blob: 9bb395e6a2621d317439fe5be68ebb4247874af2 [file] [log] [blame]
/*
* MPC8260 FCC Fast Ethernet
*
* Copyright (c) 2000 MontaVista Software, Inc. Dan Malek (dmalek@jlc.net)
*
* (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* MPC8260 FCC Fast Ethernet
* Basic ET HW initialization and packet RX/TX routines
*
* This code will not perform the IO port configuration. This should be
* done in the iop_conf_t structure specific for the board.
*
* TODO:
* add a PHY driver to do the negotiation
* reflect negotiation results in FPSMR
* look for ways to configure the board specific stuff elsewhere, eg.
* config_xxx.h or the board directory
*/
#include <common.h>
#include <console.h>
#include <malloc.h>
#include <asm/cpm_8260.h>
#include <mpc8260.h>
#include <command.h>
#include <config.h>
#include <net.h>
#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
#include <miiphy.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_ETHER_ON_FCC) && defined(CONFIG_CMD_NET)
static struct ether_fcc_info_s
{
int ether_index;
int proff_enet;
ulong cpm_cr_enet_sblock;
ulong cpm_cr_enet_page;
ulong cmxfcr_mask;
ulong cmxfcr_value;
}
ether_fcc_info[] =
{
#ifdef CONFIG_ETHER_ON_FCC1
{
0,
PROFF_FCC1,
CPM_CR_FCC1_SBLOCK,
CPM_CR_FCC1_PAGE,
CONFIG_SYS_CMXFCR_MASK1,
CONFIG_SYS_CMXFCR_VALUE1
},
#endif
#ifdef CONFIG_ETHER_ON_FCC2
{
1,
PROFF_FCC2,
CPM_CR_FCC2_SBLOCK,
CPM_CR_FCC2_PAGE,
CONFIG_SYS_CMXFCR_MASK2,
CONFIG_SYS_CMXFCR_VALUE2
},
#endif
#ifdef CONFIG_ETHER_ON_FCC3
{
2,
PROFF_FCC3,
CPM_CR_FCC3_SBLOCK,
CPM_CR_FCC3_PAGE,
CONFIG_SYS_CMXFCR_MASK3,
CONFIG_SYS_CMXFCR_VALUE3
},
#endif
};
/*---------------------------------------------------------------------*/
/* Maximum input DMA size. Must be a should(?) be a multiple of 4. */
#define PKT_MAXDMA_SIZE 1520
/* The FCC stores dest/src/type, data, and checksum for receive packets. */
#define PKT_MAXBUF_SIZE 1518
#define PKT_MINBUF_SIZE 64
/* Maximum input buffer size. Must be a multiple of 32. */
#define PKT_MAXBLR_SIZE 1536
#define TOUT_LOOP 1000000
#define TX_BUF_CNT 2
#ifdef __GNUC__
static char txbuf[TX_BUF_CNT][PKT_MAXBLR_SIZE] __attribute__ ((aligned(8)));
#else
#error "txbuf must be 64-bit aligned"
#endif
static uint rxIdx; /* index of the current RX buffer */
static uint txIdx; /* index of the current TX buffer */
/*
* FCC Ethernet Tx and Rx buffer descriptors.
* Provide for Double Buffering
* Note: PKTBUFSRX is defined in net.h
*/
typedef volatile struct rtxbd {
cbd_t rxbd[PKTBUFSRX];
cbd_t txbd[TX_BUF_CNT];
} RTXBD;
/* Good news: the FCC supports external BDs! */
#ifdef __GNUC__
static RTXBD rtx __attribute__ ((aligned(8)));
#else
#error "rtx must be 64-bit aligned"
#endif
static int fec_send(struct eth_device *dev, void *packet, int length)
{
int i;
int result = 0;
if (length <= 0) {
printf("fec: bad packet size: %d\n", length);
goto out;
}
for(i=0; rtx.txbd[txIdx].cbd_sc & BD_ENET_TX_READY; i++) {
if (i >= TOUT_LOOP) {
puts ("fec: tx buffer not ready\n");
goto out;
}
}
rtx.txbd[txIdx].cbd_bufaddr = (uint)packet;
rtx.txbd[txIdx].cbd_datlen = length;
rtx.txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST |
BD_ENET_TX_WRAP);
for(i=0; rtx.txbd[txIdx].cbd_sc & BD_ENET_TX_READY; i++) {
if (i >= TOUT_LOOP) {
puts ("fec: tx error\n");
goto out;
}
}
#ifdef ET_DEBUG
printf("cycles: %d status: %04x\n", i, rtx.txbd[txIdx].cbd_sc);
#endif
/* return only status bits */
result = rtx.txbd[txIdx].cbd_sc & BD_ENET_TX_STATS;
out:
return result;
}
static int fec_recv(struct eth_device* dev)
{
int length;
for (;;)
{
if (rtx.rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
