| /dts-v1/; |
| /* Copyright (c) 2018-2021, The Linux Foundation. All rights reserved. |
| * |
| * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved. |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| #include "ipq5018.dtsi" |
| |
| / { |
| #address-cells = <0x2>; |
| #size-cells = <0x2>; |
| model = "Qualcomm Technologies, Inc. IPQ5018/AP-MP02.1"; |
| compatible = "qcom,ipq5018-mp02.1", "qcom,ipq5018"; |
| interrupt-parent = <&intc>; |
| |
| MP_256; |
| /delete-property/ MP_512; |
| |
| aliases { |
| sdhc1 = &sdhc_1; /* SDC1 eMMC slot */ |
| serial0 = &blsp1_uart1; |
| serial1 = &blsp1_uart2; |
| ethernet0 = "/soc/dp1"; |
| ethernet1 = "/soc/dp2"; |
| }; |
| |
| chosen { |
| bootargs = "console=ttyMSM0,115200,n8 rw init=/init"; |
| #ifdef __IPQ_MEM_PROFILE_256_MB__ |
| bootargs-append = " swiotlb=1"; |
| #else |
| bootargs-append = " swiotlb=1 coherent_pool=2M"; |
| #endif |
| stdout-path = "serial0"; |
| }; |
| |
| /* 256 MB Profile |
| * +=========+==============+========================+ |
| * | | | | |
| * | Region | Start Offset | Size | |
| * | | | | |
| * +--------+--------------+-------------------------+ |
| * | | | | |
| * | | | | |
| * | NSS | 0x40000000 | 8MB | |
| * | | | | |
| * | | | | |
| * +--------+--------------+-------------------------+ |
| * | | | | |
| * | | | | |
| * | | | | |
| * | | | | |
| * | Linux | 0x40800000 | Depends on total memory | |
| * | | | | |
| * | | | | |
| * | | | | |
| * + | | | |
| * +--------+--------------+-------------------------+ |
| * | | | | |
| * | uboot | 0x4A600000 | 4MB | |
| * | | | | |
| * +--------+--------------+-------------------------+ |
| * | SBL | 0x4AA00000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * | smem | 0x4AB00000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * | | | | |
| * | TZ | 0x4AC00000 | 4MB | |
| * | | | | |
| * +--------+--------------+-------------------------+ |
| * | | | | |
| * | | | | |
| * | | | | |
| * | Q6 | 0x4B000000 | 20MB | |
| * | code/ | | | |
| * | data | | | |
| * +--------+--------------+-------------------------+ |
| * | | | | |
| * |IPQ5018 | 0x4C400000 | 13MB | |
| * | data | | | |
| * +--------+--------------+-------------------------+ |
| * | M3 Dump| 0x4D100000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * | QDSS | 0x4D200000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * |QCN6122 | 0x4D300000 | 15MB | |
| * | data | | | |
| * +--------+--------------+-------------------------+ |
| * | M3 Dump| 0x4E200000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * | QDSS | 0x4E300000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * |QCN6122 | 0x4E400000 | 15MB | |
| * | data | | | |
| * +--------+--------------+-------------------------+ |
| * | M3 Dump| 0x4F300000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * | QDSS | 0x4F400000 | 1MB | |
| * +--------+--------------+-------------------------+ |
| * | | |
| * | Rest of the memory for Linux | |
| * | | |
| * +=================================================+ |
| */ |
| reserved-memory { |
| /delete-node/ nss@40000000; |
| |
| nss@40000000 { |
| no-map; |
| reg = <0x0 0x40000000 0x0 0x0800000>; |
| }; |
| |
| q6_mem_regions: q6_mem_regions@4B000000 { |
| no-map; |
| reg = <0x0 0x4B000000 0x0 0x4500000>; |
| }; |
| |
| q6_code_data: q6_code_data@4B000000 { |
| no-map; |
| reg = <0x0 0x4B000000 0x0 01400000>; |
| }; |
| |
| q6_ipq5018_data: q6_ipq5018_data@4C400000 { |
| no-map; |
