blob: 54b3dfb82c5487e8e4634c2271bcd176612afefa [file] [log] [blame] [edit]
/*
* evm.c
*
* Board functions for TI814x EVM
*
* Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <cpsw.h>
#include <errno.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/io.h>
#include <asm/emif.h>
#include <asm/gpio.h>
#include "evm.h"
DECLARE_GLOBAL_DATA_PTR;
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
/* UART Defines */
#ifdef CONFIG_SPL_BUILD
static const struct cmd_control evm_ddr2_cctrl_data = {
.cmd0csratio = 0x80,
.cmd0iclkout = 0x00,
.cmd1csratio = 0x80,
.cmd1iclkout = 0x00,
.cmd2csratio = 0x80,
.cmd2iclkout = 0x00,
};
static const struct emif_regs evm_ddr2_emif0_regs = {
.sdram_config = 0x40801ab2,
.ref_ctrl = 0x10000c30,
.sdram_tim1 = 0x0aaaf552,
.sdram_tim2 = 0x043631d2,
.sdram_tim3 = 0x00000327,
.emif_ddr_phy_ctlr_1 = 0x00000007
};
static const struct emif_regs evm_ddr2_emif1_regs = {
.sdram_config = 0x40801ab2,
.ref_ctrl = 0x10000c30,
.sdram_tim1 = 0x0aaaf552,
.sdram_tim2 = 0x043631d2,
.sdram_tim3 = 0x00000327,
.emif_ddr_phy_ctlr_1 = 0x00000007
};
const struct dmm_lisa_map_regs evm_lisa_map_regs = {
.dmm_lisa_map_0 = 0x00000000,
.dmm_lisa_map_1 = 0x00000000,
.dmm_lisa_map_2 = 0x806c0300,
.dmm_lisa_map_3 = 0x806c0300,
};
static const struct ddr_data evm_ddr2_data = {
.datardsratio0 = ((0x35<<10) | (0x35<<0)),
.datawdsratio0 = ((0x20<<10) | (0x20<<0)),
.datawiratio0 = ((0<<10) | (0<<0)),
.datagiratio0 = ((0<<10) | (0<<0)),
.datafwsratio0 = ((0x90<<10) | (0x90<<0)),
.datawrsratio0 = ((0x50<<10) | (0x50<<0)),
};
void set_uart_mux_conf(void)
{
/* Set UART pins */
enable_uart0_pin_mux();
}
void set_mux_conf_regs(void)
{
/* Set MMC pins */
enable_mmc1_pin_mux();
/* Set Ethernet pins */
enable_enet_pin_mux();
}
void sdram_init(void)
{
config_dmm(&evm_lisa_map_regs);
config_ddr(0, NULL, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif0_regs, 0);
config_ddr(0, NULL, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif1_regs, 1);
}
#endif
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
return 0;
}
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
int board_mmc_init(bd_t *bis)
{
omap_mmc_init(1, 0, 0, -1, -1);
return 0;
}
#endif
#ifdef CONFIG_DRIVER_TI_CPSW
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slaves[] = {
{
.slave_reg_ofs = 0x50,
.sliver_reg_ofs = 0x700,
.phy_addr = 1,
},
{
.slave_reg_ofs = 0x90,
.sliver_reg_ofs = 0x740,
.phy_addr = 0,
},
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x100,
.slaves = 1,
.slave_data = cpsw_slaves,
.ale_reg_ofs = 0x600,
.ale_entries = 1024,
.host_port_reg_ofs = 0x28,
.hw_stats_reg_ofs = 0x400,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_1,
};
#endif
int board_eth_init(bd_t *bis)
{
uint8_t mac_addr[6];
uint32_t mac_hi, mac_lo;
if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
printf("<ethaddr> not set. Reading from E-fuse\n");
/* try reading mac address from efuse */
mac_lo = readl(&cdev->macid0l);
mac_hi = readl(&cdev->macid0h);
mac_addr[0] = mac_hi & 0xFF;
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
mac_addr[4] = mac_lo & 0xFF;
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
if (is_valid_ether_addr(mac_addr))
eth_setenv_enetaddr("ethaddr", mac_addr);
else
printf("Unable to read MAC address. Set <ethaddr>\n");
}
return cpsw_register(&cpsw_data);
}