length = -1;
break; /* nothing received - leave for() loop */
}
length = rtx.rxbd[rxIdx].cbd_datlen;
if (rtx.rxbd[rxIdx].cbd_sc & 0x003f) {
printf("fec: rx error %04x\n", rtx.rxbd[rxIdx].cbd_sc);
}
else {
/* Pass the packet up to the protocol layers. */
net_process_received_packet(net_rx_packets[rxIdx], length - 4);
}
/* Give the buffer back to the FCC. */
rtx.rxbd[rxIdx].cbd_datlen = 0;
/* wrap around buffer index when necessary */
if ((rxIdx + 1) >= PKTBUFSRX) {
rtx.rxbd[PKTBUFSRX - 1].cbd_sc = (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
rxIdx = 0;
}
else {
rtx.rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
rxIdx++;
}
}
return length;
}
static int fec_init(struct eth_device* dev, bd_t *bis)
{
struct ether_fcc_info_s * info = dev->priv;
int i;
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
volatile cpm8260_t *cp = &(immr->im_cpm);
fcc_enet_t *pram_ptr;
unsigned long mem_addr;
#if 0
mii_discover_phy();
#endif
/* 28.9 - (1-2): ioports have been set up already */
/* 28.9 - (3): connect FCC's tx and rx clocks */
immr->im_cpmux.cmx_uar = 0;
immr->im_cpmux.cmx_fcr = (immr->im_cpmux.cmx_fcr & ~info->cmxfcr_mask) |
info->cmxfcr_value;
/* 28.9 - (4): GFMR: disable tx/rx, CCITT CRC, Mode Ethernet */
immr->im_fcc[info->ether_index].fcc_gfmr =
FCC_GFMR_MODE_ENET | FCC_GFMR_TCRC_32;
/* 28.9 - (5): FPSMR: enable full duplex, select CCITT CRC for Ethernet */
immr->im_fcc[info->ether_index].fcc_fpsmr = CONFIG_SYS_FCC_PSMR | FCC_PSMR_ENCRC;
/* 28.9 - (6): FDSR: Ethernet Syn */
immr->im_fcc[info->ether_index].fcc_fdsr = 0xD555;
/* reset indeces to current rx/tx bd (see eth_send()/eth_rx()) */
rxIdx = 0;
txIdx = 0;
/* Setup Receiver Buffer Descriptors */
for (i = 0; i < PKTBUFSRX; i++)
{
rtx.rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
rtx.rxbd[i].cbd_datlen = 0;
rtx.rxbd[i].cbd_bufaddr = (uint)net_rx_packets[i];
}
rtx.rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
/* Setup Ethernet Transmitter Buffer Descriptors */
for (i = 0; i < TX_BUF_CNT; i++)
{
rtx.txbd[i].cbd_sc = (BD_ENET_TX_PAD | BD_ENET_TX_LAST | BD_ENET_TX_TC);
rtx.txbd[i].cbd_datlen = 0;
rtx.txbd[i].cbd_bufaddr = (uint)&txbuf[i][0];
}
rtx.txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
/* 28.9 - (7): initialise parameter ram */
pram_ptr = (fcc_enet_t *)&(immr->im_dprambase[info->proff_enet]);
/* clear whole structure to make sure all reserved fields are zero */
memset((void*)pram_ptr, 0, sizeof(fcc_enet_t));
/*
* common Parameter RAM area
*
* Allocate space in the reserved FCC area of DPRAM for the
* internal buffers. No one uses this space (yet), so we
* can do this. Later, we will add resource management for
* this area.
*/
mem_addr = CPM_FCC_SPECIAL_BASE + ((info->ether_index) * 64);
pram_ptr->fen_genfcc.fcc_riptr = mem_addr;
pram_ptr->fen_genfcc.fcc_tiptr = mem_addr+32;
/*
* Set maximum bytes per receive buffer.
* It must be a multiple of 32.
*/
pram_ptr->fen_genfcc.fcc_mrblr = PKT_MAXBLR_SIZE;
pram_ptr->fen_genfcc.fcc_rstate = (CPMFCR_GBL | CPMFCR_EB |
CONFIG_SYS_CPMFCR_RAMTYPE) << 24;
pram_ptr->fen_genfcc.fcc_rbase = (unsigned int)(&rtx.rxbd[rxIdx]);
pram_ptr->fen_genfcc.fcc_tstate = (CPMFCR_GBL | CPMFCR_EB |
CONFIG_SYS_CPMFCR_RAMTYPE) << 24;
pram_ptr->fen_genfcc.fcc_tbase = (unsigned int)(&rtx.txbd[txIdx]);
/* protocol-specific area */
pram_ptr->fen_cmask = 0xdebb20e3; /* CRC mask */
pram_ptr->fen_cpres = 0xffffffff; /* CRC preset */
pram_ptr->fen_retlim = 15; /* Retry limit threshold */
pram_ptr->fen_mflr = PKT_MAXBUF_SIZE; /* maximum frame length register */
/*
* Set Ethernet station address.
