/*
 * Copyright (C) 2012 Marek Vasut <marex@denx.de>
 * on behalf of DENX Software Engineering GmbH
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <miiphy.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
#include <asm/io.h>

DECLARE_GLOBAL_DATA_PTR;

#define TK71_OE_LOW			(~0)
#define TK71_OE_HIGH			(~0)
#define TK71_OE_VAL_LOW			(0)
#define TK71_OE_VAL_HIGH		(0)

int board_early_init_f(void)
{
	/*
	 * default gpio configuration
	 * There are maximum 64 gpios controlled through 2 sets of registers
	 * the  below configuration configures mainly initial LED status
	 */
	mvebu_config_gpio(TK71_OE_VAL_LOW,
			  TK71_OE_VAL_HIGH,
			  TK71_OE_LOW, TK71_OE_HIGH);

	/* Multi-Purpose Pins Functionality configuration */
	static const u32 kwmpp_config[] = {
		MPP0_NF_IO2,
		MPP1_NF_IO3,
		MPP2_NF_IO4,
		MPP3_NF_IO5,
		MPP4_NF_IO6,
		MPP5_NF_IO7,
		MPP6_SYSRST_OUTn,
		MPP7_GPO,
		MPP8_TW_SDA,
		MPP9_TW_SCK,
		MPP10_UART0_TXD,
		MPP11_UART0_RXD,
		MPP12_SD_CLK,
		MPP13_SD_CMD,
		MPP14_SD_D0,
		MPP15_SD_D1,
		MPP16_SD_D2,
		MPP17_SD_D3,
		MPP18_NF_IO0,
		MPP19_NF_IO1,
		MPP20_GE1_0,
		MPP21_GE1_1,
		MPP22_GE1_2,
		MPP23_GE1_3,
		MPP24_GE1_4,
		MPP25_GE1_5,
		MPP26_GE1_6,
		MPP27_GE1_7,
		MPP28_GPIO,
		MPP29_GPIO,
		MPP30_GE1_10,
		MPP31_GE1_11,
		MPP32_GE1_12,
		MPP33_GE1_13,
		MPP34_GPIO,
		MPP35_GPIO,
		MPP36_GPIO,
		MPP37_GPIO,
		MPP38_GPIO,
		MPP39_GPIO,
		MPP40_GPIO,
		MPP41_GPIO,
		MPP42_GPIO,
		MPP43_GPIO,
		MPP44_GPIO,
		MPP45_GPIO,
		MPP46_GPIO,
		MPP47_GPIO,
		MPP48_GPIO,
		MPP49_GPIO,
		0
	};
	kirkwood_mpp_conf(kwmpp_config, NULL);

	return 0;
}

int board_init(void)
{
	/*
	 * arch number of board
	 */
	gd->bd->bi_arch_number = CONFIG_MACH_TYPE;

	/* adress of boot parameters */
	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

	return 0;
}

#ifdef CONFIG_CMD_NET

#define MV88E1116_MAC_CTRL2_REG		21
#define MV88E1116_PGADR_REG		22
#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)

static void mv_phy_88e1118_init(char *name)
{
	u16 reg;
	u16 devadr;

	if (miiphy_set_current_dev(name))
		return;

	/* command to read PHY dev address */
	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
		printf("Err..%s could not read PHY dev address\n",
			__func__);
		return;
	}

	/*
	 * Enable RGMII delay on Tx and Rx for CPU port
	 * Ref: sec 4.7.2 of chip datasheet
	 */
	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
	miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, &reg);
	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
	miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg);
	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);

	/* reset the phy */
	miiphy_reset(name, devadr);

	printf("88E1118 Initialized on %s\n", name);
}

/* Configure and enable Switch and PHY */
void reset_phy(void)
{
	/* configure and initialize PHY */
	mv_phy_88e1118_init("egiga0");

}
#endif