

	/*------------------------------------------------------------------
	 * Make sure we found the valid read passing window.  Halt if not
	 *-----------------------------------------------------------------*/
	if (window_found == false) {
		if (rqfd_start < SDRAM_RQDC_RQFD_MAX) {
			putc('\b');
			putc(slash[loopi++ % 8]);

			/* try again from with a different RQFD start value */
			rqfd_start++;
			goto calibration_loop;
		}

		printf("\nERROR: Cannot determine a common read delay for the "
		       "DIMM(s) installed.\n");
		debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__);
		ppc4xx_ibm_ddr2_register_dump();
		spd_ddr_init_hang ();
	}

	if (rqfd_average < 0)
		rqfd_average = 0;

	if (rqfd_average > SDRAM_RQDC_RQFD_MAX)
		rqfd_average = SDRAM_RQDC_RQFD_MAX;

	mtsdram(SDRAM_RQDC,
		(rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
		SDRAM_RQDC_RQFD_ENCODE(rqfd_average));

	blank_string(strlen(str));
#endif /* CONFIG_DDR_RQDC_FIXED */

	mfsdram(SDRAM_DLCR, val);
	debug("%s[%d] DLCR: 0x%08lX\n", __FUNCTION__, __LINE__, val);
	mfsdram(SDRAM_RQDC, val);
	debug("%s[%d] RQDC: 0x%08lX\n", __FUNCTION__, __LINE__, val);
	mfsdram(SDRAM_RFDC, val);
	debug("%s[%d] RFDC: 0x%08lX\n", __FUNCTION__, __LINE__, val);
	mfsdram(SDRAM_RDCC, val);
	debug("%s[%d] RDCC: 0x%08lX\n", __FUNCTION__, __LINE__, val);
}
#else /* calibration test with hardvalues */
/*-----------------------------------------------------------------------------+
 * DQS_calibration_process.
 *-----------------------------------------------------------------------------*/
static void test(void)
{
	unsigned long dimm_num;
	unsigned long ecc_temp;
	unsigned long i, j;
	unsigned long *membase;
	unsigned long bxcf[MAXRANKS];
	unsigned long val;
	char window_found;
	char begin_found[MAXDIMMS];
	char end_found[MAXDIMMS];
	char search_end[MAXDIMMS];
	unsigned long test[NUMMEMTESTS][NUMMEMWORDS] = {
		{0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
		 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF},
		{0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
		 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000},
		{0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
		 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555},
		{0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
		 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA},
		{0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
		 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A},
		{0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
		 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5},
		{0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
		 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA},
		{0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
		 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55} };

	/*------------------------------------------------------------------
	 * Test to determine the best read clock delay tuning bits.
	 *
	 * Before the DDR controller can be used, the read clock delay needs to be
	 * set.  This is SDRAM_RQDC[RQFD] and SDRAM_RFDC[RFFD].
	 * This value cannot be hardcoded into the program because it changes
	 * depending on the board's setup and environment.
	 * To do this, all delay values are tested to see if they
	 * work or not.  By doing this, you get groups of fails with groups of
	 * passing values.  The idea is to find the start and end of a passing
	 * window and take the center of it to use as the read clock delay.
	 *
	 * A failure has to be seen first so that when we hit a pass, we know
	 * that it is truely the start of the window.  If we get passing values
	 * to start off with, we don't know if we are at the start of the window.
	 *
	 * The code assumes that a failure will always be found.
	 * If a failure is not found, there is no easy way to get the middle
	 * of the passing window.  I guess we can pretty much pick any value
	 * but some values will be better than others.  Since the lowest speed
	 * we can clock the DDR interface at is 200 MHz (2x 100 MHz PLB speed),
	 * from experimentation it is safe to say you will always have a failure.
	 *-----------------------------------------------------------------*/
	mfsdram(SDRAM_MCOPT1, ecc_temp);
	ecc_temp &= SDRAM_MCOPT1_MCHK_MASK;
	mfsdram(SDRAM_MCOPT1, val);
	mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) |
		SDRAM_MCOPT1_MCHK_NON);

	window_found = false;
	begin_found[0] = false;
	end_found[0] = false;
	search_end[0] = false;
	begin_found[1] = false;
	end_found[1] = false;
	search_end[1] = false;

	for (dimm_num = 0; dimm_num < MAXDIMMS; dimm_num++) {
		mfsdram(SDRAM_MB0CF + (bxcr_num << 2), bxcf[bxcr_num]);