*
* This is supplied in the board information structure, so we
* copy that into the controller.
* So, far we have only been given one Ethernet address. We make
* it unique by setting a few bits in the upper byte of the
* non-static part of the address.
*/
#define ea eth_get_ethaddr()
pram_ptr->fen_paddrh = (ea[5] << 8) + ea[4];
pram_ptr->fen_paddrm = (ea[3] << 8) + ea[2];
pram_ptr->fen_paddrl = (ea[1] << 8) + ea[0];
#undef ea
pram_ptr->fen_minflr = PKT_MINBUF_SIZE; /* minimum frame length register */
/* pad pointer. use tiptr since we don't need a specific padding char */
pram_ptr->fen_padptr = pram_ptr->fen_genfcc.fcc_tiptr;
pram_ptr->fen_maxd1 = PKT_MAXDMA_SIZE; /* maximum DMA1 length */
pram_ptr->fen_maxd2 = PKT_MAXDMA_SIZE; /* maximum DMA2 length */
pram_ptr->fen_rfthr = 1;
pram_ptr->fen_rfcnt = 1;
#if 0
printf("pram_ptr->fen_genfcc.fcc_rbase %08lx\n",
pram_ptr->fen_genfcc.fcc_rbase);
printf("pram_ptr->fen_genfcc.fcc_tbase %08lx\n",
pram_ptr->fen_genfcc.fcc_tbase);
#endif
/* 28.9 - (8): clear out events in FCCE */
immr->im_fcc[info->ether_index].fcc_fcce = ~0x0;
/* 28.9 - (9): FCCM: mask all events */
immr->im_fcc[info->ether_index].fcc_fccm = 0;
/* 28.9 - (10-12): we don't use ethernet interrupts */
/* 28.9 - (13)
*
* Let's re-initialize the channel now. We have to do it later
* than the manual describes because we have just now finished
* the BD initialization.
*/
cp->cp_cpcr = mk_cr_cmd(info->cpm_cr_enet_page,
info->cpm_cr_enet_sblock,
0x0c,
CPM_CR_INIT_TRX) | CPM_CR_FLG;
do {
__asm__ __volatile__ ("eieio");
} while (cp->cp_cpcr & CPM_CR_FLG);
/* 28.9 - (14): enable tx/rx in gfmr */
immr->im_fcc[info->ether_index].fcc_gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
return 1;
}
static void fec_halt(struct eth_device* dev)
{
struct ether_fcc_info_s * info = dev->priv;
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
/* write GFMR: disable tx/rx */
immr->im_fcc[info->ether_index].fcc_gfmr &=
~(FCC_GFMR_ENT | FCC_GFMR_ENR);
}
int fec_initialize(bd_t *bis)
{
struct eth_device* dev;
int i;
for (i = 0; i < sizeof(ether_fcc_info) / sizeof(ether_fcc_info[0]); i++)
{
dev = (struct eth_device*) malloc(sizeof *dev);
memset(dev, 0, sizeof *dev);
sprintf(dev->name, "FCC%d",
ether_fcc_info[i].ether_index + 1);
dev->priv = &ether_fcc_info[i];
dev->init = fec_init;
dev->halt = fec_halt;
dev->send = fec_send;
dev->recv = fec_recv;
eth_register(dev);
#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII)) \
&& defined(CONFIG_BITBANGMII)
miiphy_register(dev->name,
bb_miiphy_read, bb_miiphy_write);
#endif
}
return 1;
}
#ifdef CONFIG_ETHER_LOOPBACK_TEST
#define ELBT_BUFSZ 1024 /* must be multiple of 32 */
#define ELBT_CRCSZ 4
#define ELBT_NRXBD 4 /* must be at least 2 */
#define ELBT_NTXBD 4
#define ELBT_MAXRXERR 32
#define ELBT_MAXTXERR 32
#define ELBT_CLSWAIT 1000 /* msec to wait for further input frames */
typedef
struct {
uint off;
char *lab;
}
elbt_prdesc;
typedef
struct {
uint _l, _f, m, bc, mc, lg, no, sh, cr, ov, cl;
uint badsrc, badtyp, badlen, badbit;
}
elbt_rxeacc;
static elbt_prdesc rxeacc_descs[] = {
{ offsetof(elbt_rxeacc, _l), "Not Last in Frame" },
{ offsetof(elbt_rxeacc, _f), "Not First in Frame" },
{ offsetof(elbt_rxeacc, m), "Address Miss" },
{ offsetof(elbt_rxeacc, bc), "Broadcast Address" },
{ offsetof(elbt_rxeacc, mc), "Multicast Address" },
{ offsetof(elbt_rxeacc, lg), "Frame Length Violation"},
{ offsetof(elbt_rxeacc, no), "Non-Octet Alignment" },
