blob: d73752c7f956b50d5380bb6b21108e223b41fea6 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
*/
#ifndef _CONFIG_SBX81LIFXCAT_H
#define _CONFIG_SBX81LIFXCAT_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
#define CONFIG_BUILD_TARGET "u-boot.kwb"
/* additions for new ARM relocation support */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
#define CONFIG_KIRKWOOD_GPIO 1
/*
* NS16550 Configuration
*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
/*
* Serial Port configuration
* The following definitions let you select what serial you want to use
* for your console driver.
*/
#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
#define MTDPARTS_MTDOOPS "errlog"
#define CONFIG_DOS_PARTITION
/*
* Environment variables configurations
*/
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
#define CONFIG_ENV_SIZE 0x02000
#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here - 768K */
/*
* U-Boot bootcode configuration
*/
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
/* size in bytes reserved for initial data */
#include <asm/arch/config.h>
/* There is no PHY directly connected so don't ask it for link status */
#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
/*
* Other required minimal configurations
*/
#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_NET_MULTI /* specify more that one ports available */
#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
#define CONFIG_PHY_BASE_ADR 0x01
#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
#endif /* CONFIG_CMD_NET */
#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
#endif /* _CONFIG_SBX81LIFXCAT_H */