		/* Banks enabled */
		if ((bxcf[dimm_num] & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {

			/* Bank is enabled */
			membase =
				(unsigned long*)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+dimm_num)));

			/*------------------------------------------------------------------
			 * Run the short memory test.
			 *-----------------------------------------------------------------*/
			for (i = 0; i < NUMMEMTESTS; i++) {
				for (j = 0; j < NUMMEMWORDS; j++) {
					membase[j] = test[i][j];
					ppcDcbf((u32)&(membase[j]));
				}
				sync();
				for (j = 0; j < NUMMEMWORDS; j++) {
					if (membase[j] != test[i][j]) {
						ppcDcbf((u32)&(membase[j]));
						break;
					}
					ppcDcbf((u32)&(membase[j]));
				}
				sync();
				if (j < NUMMEMWORDS)
					break;
			}

			/*------------------------------------------------------------------
			 * See if the rffd value passed.
			 *-----------------------------------------------------------------*/
			if (i < NUMMEMTESTS) {
				if ((end_found[dimm_num] == false) &&
				    (search_end[dimm_num] == true)) {
					end_found[dimm_num] = true;
				}
				if ((end_found[0] == true) &&
				    (end_found[1] == true))
					break;
			} else {
				if (begin_found[dimm_num] == false) {
					begin_found[dimm_num] = true;
					search_end[dimm_num] = true;
				}
			}
		} else {
			begin_found[dimm_num] = true;
			end_found[dimm_num] = true;
		}
	}

	if ((begin_found[0] == true) && (begin_found[1] == true))
		window_found = true;

	/*------------------------------------------------------------------
	 * Make sure we found the valid read passing window.  Halt if not
	 *-----------------------------------------------------------------*/
	if (window_found == false) {
		printf("ERROR: Cannot determine a common read delay for the "
		       "DIMM(s) installed.\n");
		spd_ddr_init_hang ();
	}

	/*------------------------------------------------------------------
	 * Restore the ECC variable to what it originally was
	 *-----------------------------------------------------------------*/
	mtsdram(SDRAM_MCOPT1,
		(ppcMfdcr_sdram(SDRAM_MCOPT1) & ~SDRAM_MCOPT1_MCHK_MASK)
		| ecc_temp);
}
#endif /* !HARD_CODED_DQS */
#endif /* !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) */

#else /* CONFIG_SPD_EEPROM */

/*-----------------------------------------------------------------------------
 * Function:	initdram
 * Description: Configures the PPC4xx IBM DDR1/DDR2 SDRAM memory controller.
 * 		The configuration is performed using static, compile-
 *		time parameters.
 * 		Configures the PPC405EX(r) and PPC460EX/GT
 *---------------------------------------------------------------------------*/
phys_size_t initdram(int board_type)
{
	unsigned long val;