{ offsetof(elbt_rxeacc, sh), "Short Frame" },
{ offsetof(elbt_rxeacc, cr), "CRC Error" },
{ offsetof(elbt_rxeacc, ov), "Overrun" },
{ offsetof(elbt_rxeacc, cl), "Collision" },
{ offsetof(elbt_rxeacc, badsrc), "Bad Src Address" },
{ offsetof(elbt_rxeacc, badtyp), "Bad Frame Type" },
{ offsetof(elbt_rxeacc, badlen), "Bad Frame Length" },
{ offsetof(elbt_rxeacc, badbit), "Data Compare Errors" },
};
static int rxeacc_ndesc = sizeof (rxeacc_descs) / sizeof (rxeacc_descs[0]);
typedef
struct {
uint def, hb, lc, rl, rc, un, csl;
}
elbt_txeacc;
static elbt_prdesc txeacc_descs[] = {
{ offsetof(elbt_txeacc, def), "Defer Indication" },
{ offsetof(elbt_txeacc, hb), "Heartbeat" },
{ offsetof(elbt_txeacc, lc), "Late Collision" },
{ offsetof(elbt_txeacc, rl), "Retransmission Limit" },
{ offsetof(elbt_txeacc, rc), "Retry Count" },
{ offsetof(elbt_txeacc, un), "Underrun" },
{ offsetof(elbt_txeacc, csl), "Carrier Sense Lost" },
};
static int txeacc_ndesc = sizeof (txeacc_descs) / sizeof (txeacc_descs[0]);
typedef
struct {
uchar rxbufs[ELBT_NRXBD][ELBT_BUFSZ];
uchar txbufs[ELBT_NTXBD][ELBT_BUFSZ];
cbd_t rxbd[ELBT_NRXBD];
cbd_t txbd[ELBT_NTXBD];
enum { Idle, Running, Closing, Closed } state;
int proff, page, sblock;
uint clstime, nsent, ntxerr, nrcvd, nrxerr;
ushort rxerrs[ELBT_MAXRXERR], txerrs[ELBT_MAXTXERR];
elbt_rxeacc rxeacc;
elbt_txeacc txeacc;
} __attribute__ ((aligned(8)))
elbt_chan;
static uchar patbytes[ELBT_NTXBD] = {
0xff, 0xaa, 0x55, 0x00
};
static uint patwords[ELBT_NTXBD] = {
0xffffffff, 0xaaaaaaaa, 0x55555555, 0x00000000
};
#ifdef __GNUC__
static elbt_chan elbt_chans[3] __attribute__ ((aligned(8)));
#else
#error "elbt_chans must be 64-bit aligned"
#endif
#define CPM_CR_GRACEFUL_STOP_TX ((ushort)0x0005)
static elbt_prdesc epram_descs[] = {
{ offsetof(fcc_enet_t, fen_crcec), "CRC Errors" },
{ offsetof(fcc_enet_t, fen_alec), "Alignment Errors" },
{ offsetof(fcc_enet_t, fen_disfc), "Discarded Frames" },
{ offsetof(fcc_enet_t, fen_octc), "Octets" },
{ offsetof(fcc_enet_t, fen_colc), "Collisions" },
{ offsetof(fcc_enet_t, fen_broc), "Broadcast Frames" },
{ offsetof(fcc_enet_t, fen_mulc), "Multicast Frames" },
{ offsetof(fcc_enet_t, fen_uspc), "Undersize Frames" },
{ offsetof(fcc_enet_t, fen_frgc), "Fragments" },
{ offsetof(fcc_enet_t, fen_ospc), "Oversize Frames" },
{ offsetof(fcc_enet_t, fen_jbrc), "Jabbers" },
{ offsetof(fcc_enet_t, fen_p64c), "64 Octet Frames" },
{ offsetof(fcc_enet_t, fen_p65c), "65-127 Octet Frames" },
{ offsetof(fcc_enet_t, fen_p128c), "128-255 Octet Frames" },
{ offsetof(fcc_enet_t, fen_p256c), "256-511 Octet Frames" },
{ offsetof(fcc_enet_t, fen_p512c), "512-1023 Octet Frames" },
{ offsetof(fcc_enet_t, fen_p1024c), "1024-1518 Octet Frames"},
};
static int epram_ndesc = sizeof (epram_descs) / sizeof (epram_descs[0]);
/*
* given an elbt_prdesc array and an array of base addresses, print
* each prdesc down the screen with the values fetched from each
* base address across the screen
*/
static void
print_desc (elbt_prdesc descs[], int ndesc, uchar *bases[], int nbase)
{
elbt_prdesc *dp = descs, *edp = dp + ndesc;
int i;
printf ("%32s", "");
for (i = 0; i < nbase; i++)
printf (" Channel %d", i);
putc ('\n');
while (dp < edp) {
printf ("%-32s", dp->lab);
for (i = 0; i < nbase; i++) {
uint val = *(uint *)(bases[i] + dp->off);
printf (" %10u", val);
}
putc ('\n');
dp++;
}
}
/*
* return number of bits that are set in a value; value contains
* nbits (right-justified) bits.