| reg = <0x0 0x4C400000 0x0 0xD00000>; |
| }; |
| |
| m3_dump: m3_dump@4D100000 { |
| no-map; |
| reg = <0x0 0x4D100000 0x0 0x100000>; |
| }; |
| |
| q6_etr_region: q6_etr_dump@4D200000 { |
| no-map; |
| reg = <0x0 0x4D200000 0x0 0x100000>; |
| }; |
| |
| q6_qcn6122_data1: q6_qcn6122_data1@4D300000 { |
| no-map; |
| reg = <0x0 0x4D300000 0x0 0xF00000>; |
| }; |
| |
| m3_dump_qcn6122_1: m3_dump_qcn6122_1@4E200000 { |
| no-map; |
| reg = <0x0 0x4E200000 0x0 0x100000>; |
| }; |
| |
| q6_qcn6122_etr_1: q6_qcn6122_etr_1@4E300000 { |
| no-map; |
| reg = <0x0 0x4E300000 0x0 0x100000>; |
| }; |
| |
| q6_qcn6122_data2: q6_qcn6122_data2@4E400000 { |
| no-map; |
| reg = <0x0 0x4E400000 0x0 0xF00000>; |
| }; |
| |
| m3_dump_qcn6122_2: m3_dump_qcn6122_2@4F300000 { |
| no-map; |
| reg = <0x0 0x4F300000 0x0 0x100000>; |
| }; |
| |
| q6_qcn6122_etr_2: q6_qcn6122_etr_2@4F400000 { |
| no-map; |
| reg = <0x0 0x4F400000 0x0 0x100000>; |
| }; |
| }; |
| |
| soc { |
| serial@78af000 { |
| status = "ok"; |
| }; |
| |
| blsp1_uart2: serial@78b0000 { |
| pinctrl-0 = <&blsp1_uart_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| qpic_bam: dma@7984000{ |
| status = "disabled"; |
| }; |
| |
| nand: qpic-nand@79b0000 { |
| status = "disabled"; |
| }; |
| |
| spi_0: spi@78b5000 { /* BLSP1 QUP0 */ |
| pinctrl-0 = <&blsp0_spi_pins>; |
| pinctrl-names = "default"; |
| cs-select = <0>; |
| status = "ok"; |
| |
| m25p80@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0>; |
| compatible = "n25q128a11"; |
| linux,modalias = "m25p80", "n25q128a11"; |
| spi-max-frequency = <50000000>; |
| use-default-sizes; |
| }; |
| }; |
| |
| mdio0: mdio@88000 { |
| status = "ok"; |
| |
| ethernet-phy@0 { |
| reg = <7>; |
| }; |
| }; |
| |
| mdio1: mdio@90000 { |
| status = "ok"; |
| pinctrl-0 = <&mdio1_pins &phy_pins>; |
| pinctrl-names = "default"; |
| phy-reset-gpio = <&tlmm 26 0>; |
| |
| ethernet-phy@0 { |
| reg = <4>; |
| }; |
| }; |
| |
| ess-instance { |
| num_devices = <0x1>; |
| ess-switch@0x39c00000 { |
| switch_mac_mode = <0xf>; /* mac mode for uniphy instance*/ |
| cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/ |
| qcom,port_phyinfo { |
| port@0 { |
| port_id = <1>; |
| phy_address = <7>; |
| mdiobus = <&mdio0>; |
| }; |
| port@1 { |
| port_id = <2>; |
| phy_address = <0x4>; |
| mdiobus = <&mdio1>; |
| }; |
| }; |
| led_source@0 { |
| source = <0>; |
| mode = "normal"; |
| speed = "all"; |
| blink_en = "enable"; |
| active = "low"; |
| }; |
| }; |
| }; |
| |
| q6v5_wcss@CD00000 { |
| memory-region = <&q6_mem_regions>; |
| }; |
| |
| wifi0: wifi@c000000 { |
| qcom,tgt-mem-mode = <2>; |
| status = "ok"; |
| }; |
| |
| wifi2: wifi2@c000000 { |
| compatible = "qcom,cnss-qcn6122", "qcom,cnss-qcn9100"; |
| qcom,rproc = <&q6v5_wcss>; |
| status = "disabled"; |
| }; |
| |
| dp1 { |
| device_type = "network"; |
| compatible = "qcom,nss-dp"; |
| clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>; |
| clock-names = "nss-snoc-gmac-axi-clk"; |
| qcom,id = <1>; |
| reg = <0x39C00000 0x10000>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,mactype = <2>; |
| qcom,link-poll = <1>; |
| qcom,phy-mdio-addr = <7>; |
| mdio-bus = <&mdio0>; |
| local-mac-address = [000000000000]; |
| phy-mode = "sgmii"; |
| qcom,rx-page-mode = <0>; |
| }; |
| |
| dp2 { |
| device_type = "network"; |
| compatible = "qcom,nss-dp"; |
| clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>; |
| clock-names = "nss-snoc-gmac-axi-clk"; |
| qcom,id = <2>; |
