blob: d02615bdc0d6a656568b454ec2aad02fb8a0c1cf [file] [log] [blame]
/*
* board/amlogic/configs/sm1_elaine_p0.h
*
* Copyright (C) 2015 Amlogic, Inc. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
*/
#ifndef __SM1_ELAINE_P0_H__
#define __SM1_ELAINE_P0_H__
#include <asm/arch/cpu.h>
//#define CONFIG_SYS_GENERIC_BOARD 1
/*
#ifndef CONFIG_AML_MESON
#warning "include warning"
#endif
*/
//#define CONFIG_ZIRCON_BOOT_IMAGE
/*
* platform power init config
*/
#define AML_VCCK_INIT_VOLTAGE 800 // VCCK power up voltage
#define AML_VDDEE_INIT_VOLTAGE 840 // VDDEE power up voltage
#define AML_VDDEE_SLEEP_VOLTAGE 731 // VDDEE suspend voltage
/* SMP Definitinos */
#define CPU_RELEASE_ADDR secondary_boot_func
/* Bootloader Control Block function
That is used for recovery and the bootloader to talk to each other
*/
/* Serial config */
#define CONFIG_CONS_INDEX 2
#define CONFIG_BAUDRATE 115200
/* #define CONFIG_AML_MESON_SERIAL 1 */
/* Enable ir remote wake up for bl30 */
#define AML_IR_REMOTE_POWER_UP_KEY_VAL1 0xef10fe01 //amlogic tv ir --- power
#define AML_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+
#define AML_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch-
#define AML_IR_REMOTE_POWER_UP_KEY_VAL4 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL5 0xe51afb04
#define AML_IR_REMOTE_POWER_UP_KEY_VAL6 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL7 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL8 0xFFFFFFFF
#define AML_IR_REMOTE_POWER_UP_KEY_VAL9 0xFFFFFFFF
/*config the default parameters for adc power key*/
#define AML_ADC_POWER_KEY_CHAN 2 /*channel range: 0-7*/
#define AML_ADC_POWER_KEY_VAL 0 /*sample value range: 0-1023*/
/* args/envs */
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=1080000\0" \
"outputmode=panel\0" \
"hdmimode=1080p60hz\0" \
"display_width=1920\0" \
"display_height=1080\0" \
"display_bpp=16\0" \
"display_color_index=16\0" \
"display_layer=osd0\0" \
"display_color_fg=0xffff\0" \
"display_color_bg=0\0" \
"dtb_mem_addr=0x1000000\0" \
"fb_addr=0x5f800000\0" \
"fb_width=608\0" \
"fb_height=1024\0" \
"usb_burning=update 1000\0" \
"fdt_high=0x20000000\0" \
"try_auto_burn=update 700 750;\0" \
"sdcburncfg=aml_sdc_burn.ini\0" \
"sdc_burning=sdc_burn ${sdcburncfg}\0" \
"wipe_data=successful\0" \
"wipe_cache=successful\0" \
"EnableSelinux=enforcing\0" \
"recovery_part=recovery\0" \
"recovery_offset=0\0" \
"active_slot=_a\0" \
"boot_part=boot\0" \
"ext4_factory=1:4\0" \
"storeargs=" \
"get_rebootmode;" \
"setenv bootargs " \
"gpt " \
"logo=${display_layer},loaded,${fb_addr} " \
"vout=${outputmode},enable " \
"panel_type=${panel_type} " \
"androidboot.selinux=${EnableSelinux} " \
"test_mode=${test_mode} " \
"androidboot.hardware="__stringify(BOARD_NAME)" " \
"hw_id=${hw_id} " \
"androidboot.reboot_mode=${reboot_mode} " \
"androidboot.slot_suffix=${active_slot};" \
"\0" \
"switch_bootmode=" \
"get_rebootmode;" \
"echo reboot_mode:${reboot_mode};"\
"if test ${reboot_mode} = factory_reset; then " \
"run recovery_from_flash;" \
"else if test ${reboot_mode} = update; then " \
"run update;" \
"else if test ${reboot_mode} = cold_boot; then " \
"echo cold_boot; " \
"else if test ${reboot_mode} = fastboot; then " \
"fastboot;" \
"else if test ${reboot_mode} = factory_boot; then " \
"ddr_auto_fast_boot_check 6 ;"\
"if imgread kernel fct ${loadaddr}; then " \
"bootm ${loadaddr};" \
"fi;" \
"fi;fi;fi;fi;fi;" \
"\0" \
"storeboot=" \
"ddr_auto_fast_boot_check 6 ;"\
"if imgread kernel ${boot_part} ${loadaddr}; then " \