*/
static uint __inline__
nbs (uint value, uint nbits)
{
uint cnt = 0;
#if 1
uint pos = sizeof (uint) * 8;
__asm__ __volatile__ ("\
mtctr %2\n\
1: rlwnm. %2,%1,%4,31,31\n\
beq 2f\n\
addi %0,%0,1\n\
2: subi %4,%4,1\n\
bdnz 1b"
: "=r"(cnt)
: "r"(value), "r"(nbits), "r"(cnt), "r"(pos)
: "ctr", "cc" );
#else
uint mask = 1;
do {
if (value & mask)
cnt++;
mask <<= 1;
} while (--nbits);
#endif
return (cnt);
}
static ulong
badbits (uchar *bp, int n, ulong pat)
{
ulong *lp, cnt = 0;
int nl;
while (n > 0 && ((ulong)bp & (sizeof (ulong) - 1)) != 0) {
uchar diff;
diff = *bp++ ^ (uchar)pat;
if (diff)
cnt += nbs ((ulong)diff, 8);
n--;
}
lp = (ulong *)bp;
nl = n / sizeof (ulong);
n -= nl * sizeof (ulong);
while (nl > 0) {
ulong diff;
diff = *lp++ ^ pat;
if (diff)
cnt += nbs (diff, 32);
nl--;
}
bp = (uchar *)lp;
while (n > 0) {
uchar diff;
diff = *bp++ ^ (uchar)pat;
if (diff)
cnt += nbs ((ulong)diff, 8);
n--;
}
return (cnt);
}
static inline unsigned short
swap16 (unsigned short x)
{
return (((x & 0xff) << 8) | ((x & 0xff00) >> 8));
}
/* broadcast is not an error - we send them like that */
#define BD_ENET_RX_ERRS (BD_ENET_RX_STATS & ~BD_ENET_RX_BC)
void
eth_loopback_test (void)
{
volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
volatile cpm8260_t *cp = &(immr->im_cpm);
int c, nclosed;
ulong runtime, nmsec;
uchar *bases[3];
puts ("FCC Ethernet External loopback test\n");
eth_getenv_enetaddr("ethaddr", net_ethaddr);
/*
* global initialisations for all FCC channels
*/
/* 28.9 - (1-2): ioports have been set up already */
#if defined(CONFIG_SACSng)
/*
* Attention: this is board-specific
* 1, FCC2
*/
# define FCC_START_LOOP 1
# define FCC_END_LOOP 1
/*
* Attention: this is board-specific
* - FCC2 Rx-CLK is CLK13
* - FCC2 Tx-CLK is CLK14
*/
/* 28.9 - (3): connect FCC's tx and rx clocks */
immr->im_cpmux.cmx_uar = 0;
immr->im_cpmux.cmx_fcr = CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14;
#else
#error "eth_loopback_test not supported on your board"
#endif
puts ("Initialise FCC channels:");
for (c = FCC_START_LOOP; c <= FCC_END_LOOP; c++) {
elbt_chan *ecp = &elbt_chans[c];
volatile fcc_t *fcp = &immr->im_fcc[c];
volatile fcc_enet_t *fpp;
int i;
ulong addr;
/*
* initialise channel data
*/
printf (" %d", c);
memset ((void *)ecp, 0, sizeof (*ecp));
ecp->state = Idle;
switch (c) {
case 0: /* FCC1 */
ecp->proff = PROFF_FCC1;
ecp->page = CPM_CR_FCC1_PAGE;
ecp->sblock = CPM_CR_FCC1_SBLOCK;
break;
case 1: /* FCC2 */
ecp->proff = PROFF_FCC2;
ecp->page = CPM_CR_FCC2_PAGE;
ecp->sblock = CPM_CR_FCC2_SBLOCK;
break;
case 2: /* FCC3 */
ecp->proff = PROFF_FCC3;
ecp->page = CPM_CR_FCC3_PAGE;
ecp->sblock = CPM_CR_FCC3_SBLOCK;
break;
}
/*
* set up tx buffers and bds
*/
for (i = 0; i < ELBT_NTXBD; i++) {
cbd_t *bdp = &ecp->txbd[i];
uchar *bp = &ecp->txbufs[i][0];
bdp->cbd_bufaddr = (uint)bp;
/* room for crc */
bdp->cbd_datlen = ELBT_BUFSZ - ELBT_CRCSZ;
bdp->cbd_sc = BD_ENET_TX_READY | BD_ENET_TX_PAD | \
BD_ENET_TX_LAST | BD_ENET_TX_TC;
memset((void *)bp, patbytes[i], ELBT_BUFSZ);
net_set_ether(bp, net_bcast_ethaddr, 0x8000);
