| if ARCH_UNIPHIER |
| |
| config SYS_CONFIG_NAME |
| default "uniphier" |
| |
| config ARCH_UNIPHIER_PH1_SLD3 |
| bool "UniPhier PH1-sLD3 SoC" |
| help |
| This enables support for UniPhier PH1-sLD3 SoC. |
| |
| config ARCH_UNIPHIER_PH1_LD4 |
| bool "UniPhier PH1-LD4 SoC" |
| depends on !ARCH_UNIPHIER_PH1_SLD3 |
| help |
| This enables support for UniPhier PH1-LD4 SoC. |
| |
| config ARCH_UNIPHIER_PH1_PRO4 |
| bool "UniPhier PH1-Pro4 SoC" |
| depends on !ARCH_UNIPHIER_PH1_SLD3 && \ |
| !ARCH_UNIPHIER_PH1_LD4 && \ |
| !ARCH_UNIPHIER_PH1_SLD8 |
| help |
| This enables support for UniPhier PH1-Pro4 SoC. |
| |
| config ARCH_UNIPHIER_PH1_SLD8 |
| bool "UniPhier PH1-sLD8 SoC" |
| depends on !ARCH_UNIPHIER_PH1_SLD3 |
| help |
| This enables support for UniPhier PH1-sLD8 SoC. |
| |
| config ARCH_UNIPHIER_PH1_PRO5 |
| bool "UniPhier PH1-Pro5 SoC" |
| depends on !ARCH_UNIPHIER_PH1_SLD3 && \ |
| !ARCH_UNIPHIER_PH1_LD4 && \ |
| !ARCH_UNIPHIER_PH1_SLD8 |
| help |
| This enables support for UniPhier PH1-Pro5 SoC. |
| |
| config ARCH_UNIPHIER_PROXSTREAM2 |
| bool "UniPhier ProXstream2 SoC" |
| depends on !ARCH_UNIPHIER_PH1_SLD3 && \ |
| !ARCH_UNIPHIER_PH1_LD4 && \ |
| !ARCH_UNIPHIER_PH1_SLD8 |
| help |
| This enables support for UniPhier ProXstream2 SoC. |
| |
| config ARCH_UNIPHIER_PH1_LD6B |
| bool "UniPhier PH1-LD6b SoC" |
| depends on !ARCH_UNIPHIER_PH1_SLD3 && \ |
| !ARCH_UNIPHIER_PH1_LD4 && \ |
| !ARCH_UNIPHIER_PH1_SLD8 |
| help |
| This enables support for UniPhier PH1-LD6b SoC. |
| |
| config MICRO_SUPPORT_CARD |
| bool "Use Micro Support Card" |
| help |
| This option provides support for the expansion board, available |
| on some UniPhier reference boards. |
| |
| Say Y to use the on-board UART, Ether, LED devices. |
| |
| config CMD_PINMON |
| bool "Enable boot mode pins monitor command" |
| default y |
| help |
| The command "pinmon" shows the state of the boot mode pins. |
| The boot mode pins are latched when the system reset is deasserted |
| and determine which device the system should load a boot image from. |
| |
| config CMD_DDRPHY_DUMP |
| bool "Enable dump command of DDR PHY parameters" |
| help |
| The command "ddrphy" shows the resulting parameters of DDR PHY |
| training; it is useful for the evaluation of DDR PHY training. |
| |
| endif |