#if defined(CONFIG_440)
	mtdcr(SDRAM_R0BAS,	CONFIG_SYS_SDRAM_R0BAS);
	mtdcr(SDRAM_R1BAS,	CONFIG_SYS_SDRAM_R1BAS);
	mtdcr(SDRAM_R2BAS,	CONFIG_SYS_SDRAM_R2BAS);
	mtdcr(SDRAM_R3BAS,	CONFIG_SYS_SDRAM_R3BAS);
	mtdcr(SDRAM_PLBADDULL,	CONFIG_SYS_SDRAM_PLBADDULL);	/* MQ0_BAUL */
	mtdcr(SDRAM_PLBADDUHB,	CONFIG_SYS_SDRAM_PLBADDUHB);	/* MQ0_BAUH */
	mtdcr(SDRAM_CONF1LL,	CONFIG_SYS_SDRAM_CONF1LL);
	mtdcr(SDRAM_CONF1HB,	CONFIG_SYS_SDRAM_CONF1HB);
	mtdcr(SDRAM_CONFPATHB,	CONFIG_SYS_SDRAM_CONFPATHB);
#endif

	/* Set Memory Bank Configuration Registers */

	mtsdram(SDRAM_MB0CF, CONFIG_SYS_SDRAM0_MB0CF);
	mtsdram(SDRAM_MB1CF, CONFIG_SYS_SDRAM0_MB1CF);
	mtsdram(SDRAM_MB2CF, CONFIG_SYS_SDRAM0_MB2CF);
	mtsdram(SDRAM_MB3CF, CONFIG_SYS_SDRAM0_MB3CF);

	/* Set Memory Clock Timing Register */

	mtsdram(SDRAM_CLKTR, CONFIG_SYS_SDRAM0_CLKTR);

	/* Set Refresh Time Register */

	mtsdram(SDRAM_RTR, CONFIG_SYS_SDRAM0_RTR);

	/* Set SDRAM Timing Registers */

	mtsdram(SDRAM_SDTR1, CONFIG_SYS_SDRAM0_SDTR1);
	mtsdram(SDRAM_SDTR2, CONFIG_SYS_SDRAM0_SDTR2);
	mtsdram(SDRAM_SDTR3, CONFIG_SYS_SDRAM0_SDTR3);

	/* Set Mode and Extended Mode Registers */

	mtsdram(SDRAM_MMODE, CONFIG_SYS_SDRAM0_MMODE);
	mtsdram(SDRAM_MEMODE, CONFIG_SYS_SDRAM0_MEMODE);

	/* Set Memory Controller Options 1 Register */

	mtsdram(SDRAM_MCOPT1, CONFIG_SYS_SDRAM0_MCOPT1);

	/* Set Manual Initialization Control Registers */

	mtsdram(SDRAM_INITPLR0, CONFIG_SYS_SDRAM0_INITPLR0);
	mtsdram(SDRAM_INITPLR1, CONFIG_SYS_SDRAM0_INITPLR1);
	mtsdram(SDRAM_INITPLR2, CONFIG_SYS_SDRAM0_INITPLR2);
	mtsdram(SDRAM_INITPLR3, CONFIG_SYS_SDRAM0_INITPLR3);
	mtsdram(SDRAM_INITPLR4, CONFIG_SYS_SDRAM0_INITPLR4);
	mtsdram(SDRAM_INITPLR5, CONFIG_SYS_SDRAM0_INITPLR5);
	mtsdram(SDRAM_INITPLR6, CONFIG_SYS_SDRAM0_INITPLR6);
	mtsdram(SDRAM_INITPLR7, CONFIG_SYS_SDRAM0_INITPLR7);
	mtsdram(SDRAM_INITPLR8, CONFIG_SYS_SDRAM0_INITPLR8);
	mtsdram(SDRAM_INITPLR9, CONFIG_SYS_SDRAM0_INITPLR9);
	mtsdram(SDRAM_INITPLR10, CONFIG_SYS_SDRAM0_INITPLR10);
	mtsdram(SDRAM_INITPLR11, CONFIG_SYS_SDRAM0_INITPLR11);
	mtsdram(SDRAM_INITPLR12, CONFIG_SYS_SDRAM0_INITPLR12);
	mtsdram(SDRAM_INITPLR13, CONFIG_SYS_SDRAM0_INITPLR13);
	mtsdram(SDRAM_INITPLR14, CONFIG_SYS_SDRAM0_INITPLR14);
	mtsdram(SDRAM_INITPLR15, CONFIG_SYS_SDRAM0_INITPLR15);