}
ecp->txbd[ELBT_NTXBD - 1].cbd_sc |= BD_ENET_TX_WRAP;
/*
* set up rx buffers and bds
*/
for (i = 0; i < ELBT_NRXBD; i++) {
cbd_t *bdp = &ecp->rxbd[i];
uchar *bp = &ecp->rxbufs[i][0];
bdp->cbd_bufaddr = (uint)bp;
bdp->cbd_datlen = 0;
bdp->cbd_sc = BD_ENET_RX_EMPTY;
memset ((void *)bp, 0, ELBT_BUFSZ);
}
ecp->rxbd[ELBT_NRXBD - 1].cbd_sc |= BD_ENET_RX_WRAP;
/*
* set up the FCC channel hardware
*/
/* 28.9 - (4): GFMR: disable tx/rx, CCITT CRC, Mode Ethernet */
fcp->fcc_gfmr = FCC_GFMR_MODE_ENET | FCC_GFMR_TCRC_32;
/* 28.9 - (5): FPSMR: fd, enet CRC, Promis, RMON, Rx SHort */
fcp->fcc_fpsmr = FCC_PSMR_FDE | FCC_PSMR_LPB | \
FCC_PSMR_ENCRC | FCC_PSMR_PRO | \
FCC_PSMR_MON | FCC_PSMR_RSH;
/* 28.9 - (6): FDSR: Ethernet Syn */
fcp->fcc_fdsr = 0xD555;
/* 29.9 - (7): initialise parameter ram */
fpp = (fcc_enet_t *)&(immr->im_dprambase[ecp->proff]);
/* clear whole struct to make sure all resv fields are zero */
memset ((void *)fpp, 0, sizeof (fcc_enet_t));
/*
* common Parameter RAM area
*
* Allocate space in the reserved FCC area of DPRAM for the
* internal buffers. No one uses this space (yet), so we
* can do this. Later, we will add resource management for
* this area.
*/
addr = CPM_FCC_SPECIAL_BASE + (c * 64);
fpp->fen_genfcc.fcc_riptr = addr;
fpp->fen_genfcc.fcc_tiptr = addr + 32;
/*
* Set maximum bytes per receive buffer.
* It must be a multiple of 32.
* buffers are in 60x bus memory.
*/
fpp->fen_genfcc.fcc_mrblr = PKT_MAXBLR_SIZE;
fpp->fen_genfcc.fcc_rstate = (CPMFCR_GBL | CPMFCR_EB) << 24;
fpp->fen_genfcc.fcc_rbase = (unsigned int)(&ecp->rxbd[0]);
fpp->fen_genfcc.fcc_tstate = (CPMFCR_GBL | CPMFCR_EB) << 24;
fpp->fen_genfcc.fcc_tbase = (unsigned int)(&ecp->txbd[0]);
/* protocol-specific area */
fpp->fen_cmask = 0xdebb20e3; /* CRC mask */
fpp->fen_cpres = 0xffffffff; /* CRC preset */
fpp->fen_retlim = 15; /* Retry limit threshold */
fpp->fen_mflr = PKT_MAXBUF_SIZE;/* max frame length register */
/*
* Set Ethernet station address.
*
* This is supplied in the board information structure, so we
* copy that into the controller.
* So, far we have only been given one Ethernet address. We use
* the same address for all channels
*/
fpp->fen_paddrh = (net_ethaddr[5] << 8) + net_ethaddr[4];
fpp->fen_paddrm = (net_ethaddr[3] << 8) + net_ethaddr[2];
fpp->fen_paddrl = (net_ethaddr[1] << 8) + net_ethaddr[0];
fpp->fen_minflr = PKT_MINBUF_SIZE; /* min frame len register */
/*
* pad pointer. use tiptr since we don't need
* a specific padding char
*/
fpp->fen_padptr = fpp->fen_genfcc.fcc_tiptr;
fpp->fen_maxd1 = PKT_MAXDMA_SIZE; /* max DMA1 length */
fpp->fen_maxd2 = PKT_MAXDMA_SIZE; /* max DMA2 length */
fpp->fen_rfthr = 1;
fpp->fen_rfcnt = 1;
/* 28.9 - (8): clear out events in FCCE */
fcp->fcc_fcce = ~0x0;
/* 28.9 - (9): FCCM: mask all events */
fcp->fcc_fccm = 0;
/* 28.9 - (10-12): we don't use ethernet interrupts */
/* 28.9 - (13)
*
* Let's re-initialize the channel now. We have to do it later
* than the manual describes because we have just now finished
* the BD initialization.