"bootm ${loadaddr};" \
"fi;" \
"run update;" \
"\0" \
"factory_reset_poweroff_protect=" \
"echo wipe_data=${wipe_data};" \
"echo wipe_cache=${wipe_cache};" \
"if test ${wipe_data} = failed; then " \
"run init_display;" \
"run get_hw_id;" \
"run storeargs;" \
"if usb start 0; then " \
"run recovery_from_udisk;" \
"fi;" \
"run recovery_from_flash;" \
"fi;" \
"if test ${wipe_cache} = failed; then " \
"run init_display;" \
"run get_hw_id;" \
"run storeargs;" \
"if usb start 0; then " \
"run recovery_from_udisk;" \
"fi;" \
"run recovery_from_flash;" \
"fi;" \
"\0" \
"update=" \
"run usb_burning;" \
"run recovery_from_flash;" \
"\0" \
"recovery_from_udisk=" \
"while true ;do " \
"usb reset; " \
"if fatload usb 0 ${loadaddr} recovery.img; then "\
"bootm ${loadaddr};" \
"fi;" \
"done;" \
"\0" \
"recovery_from_flash=" \
"setenv bootargs ${bootargs} " \
"aml_dt=${aml_dt} " \
"recovery_part=${recovery_part} " \
"recovery_offset=${recovery_offset};" \
"if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then " \
"wipeisb;" \
"bootm ${loadaddr};" \
"fi" \
"\0" \
"reset_ddic=" \
"gpio clear GPIOH_6" \
"\0" \
"detect_panel=" \
"get_ddictype;" \
"if test $ddic_type = FITI; then " \
"if gpio input GPIOH_5; then " \
"setenv panel_type lcd_3;" \
"else " \
"setenv panel_type lcd_4;" \
"fi;" \
"else " \
"if gpio input GPIOH_5; then " \
"setenv panel_type lcd_1;" \
"else " \
"setenv panel_type lcd_2;" \
"fi;" \
"fi;" \
"\0" \
"set_gamma="\
"if ext4load mmc ${ext4_factory} 0x8000000 gamma_calibration.txt; then " \
"configure_gamma 0x8000000;" \
"else " \
"configure_gamma;" \
"fi;" \
"\0" \
"start_backlight=" \
"if ext4load mmc ${ext4_factory} 0x8000000 bl_calibration.txt; then " \
"configure_backlight 0x8000000;" \
"else " \
"configure_backlight;" \
"fi;" \
"\0" \
"init_display=" \
"run reset_ddic;" \
"check_fdr_for_backlight_brightness;" \
"osd open;" \
"osd clear;" \
"osd setcolor 0x5b0d5b0d;" \
"get_rebootmode;"\
/* logo must not fail */ \
"ext4load mmc ${ext4_factory} 0x8000000 logo.bmp;" \
"bmp display 0x8000000;" \
/* do this sequentially so we could reuse the address and do
* not need to know the size of the images */ \
"if ext4load mmc ${ext4_system} 0x8000000 corner_BL.bmp; then " \
"bmp display 0x8000000 0 1264;" \
"fi;" \
"if ext4load mmc ${ext4_system} 0x8000000 corner_BR.bmp; then " \
"bmp display 0x8000000 784 1264;" \
"fi;" \
"if ext4load mmc ${ext4_system} 0x8000000 corner_TL.bmp; then " \
"bmp display 0x8000000 0 0;" \
"fi;" \
"if ext4load mmc ${ext4_system} 0x8000000 corner_TR.bmp; then " \
"bmp display 0x8000000 784 0;" \
"fi;" \
"bmp scale;" \
"vout output ${outputmode};" \
"run set_gamma;" \
"run start_backlight;" \
"\0" \
"get_hw_id=" \
"get_elaine_hw_id;" \
"\0" \
"upgrade_key=" \
"if gpio input GPIOZ_5; then " \
"echo detect VOL_UP pressed;" \
"if gpio input GPIOZ_6; then " \
"echo VOL_DN pressed;" \
"setenv boot_external_image 1;" \
"run recovery_from_udisk;" \
"fi;" \
"else " \
"echo upgrade key not pressed;" \
"setenv boot_external_image 0;" \
"fi;" \
"\0" \
"test_mode_check=" \
"setenv test_mode false;" \
"if gpio input GPIOZ_2; then " \
"echo MUTE not engaged;" \
"else " \
"echo MUTE engaged;" \
"if gpio input GPIOZ_5; then " \
"echo VOL_UP pressed;" \
"if gpio input GPIOZ_6; then " \
"echo VOL_DN pressed;" \
"else " \
"echo VOL_DN not pressed;" \
"setenv test_mode true;" \
"fi;" \
"else " \
"echo VOL_UP not pressed;" \
"fi;" \
"fi;" \
"\0" \
#define CONFIG_PREBOOT \
"run factory_reset_poweroff_protect;" \