	/* Set On-Die Termination Registers */

	mtsdram(SDRAM_CODT, CONFIG_SYS_SDRAM0_CODT);
	mtsdram(SDRAM_MODT0, CONFIG_SYS_SDRAM0_MODT0);
	mtsdram(SDRAM_MODT1, CONFIG_SYS_SDRAM0_MODT1);

	/* Set Write Timing Register */

	mtsdram(SDRAM_WRDTR, CONFIG_SYS_SDRAM0_WRDTR);

	/*
	 * Start Initialization by SDRAM0_MCOPT2[SREN] = 0 and
	 * SDRAM0_MCOPT2[IPTR] = 1
	 */

	mtsdram(SDRAM_MCOPT2, (SDRAM_MCOPT2_SREN_EXIT |
			       SDRAM_MCOPT2_IPTR_EXECUTE));

	/*
	 * Poll SDRAM0_MCSTAT[MIC] for assertion to indicate the
	 * completion of initialization.
	 */

	do {
		mfsdram(SDRAM_MCSTAT, val);
	} while ((val & SDRAM_MCSTAT_MIC_MASK) != SDRAM_MCSTAT_MIC_COMP);

	/* Set Delay Control Registers */

	mtsdram(SDRAM_DLCR, CONFIG_SYS_SDRAM0_DLCR);

#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
	mtsdram(SDRAM_RDCC, CONFIG_SYS_SDRAM0_RDCC);
	mtsdram(SDRAM_RQDC, CONFIG_SYS_SDRAM0_RQDC);
	mtsdram(SDRAM_RFDC, CONFIG_SYS_SDRAM0_RFDC);
#endif /* !CONFIG_PPC4xx_DDR_AUTOCALIBRATION */

	/*
	 * Enable Controller by SDRAM0_MCOPT2[DCEN] = 1:
	 */

	mfsdram(SDRAM_MCOPT2, val);
	mtsdram(SDRAM_MCOPT2, val | SDRAM_MCOPT2_DCEN_ENABLE);

#if defined(CONFIG_440)
	/*
	 * Program TLB entries with caches enabled, for best performace
	 * while auto-calibrating and ECC generation
	 */
	program_tlb(0, 0, (CONFIG_SYS_MBYTES_SDRAM << 20), 0);
#endif

#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
	/*------------------------------------------------------------------
	 | DQS calibration.
	 +-----------------------------------------------------------------*/
	DQS_autocalibration();
#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */

	/*
	 * Now complete RDSS configuration as mentioned on page 7 of the AMCC
	 * PowerPC440SP/SPe DDR2 application note:
	 * "DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
	 */
	update_rdcc();

#if defined(CONFIG_DDR_ECC)
	do_program_ecc(0);
#endif /* defined(CONFIG_DDR_ECC) */

#if defined(CONFIG_440)
	/*
	 * Now after initialization (auto-calibration and ECC generation)
	 * remove the TLB entries with caches enabled and program again with
	 * desired cache functionality
	 */
	remove_tlb(0, (CONFIG_SYS_MBYTES_SDRAM << 20));
	program_tlb(0, 0, (CONFIG_SYS_MBYTES_SDRAM << 20), MY_TLB_WORD2_I_ENABLE);
#endif

	ppc4xx_ibm_ddr2_register_dump();