*/
cp->cp_cpcr = mk_cr_cmd (ecp->page, ecp->sblock, \
0x0c, CPM_CR_INIT_TRX) | CPM_CR_FLG;
do {
__asm__ __volatile__ ("eieio");
} while (cp->cp_cpcr & CPM_CR_FLG);
}
puts (" done\nStarting test... (Ctrl-C to Finish)\n");
/*
* Note: don't want serial output from here until the end of the
* test - the delays would probably stuff things up.
*/
clear_ctrlc ();
runtime = get_timer (0);
do {
nclosed = 0;
for (c = FCC_START_LOOP; c <= FCC_END_LOOP; c++) {
volatile fcc_t *fcp = &immr->im_fcc[c];
elbt_chan *ecp = &elbt_chans[c];
int i;
switch (ecp->state) {
case Idle:
/*
* set the channel Running ...
*/
/* 28.9 - (14): enable tx/rx in gfmr */
fcp->fcc_gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
ecp->state = Running;
break;
case Running:
/*
* (while Running only) check for
* termination of the test
*/
(void)ctrlc ();
if (had_ctrlc ()) {
/*
* initiate a "graceful stop transmit"
* on the channel
*/
cp->cp_cpcr = mk_cr_cmd (ecp->page, \
ecp->sblock, 0x0c, \
CPM_CR_GRACEFUL_STOP_TX) | \
CPM_CR_FLG;
do {
__asm__ __volatile__ ("eieio");
} while (cp->cp_cpcr & CPM_CR_FLG);
ecp->clstime = get_timer (0);
ecp->state = Closing;
}
/* fall through ... */
case Closing:
/*
* (while Running or Closing) poll the channel:
* - check for any non-READY tx buffers and
* make them ready
* - check for any non-EMPTY rx buffers and
* check that they were received correctly,
* adjust counters etc, then make empty
*/
for (i = 0; i < ELBT_NTXBD; i++) {
cbd_t *bdp = &ecp->txbd[i];
ushort sc = bdp->cbd_sc;
if ((sc & BD_ENET_TX_READY) != 0)
continue;
/*
* this frame has finished
* transmitting
*/
ecp->nsent++;
if (sc & BD_ENET_TX_STATS) {
ulong n;
/*
* we had an error on
* the transmission
*/
n = ecp->ntxerr++;
if (n < ELBT_MAXTXERR)
ecp->txerrs[n] = sc;
if (sc & BD_ENET_TX_DEF)
ecp->txeacc.def++;
if (sc & BD_ENET_TX_HB)
ecp->txeacc.hb++;
if (sc & BD_ENET_TX_LC)
ecp->txeacc.lc++;
if (sc & BD_ENET_TX_RL)
ecp->txeacc.rl++;
if (sc & BD_ENET_TX_RCMASK)
ecp->txeacc.rc++;
if (sc & BD_ENET_TX_UN)
ecp->txeacc.un++;
if (sc & BD_ENET_TX_CSL)
ecp->txeacc.csl++;
bdp->cbd_sc &= \
~BD_ENET_TX_STATS;
}
if (ecp->state == Closing)
ecp->clstime = get_timer (0);
/* make it ready again */
bdp->cbd_sc |= BD_ENET_TX_READY;
}
for (i = 0; i < ELBT_NRXBD; i++) {
cbd_t *bdp = &ecp->rxbd[i];
ushort sc = bdp->cbd_sc, mask;
if ((sc & BD_ENET_RX_EMPTY) != 0)
continue;
/* we have a new frame in this buffer */
ecp->nrcvd++;
mask = BD_ENET_RX_LAST|BD_ENET_RX_FIRST;
if ((sc & mask) != mask) {
/* somethings wrong here ... */
if (!(sc & BD_ENET_RX_LAST))
ecp->rxeacc._l++;
if (!(sc & BD_ENET_RX_FIRST))
ecp->rxeacc._f++;
}
if (sc & BD_ENET_RX_ERRS) {
ulong n;
/*
* we had some sort of error
* on the frame
*/
n = ecp->nrxerr++;
if (n < ELBT_MAXRXERR)
ecp->rxerrs[n] = sc;
if (sc & BD_ENET_RX_MISS)
ecp->rxeacc.m++;
if (sc & BD_ENET_RX_BC)
ecp->rxeacc.bc++;
if (sc & BD_ENET_RX_MC)
ecp->rxeacc.mc++;
if (sc & BD_ENET_RX_LG)
ecp->rxeacc.lg++;