"run init_display;" \
"run get_hw_id;" \
"run test_mode_check;" \
"run storeargs;" \
"run upgrade_key;" \
"run switch_bootmode;"
/* #define CONFIG_ENV_IS_NOWHERE 1 */
#define CONFIG_ENV_SIZE (64*1024)
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_ANDROID_BOOT_IMAGE 1
#define CONFIG_SYS_BOOTM_LEN (64<<20) /* Increase max gunzip size*/
/* cpu */
/* #define CONFIG_CPU_CLK 1200 //MHz. Range: 360-2000, should be multiple of 24 */
/* ATTENTION */
/* DDR configs move to board/amlogic/[board]/firmware/timing.c */
//#define CONFIG_NR_DRAM_BANKS 1
/* ddr functions */
#define DDR_FULL_TEST 0 //0:disable, 1:enable. ddr full test
#define DDR_LOW_POWER 0 //0:disable, 1:enable. ddr clk gate for lp
#define DDR_ZQ_PD 0 //0:disable, 1:enable. ddr zq power down
#define DDR_USE_EXT_VREF 0 //0:disable, 1:enable. ddr use external vref
#define DDR4_TIMING_TEST 0 //0:disable, 1:enable. ddr4 timing test function
#define DDR_PLL_BYPASS 0 //0:disable, 1:enable. ddr pll bypass function
/* storage: emmc/nand/sd */
#define CONFIG_ENV_OVERWRITE
/* #define CONFIG_CMD_SAVEENV */
/* fixme, need fix*/
#if (defined(CONFIG_ENV_IS_IN_AMLNAND) || defined(CONFIG_ENV_IS_IN_MMC)) && defined(CONFIG_STORE_COMPATIBLE)
#error env in amlnand/mmc already be compatible;
#endif
/*
* storage
* |---------|---------|
* | |
* emmc<--Compatible-->nand
* |-------|-------|
* | |
* MTD<-Exclusive->NFTL
*/
/* axg only support slc nand */
/* swither for mtd nand which is for slc only. */
/* support for mtd */
/* #define CONFIG_AML_MTD 1 */
/* support for nftl */
/*#define CONFIG_AML_NAND 1*/
#if defined(CONFIG_AML_NAND) && defined(CONFIG_AML_MTD)
#error CONFIG_AML_NAND/CONFIG_AML_MTD can not support at the sametime;
#endif
#ifdef CONFIG_AML_MTD
/* bootlaoder is construct by bl2 and fip
* when DISCRETE_BOOTLOADER is enabled, bl2 & fip
* will not be stored continuously, and nand layout
* would be bl2|rsv|fip|normal, but not
* bl2|fip|rsv|noraml anymore
*/
/* #define CONFIG_CMD_NAND 1 */
#define CONFIG_MTD_DEVICE y
/* mtd parts of ourown.*/
#define CONFIG_AML_MTDPART 1
/* mtd parts by env default way.*/
/*
#define MTDIDS_NAME_STR "aml_nand.0"
#define MTDIDS_DEFAULT "nand1=" MTDIDS_NAME_STR
#define MTDPARTS_DEFAULT "mtdparts=" MTDIDS_NAME_STR ":" \
"3M@8192K(logo)," \
"10M(recovery)," \
"8M(kernel)," \
"40M(rootfs)," \
"-(data)"
*/
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_MTD_UBI_WL_THRESHOLD 4096
#define CONFIG_MTD_UBI_BEB_LIMIT 20
#define CONFIG_RBTREE
#define CONFIG_CMD_NAND_TORTURE 1
#define CONFIG_CMD_MTDPARTS 1
#define CONFIG_MTD_PARTITIONS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 2
#define CONFIG_SYS_NAND_BASE_LIST {0}
#endif
/* endof CONFIG_AML_MTD */
/* #define CONFIG_AML_SD_EMMC 1 */
#ifdef CONFIG_AML_SD_EMMC
#define CONFIG_GENERIC_MMC 1
#define CONFIG_CMD_MMC 1
#define CONFIG_CMD_GPT 1
#define CONFIG_SYS_MMC_ENV_DEV 1
#define CONFIG_EMMC_DDR52_EN 0
#define CONFIG_EMMC_DDR52_CLK 35000000
#endif
#define CONFIG_PARTITIONS 1
#if defined CONFIG_AML_MTD || defined CONFIG_SPI_NAND
#define CONFIG_CMD_NAND 1
#define CONFIG_MTD_DEVICE y
/* #define CONFIG_RBTREE */
#define CONFIG_CMD_NAND_TORTURE 1
#define CONFIG_CMD_MTDPARTS 1
#define CONFIG_MTD_PARTITIONS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 2
#define CONFIG_SYS_NAND_BASE_LIST {0}
#endif
/* vpu */
#define AML_VPU_CLK_LEVEL_DFT 7
/* osd */
#define OSD_SCALE_ENABLE
#define AML_OSD_HIGH_VERSION
/* USB
* Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
* Enable CONFIG_MUSB_UDD for Device functionalities.