| reg = <0x39D00000 0x10000>; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,mactype = <2>; |
| qcom,link-poll = <1>; |
| qcom,phy-mdio-addr = <4>; |
| mdio-bus = <&mdio1>; |
| local-mac-address = [000000000000]; |
| phy-mode = "sgmii"; |
| qcom,rx-page-mode = <0>; |
| }; |
| |
| qcom,test@0 { |
| status = "ok"; |
| }; |
| }; |
| |
| thermal-zones { |
| status = "ok"; |
| }; |
| }; |
| |
| &sdhc_1 { |
| status = "disabled"; |
| }; |
| |
| &tlmm { |
| pinctrl-0 = <&blsp0_uart_pins &phy_led_pins>; |
| pinctrl-names = "default"; |
| |
| blsp0_uart_pins: blsp0_uart_pins { |
| blsp0_uart_rx { |
| pins = "gpio28"; |
| function = "blsp0_uart1"; |
| drive-strength = <8>; |
| input-enable; |
| bias-disable; |
| bias-pull-up; |
| }; |
| blsp0_uart_tx { |
| pins = "gpio29"; |
| function = "blsp0_uart1"; |
| drive-strength = <8>; |
| bias-disable; |
| output-high; |
| bias-pull-up; |
| }; |
| }; |
| |
| blsp1_uart_pins: blsp1_uart_pins { |
| blsp1_uart_rx { |
| pins = "gpio23"; |
| function = "blsp1_uart2"; |
| drive-strength = <8>; |
| input-enable; |
| bias-disable; |
| bias-pull-up; |
| }; |
| blsp1_uart_tx { |
| pins = "gpio25"; |
| function = "blsp1_uart2"; |
| drive-strength = <8>; |
| bias-disable; |
| output-high; |
| bias-pull-up; |
| }; |
| blsp1_uart_rfr { |
| pins = "gpio24"; |
| function = "blsp1_uart2"; |
| drive-strength = <8>; |
| bias-disable; |
| output-high; |
| bias-pull-up; |
| }; |
| blsp1_uart_cts { |
| pins = "gpio26"; |
| function = "blsp1_uart2"; |
| drive-strength = <8>; |
| bias-disable; |
| input-enable; |
| bias-pull-up; |
| }; |
| }; |
| |
| blsp0_spi_pins: blsp0_spi_pins { |
| mux { |
| pins = "gpio10", "gpio11", "gpio12", "gpio13"; |
| function = "blsp0_spi"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| phy_pins: phy_pins { |
| phy_intr { |
| pins = "gpio25"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| phy_reset { |
| pins = "gpio26"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-down; |
| output-low; |
| }; |
| }; |
| |
| mdio1_pins: mdio_pinmux { |
| mux_0 { |
| pins = "gpio36"; |
| function = "mdc"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| mux_1 { |
| pins = "gpio37"; |
| function = "mdio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| }; |
| |
| phy_led_pins: phy_led_pins { |
| gephy_led_pin { |
| pins = "gpio30"; |
| function = "led0"; |
| drive-strength = <8>; |
| bias-pull-down; |
| }; |
| }; |
| |
| btss_pins: btss_pins { |
| |
| phandle = <0x1>; |
| |
| mux_0 { |
| pins = "gpio4"; |
| function = "btss0"; |
| bias-pull-down; |
| }; |
| |
| mux_1 { |
| pins = "gpio5"; |
| function = "btss1"; |
| bias-pull-down; |
| }; |
| |
| mux_2 { |
| pins = "gpio6"; |
| function = "btss2"; |
| bias-pull-down; |
| }; |
| |
| mux_3 { |
| pins = "gpio7"; |
| function = "btss3"; |
| bias-pull-down; |
| }; |
| }; |
| |
| button_pins: button_pins { |
| wps_button { |
| pins = "gpio34"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| |
| &soc { |
| gpio_keys { |
| compatible = "gpio-keys"; |
| /* pinctrl-0 = <&button_pins>; |
| pinctrl-names = "default"; */ |
| |
| button@1 { |
| /* label = "wps"; |
| linux,code = <KEY_WPS_BUTTON>; */ |
| gpios = <&tlmm 34 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| debounce-interval = <60>; |
| }; |
| }; |
| }; |
| |
| &usb3 { |
| status = "ok"; |
| }; |
| |
| &pcie_x2 { |
| status = "disabled"; |
| perst-gpio = <&tlmm 15 1>; |
| }; |
| |
| &dwc_0 { |
| /delete-property/ #phy-cells; |