#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION)
	/*
	 * Clear potential errors resulting from auto-calibration.
	 * If not done, then we could get an interrupt later on when
	 * exceptions are enabled.
	 */
	set_mcsr(get_mcsr());
#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */

	return (CONFIG_SYS_MBYTES_SDRAM << 20);
}
#endif /* CONFIG_SPD_EEPROM */

#if defined(CONFIG_440)
u32 mfdcr_any(u32 dcr)
{
	u32 val;

	switch (dcr) {
	case SDRAM_R0BAS + 0:
		val = mfdcr(SDRAM_R0BAS + 0);
		break;
	case SDRAM_R0BAS + 1:
		val = mfdcr(SDRAM_R0BAS + 1);
		break;
	case SDRAM_R0BAS + 2:
		val = mfdcr(SDRAM_R0BAS + 2);
		break;
	case SDRAM_R0BAS + 3:
		val = mfdcr(SDRAM_R0BAS + 3);
		break;
	default:
		printf("DCR %d not defined in case statement!!!\n", dcr);
		val = 0; /* just to satisfy the compiler */
	}

	return val;
}

void mtdcr_any(u32 dcr, u32 val)
{
	switch (dcr) {
	case SDRAM_R0BAS + 0:
		mtdcr(SDRAM_R0BAS + 0, val);
		break;
	case SDRAM_R0BAS + 1:
		mtdcr(SDRAM_R0BAS + 1, val);
		break;
	case SDRAM_R0BAS + 2:
		mtdcr(SDRAM_R0BAS + 2, val);
		break;
	case SDRAM_R0BAS + 3:
		mtdcr(SDRAM_R0BAS + 3, val);
		break;
	default:
		printf("DCR %d not defined in case statement!!!\n", dcr);
	}
}
#endif /* defined(CONFIG_440) */

inline void ppc4xx_ibm_ddr2_register_dump(void)
{
#if defined(DEBUG)
	printf("\nPPC4xx IBM DDR2 Register Dump:\n");

#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
     defined(CONFIG_460EX) || defined(CONFIG_460GT))
	PPC4xx_IBM_DDR2_DUMP_MQ_REGISTER(R0BAS);
	PPC4xx_IBM_DDR2_DUMP_MQ_REGISTER(R1BAS);
	PPC4xx_IBM_DDR2_DUMP_MQ_REGISTER(R2BAS);
	PPC4xx_IBM_DDR2_DUMP_MQ_REGISTER(R3BAS);
#endif /* (defined(CONFIG_440SP) || ... */
#if defined(CONFIG_405EX)
	PPC4xx_IBM_DDR2_DUMP_REGISTER(BESR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(BEARL);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(BEARH);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(WMIRQ);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(PLBOPT);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(PUABA);
#endif /* defined(CONFIG_405EX) */
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MB0CF);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MB1CF);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MB2CF);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MB3CF);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MCSTAT);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MCOPT1);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MCOPT2);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT0);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT1);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT2);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT3);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(CODT);
#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) ||	\
     defined(CONFIG_460EX) || defined(CONFIG_460GT))
	PPC4xx_IBM_DDR2_DUMP_REGISTER(VVPR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(OPARS);
	/*
	 * OPART is only used as a trigger register.
	 *
	 * No data is contained in this register, and reading or writing
	 * to is can cause bad things to happen (hangs). Just skip it and
	 * report "N/A".
	 */
	printf("%20s = N/A\n", "SDRAM_OPART");
#endif /* defined(CONFIG_440SP) || ... */
	PPC4xx_IBM_DDR2_DUMP_REGISTER(RTR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR0);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR1);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR2);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR3);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR4);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR5);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR6);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR7);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR8);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR9);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR10);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR11);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR12);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR13);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR14);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR15);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(RQDC);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(RFDC);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(RDCC);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(DLCR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(CLKTR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(WRDTR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR1);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR2);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR3);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MMODE);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(MEMODE);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(ECCES);
#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
     defined(CONFIG_460EX) || defined(CONFIG_460GT))
	PPC4xx_IBM_DDR2_DUMP_REGISTER(CID);
#endif /* defined(CONFIG_440SP) || ... */
	PPC4xx_IBM_DDR2_DUMP_REGISTER(RID);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(FCSR);
	PPC4xx_IBM_DDR2_DUMP_REGISTER(RTSR);
#endif /* defined(DEBUG) */
}