*/
/* #define CONFIG_MUSB_UDC 1 */
/* #define CONFIG_CMD_USB 1 */
#define AML_TXLX_USB 1
#define USB_PHY2_PLL_PARAMETER_1 0x09400414
#define USB_PHY2_PLL_PARAMETER_2 0x927e0000
#define USB_PHY2_PLL_PARAMETER_3 0xAC5F69E5
#define USB_G12x_PHY_PLL_SETTING_1 (0xfe18)
#define USB_G12x_PHY_PLL_SETTING_2 (0xfff)
#define USB_G12x_PHY_PLL_SETTING_3 (0x78000)
#define USB_G12x_PHY_PLL_SETTING_4 (0xe0004)
#define USB_G12x_PHY_PLL_SETTING_5 (0xe000c)
/* UBOOT Facotry usb/sdcard burning config */
#ifndef AML_DISABLE_UPDATE_MODE
#define CONFIG_AML_V2_FACTORY_BURN 1 //support facotry usb burning
#define CONFIG_USB_BURNING_TOOL 1
#define CONFIG_AML_FACTORY_BURN_LOCAL_UPGRADE 1 //support factory sdcard burning
#define CONFIG_SD_BURNING_SUPPORT_UI 1 //Displaying upgrading progress bar when sdcard/udisk burning
#endif
/* net */
#if defined(CONFIG_CMD_NET)
#define CONFIG_DESIGNWARE_ETH 1
#define CONFIG_PHYLIB 1
#define CONFIG_NET_MULTI 1
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
#define CONFIG_CMD_RARP 1
#define CONFIG_HOSTNAME "arm_gxbb"
#define CONFIG_ETHADDR 00:15:18:01:81:31 /* Ethernet address */
#define CONFIG_IPADDR 10.18.9.97 /* Our ip address */
#define CONFIG_GATEWAYIP 10.18.9.1 /* Our getway ip address */
#define CONFIG_SERVERIP 10.18.9.113 /* Tftp server ip address */
#define CONFIG_NETMASK 255.255.255.0
#endif /* (CONFIG_CMD_NET) */
/* other devices */
#define CONFIG_SHA1 1
#define CONFIG_MD5 1
/* commands */
/* #define CONFIG_CMD_FDT 1 */
/*file system*/
#define CONFIG_DOS_PARTITION 1
#define CONFIG_EFI_PARTITION 1
/* #define CONFIG_MMC 1 */
#define CONFIG_LZO 1
/* Cache Definitions */
/* #define CONFIG_SYS_DCACHE_OFF */
/* #define CONFIG_SYS_ICACHE_OFF */
/* other functions */
#define CONFIG_FIP_IMG_SUPPORT 1
/* #define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 */ /* hide 128MB for kernel reserve */
#define CONFIG_CPU_ARMV8
/* #define CONFIG_MULTI_DTB 1 */
#define DTB_BIND_KERNEL 1
/* support secure boot */
#define CONFIG_AML_SECURE_UBOOT 1
#if defined(CONFIG_AML_SECURE_UBOOT)
/* for SRAM size limitation just disable NAND
as the socket board default has no NAND */
/* #undef CONFIG_AML_NAND */
/* unify build for generate encrypted bootloader "u-boot.bin.encrypt" */
#define CONFIG_AML_CRYPTO_UBOOT 1
/* unify build for generate encrypted kernel image
SRC : "board/amlogic/(board)/boot.img"
DST : "fip/boot.img.encrypt" */
/* #define CONFIG_AML_CRYPTO_IMG 1 */
#endif /* CONFIG_AML_SECURE_UBOOT */
/* build with uboot auto test */
/* #define CONFIG_AML_UBOOT_AUTO_TEST 1 */
/* board customer ID */
/* #define CONFIG_CUSTOMER_ID (0x6472616F624C4D41) */
/* Choose One of Ethernet Type */
#undef CONFIG_ETHERNET_NONE
#define ETHERNET_INTERNAL_PHY
#undef ETHERNET_EXTERNAL_PHY
#if defined(CONFIG_CMD_AML_MTEST)
#if !defined(CONFIG_SYS_MEM_TOP_HIDE)
#error CONFIG_CMD_AML_MTEST depends on CONFIG_SYS_MEM_TOP_HIDE;
#endif
#if !(CONFIG_SYS_MEM_TOP_HIDE)
#error CONFIG_SYS_MEM_TOP_HIDE should not be zero;
#endif
#endif
#endif