| /delete-property/ phys; |
| /delete-property/ phy-names; |
| }; |
| |
| &hs_m31phy_0 { |
| status = "ok"; |
| }; |
| |
| &pcie_x2phy { |
| status = "disabled"; |
| }; |
| |
| &pcie_x2_rp { |
| status = "disabled"; |
| |
| mhi_1: qcom,mhi@1 { |
| reg = <0 0 0 0 0 >; |
| }; |
| }; |
| |
| &q6v5_wcss { |
| qcom,multipd_arch; |
| qcom,share_bootargs; |
| qcom,bootargs_smem = <507>; |
| boot-args = <0x1 0x4 0x3 0x0F 0x0 0x0>, |
| <0x2 0x4 0x2 0x1B 0x0 0x0>; |
| |
| /* IPQ5018 */ |
| q6v5_wcss_userpd1 { |
| m3_firmware = "IPQ5018/m3_fw.mdt"; |
| interrupts-extended = <&wcss_smp2p_in 8 0>, |
| <&wcss_smp2p_in 9 0>, |
| <&wcss_smp2p_in 12 0>, |
| <&wcss_smp2p_in 11 0>; |
| interrupt-names ="fatal", |
| "ready", |
| "spawn_ack", |
| "stop-ack"; |
| qcom,smem-states = <&wcss_smp2p_out 8>, |
| <&wcss_smp2p_out 9>, |
| <&wcss_smp2p_out 10>; |
| qcom,smem-state-names = "shutdown", |
| "stop", |
| "spawn"; |
| qca,asid = <1>; |
| qca,auto-restart; |
| qca,int_radio; |
| memory-region = <&q6_ipq5018_data>, <&m3_dump>, |
| <&q6_etr_region>; |
| }; |
| |
| /* QCN6122 6G */ |
| q6v5_wcss_userpd2 { |
| m3_firmware = "qcn6122/m3_fw.mdt"; |
| interrupts-extended = <&wcss_smp2p_in 16 0>, |
| <&wcss_smp2p_in 17 0>, |
| <&wcss_smp2p_in 20 0>, |
| <&wcss_smp2p_in 19 0>; |
| interrupt-names ="fatal", |
| "ready", |
| "spawn_ack", |
| "stop-ack"; |
| qcom,smem-states = <&wcss_smp2p_out 16>, |
| <&wcss_smp2p_out 17>, |
| <&wcss_smp2p_out 18>; |
| qcom,smem-state-names = "shutdown", |
| "stop", |
| "spawn"; |
| qca,asid = <2>; |
| qca,auto-restart; |
| memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>, |
| <&q6_qcn6122_etr_1>; |
| }; |
| |
| /* QCN6122 5G */ |
| q6v5_wcss_userpd3 { |
| m3_firmware = "qcn6122/m3_fw.mdt"; |
| interrupts-extended = <&wcss_smp2p_in 24 0>, |
| <&wcss_smp2p_in 25 0>, |
| <&wcss_smp2p_in 28 0>, |
| <&wcss_smp2p_in 27 0>; |
| interrupt-names ="fatal", |
| "ready", |
| "spawn_ack", |
| "stop-ack"; |
| qcom,smem-states = <&wcss_smp2p_out 24>, |
| <&wcss_smp2p_out 25>, |
| <&wcss_smp2p_out 26>; |
| qcom,smem-state-names = "shutdown", |
| "stop", |
| "spawn"; |
| qca,asid = <3>; |
| qca,auto-restart; |
| memory-region = <&q6_qcn6122_data2>, <&m3_dump_qcn6122_2>, |
| <&q6_qcn6122_etr_2>; |
| }; |
| }; |
| |
| &wifi0 { |
| /* IPQ5018 */ |
| qcom,multipd_arch; |
| qcom,board_id = <0x10>; |
| qcom,bdf-addr = <0 0 0x4C400000 0 0>; |
| qcom,caldb-addr = <0 0 0 0 0>; |
| qcom,caldb-size = <0x0>; |
| qcom,userpd-subsys-name = "q6v5_wcss_userpd1"; |
| status = "ok"; |
| }; |
| |
| &wifi1 { |
| /* QCN6122 6G */ |
| qcom,multipd_arch; |
| qcom,board_id = <0x90>; |
| qcom,tgt-mem-mode = <2>; |
| /* |
| * once wifi driver changes are in place to |
| * qcn6122 compatible string, remove qcn9100 here |
| */ |
| compatible = "qcom,cnss-qcn6122", "qcom,cnss-qcn9100"; |
| qcom,bdf-addr = <0 0 0x4D300000 0 0>; |
| qcom,caldb-addr = <0 0 0 0 0>; |
| qcom,caldb-size = <0x0>; |
| qcom,userpd-subsys-name = "q6v5_wcss_userpd2"; |
| status = "ok"; |
| }; |
| |
| &wifi2 { |
| /* QCN6122 5G */ |
| qcom,multipd_arch; |
| qcom,board_id = <0x50>; |
| qcom,tgt-mem-mode = <2>; |
| /* |
| * once wifi driver changes are in place to |
| * qcn6122 compatible string, remove qcn9100 here |
| */ |
| compatible = "qcom,cnss-qcn6122", "qcom,cnss-qcn9100"; |
| qcom,bdf-addr = <0 0 0x4E400000 0 0>; |
| qcom,caldb-addr = <0 0 0 0 0>; |
| qcom,caldb-size = <0x0>; |
| qcom,userpd-subsys-name = "q6v5_wcss_userpd3"; |
| status = "ok"; |
| }; |