if (sc & BD_ENET_RX_NO)
ecp->rxeacc.no++;
if (sc & BD_ENET_RX_SH)
ecp->rxeacc.sh++;
if (sc & BD_ENET_RX_CR)
ecp->rxeacc.cr++;
if (sc & BD_ENET_RX_OV)
ecp->rxeacc.ov++;
if (sc & BD_ENET_RX_CL)
ecp->rxeacc.cl++;
bdp->cbd_sc &= \
~BD_ENET_RX_ERRS;
}
else {
ushort datlen = bdp->cbd_datlen;
struct ethernet_hdr *ehp;
ushort prot;
int ours, tb, n, nbytes;
ehp = (struct ethernet_hdr *) \
&ecp->rxbufs[i][0];
ours = memcmp (ehp->et_src, \
net_ethaddr, 6);
prot = swap16 (ehp->et_protlen);
tb = prot & 0x8000;
n = prot & 0x7fff;
nbytes = ELBT_BUFSZ -
ETHER_HDR_SIZE -
ELBT_CRCSZ;
/* check the frame is correct */
if (datlen != ELBT_BUFSZ)
ecp->rxeacc.badlen++;
else if (!ours)
ecp->rxeacc.badsrc++;
else if (!tb || n >= ELBT_NTXBD)
ecp->rxeacc.badtyp++;
else {
ulong patword = \
patwords[n];
uint nbb;
nbb = badbits(
((uchar *)&ehp) +
ETHER_HDR_SIZE,
nbytes, patword);
ecp->rxeacc.badbit += \
nbb;
}
}
if (ecp->state == Closing)
ecp->clstime = get_timer (0);
/* make it empty again */
bdp->cbd_sc |= BD_ENET_RX_EMPTY;
}
if (ecp->state != Closing)
break;
/*
* (while Closing) check to see if
* waited long enough
*/
if (get_timer (ecp->clstime) >= ELBT_CLSWAIT) {
/* write GFMR: disable tx/rx */
fcp->fcc_gfmr &= \
~(FCC_GFMR_ENT | FCC_GFMR_ENR);
ecp->state = Closed;
}
break;
case Closed:
nclosed++;
break;
}
}
} while (nclosed < (FCC_END_LOOP - FCC_START_LOOP + 1));
runtime = get_timer (runtime);
if (runtime <= ELBT_CLSWAIT) {
printf ("Whoops! somehow elapsed time (%ld) is wrong (<= %d)\n",
runtime, ELBT_CLSWAIT);
return;
}
nmsec = runtime - ELBT_CLSWAIT;
printf ("Test Finished in %ldms (plus %dms close wait period)!\n\n",
nmsec, ELBT_CLSWAIT);
/*
* now print stats
*/
for (c = FCC_START_LOOP; c <= FCC_END_LOOP; c++) {
elbt_chan *ecp = &elbt_chans[c];
uint rxpps, txpps, nerr;
rxpps = (ecp->nrcvd * 1000) / nmsec;
txpps = (ecp->nsent * 1000) / nmsec;
printf ("Channel %d: %d rcvd (%d pps, %d rxerrs), "
"%d sent (%d pps, %d txerrs)\n\n", c,
ecp->nrcvd, rxpps, ecp->nrxerr,
ecp->nsent, txpps, ecp->ntxerr);
if ((nerr = ecp->nrxerr) > 0) {
ulong i;
printf ("\tFirst %d rx errs:", nerr);
for (i = 0; i < nerr; i++)
printf (" %04x", ecp->rxerrs[i]);
putc ('\n');
}
if ((nerr = ecp->ntxerr) > 0) {
ulong i;
printf ("\tFirst %d tx errs:", nerr);
for (i = 0; i < nerr; i++)
printf (" %04x", ecp->txerrs[i]);
putc ('\n');
}
}
puts ("Receive Error Counts:\n");
for (c = FCC_START_LOOP; c <= FCC_END_LOOP; c++)
bases[c] = (uchar *)&elbt_chans[c].rxeacc;
print_desc (rxeacc_descs, rxeacc_ndesc, bases, 3);
puts ("\nTransmit Error Counts:\n");
for (c = FCC_START_LOOP; c <= FCC_END_LOOP; c++)
bases[c] = (uchar *)&elbt_chans[c].txeacc;
print_desc (txeacc_descs, txeacc_ndesc, bases, 3);
puts ("\nRMON(-like) Counters:\n");
for (c = FCC_START_LOOP; c <= FCC_END_LOOP; c++)
bases[c] = (uchar *)&immr->im_dprambase[elbt_chans[c].proff];
print_desc (epram_descs, epram_ndesc, bases, 3);
}
#endif /* CONFIG_ETHER_LOOPBACK_TEST */
#endif