/** | |
****************************************************************************** | |
* @file misc.c | |
* @author MCD Application Team | |
* @version V1.0.0 | |
* @date 30-September-2011 | |
* @brief This file provides all the miscellaneous firmware functions (add-on | |
* to CMSIS functions). | |
* | |
* @verbatim | |
* | |
* =================================================================== | |
* How to configure Interrupts using driver | |
* =================================================================== | |
* | |
* This section provide functions allowing to configure the NVIC interrupts (IRQ). | |
* The Cortex-M4 exceptions are managed by CMSIS functions. | |
* | |
* 1. Configure the NVIC Priority Grouping using NVIC_PriorityGroupConfig() | |
* function according to the following table. | |
* The table below gives the allowed values of the pre-emption priority and subpriority according | |
* to the Priority Grouping configuration performed by NVIC_PriorityGroupConfig function | |
* ========================================================================================================================== | |
* NVIC_PriorityGroup | NVIC_IRQChannelPreemptionPriority | NVIC_IRQChannelSubPriority | Description | |
* ========================================================================================================================== | |
* NVIC_PriorityGroup_0 | 0 | 0-15 | 0 bits for pre-emption priority | |
* | | | 4 bits for subpriority | |
* -------------------------------------------------------------------------------------------------------------------------- | |
* NVIC_PriorityGroup_1 | 0-1 | 0-7 | 1 bits for pre-emption priority | |
* | | | 3 bits for subpriority | |
* -------------------------------------------------------------------------------------------------------------------------- | |
* NVIC_PriorityGroup_2 | 0-3 | 0-3 | 2 bits for pre-emption priority | |
* | | | 2 bits for subpriority | |
* -------------------------------------------------------------------------------------------------------------------------- | |
* NVIC_PriorityGroup_3 | 0-7 | 0-1 | 3 bits for pre-emption priority | |
* | | | 1 bits for subpriority | |
* -------------------------------------------------------------------------------------------------------------------------- | |
* NVIC_PriorityGroup_4 | 0-15 | 0 | 4 bits for pre-emption priority | |
* | | | 0 bits for subpriority | |
* ========================================================================================================================== | |
* | |
* 2. Enable and Configure the priority of the selected IRQ Channels using NVIC_Init() | |
* | |
* @note When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. | |
* The pending IRQ priority will be managed only by the subpriority. | |
* | |
* @note IRQ priority order (sorted by highest to lowest priority): | |
* - Lowest pre-emption priority | |
* - Lowest subpriority | |
* - Lowest hardware priority (IRQ number) | |
* | |
* @endverbatim | |
* | |
****************************************************************************** | |
* @attention | |
* | |
* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS | |
* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE | |
* TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY | |
* DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING | |
* FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE | |
* CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. | |
* | |
* <h2><center>© COPYRIGHT 2011 STMicroelectronics</center></h2> | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "misc.h" | |
/** @addtogroup STM32F4xx_StdPeriph_Driver | |
* @{ | |
*/ | |
/** @defgroup MISC | |
* @brief MISC driver modules | |
* @{ | |
*/ | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
#define AIRCR_VECTKEY_MASK ((uint32_t)0x05FA0000) | |
/* Private macro -------------------------------------------------------------*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/* Private functions ---------------------------------------------------------*/ | |
/** @defgroup MISC_Private_Functions | |
* @{ | |
*/ | |
/** | |
* @brief Configures the priority grouping: pre-emption priority and subpriority. | |
* @param NVIC_PriorityGroup: specifies the priority grouping bits length. | |
* This parameter can be one of the following values: | |
* @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority | |
* 4 bits for subpriority | |
* @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority | |
* 3 bits for subpriority | |
* @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority | |
* 2 bits for subpriority | |
* @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority | |
* 1 bits for subpriority | |
* @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority | |
* 0 bits for subpriority | |
* @note When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. | |
* The pending IRQ priority will be managed only by the subpriority. | |
* @retval None | |
*/ | |
void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup)); | |
/* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */ | |
SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup; | |
} | |
/** | |
* @brief Initializes the NVIC peripheral according to the specified | |
* parameters in the NVIC_InitStruct. | |
* @note To configure interrupts priority correctly, the NVIC_PriorityGroupConfig() | |
* function should be called before. | |
* @param NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains | |
* the configuration information for the specified NVIC peripheral. | |
* @retval None | |
*/ | |
void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct) | |
{ | |
uint8_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F; | |
/* Check the parameters */ | |
assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd)); | |
assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority)); | |
assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority)); | |
if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE) | |
{ | |
/* Compute the Corresponding IRQ Priority --------------------------------*/ | |
tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08; | |
tmppre = (0x4 - tmppriority); | |
tmpsub = tmpsub >> tmppriority; | |
tmppriority = NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre; | |
tmppriority |= (uint8_t)(NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub); | |
tmppriority = tmppriority << 0x04; | |
NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority; | |
/* Enable the Selected IRQ Channels --------------------------------------*/ | |
NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] = | |
(uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F); | |
} | |
else | |
{ | |
/* Disable the Selected IRQ Channels -------------------------------------*/ | |
NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] = | |
(uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F); | |
} | |
} | |
/** | |
* @brief Sets the vector table location and Offset. | |
* @param NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory. | |
* This parameter can be one of the following values: | |
* @arg NVIC_VectTab_RAM: Vector Table in internal SRAM. | |
* @arg NVIC_VectTab_FLASH: Vector Table in internal FLASH. | |
* @param Offset: Vector Table base offset field. This value must be a multiple of 0x200. | |
* @retval None | |
*/ | |
void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_NVIC_VECTTAB(NVIC_VectTab)); | |
assert_param(IS_NVIC_OFFSET(Offset)); | |
SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80); | |
} | |
/** | |
* @brief Selects the condition for the system to enter low power mode. | |
* @param LowPowerMode: Specifies the new mode for the system to enter low power mode. | |
* This parameter can be one of the following values: | |
* @arg NVIC_LP_SEVONPEND: Low Power SEV on Pend. | |
* @arg NVIC_LP_SLEEPDEEP: Low Power DEEPSLEEP request. | |
* @arg NVIC_LP_SLEEPONEXIT: Low Power Sleep on Exit. | |
* @param NewState: new state of LP condition. This parameter can be: ENABLE or DISABLE. | |
* @retval None | |
*/ | |
void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_NVIC_LP(LowPowerMode)); | |
assert_param(IS_FUNCTIONAL_STATE(NewState)); | |
if (NewState != DISABLE) | |
{ | |
SCB->SCR |= LowPowerMode; | |
} | |
else | |
{ | |
SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode); | |
} | |
} | |
/** | |
* @brief Configures the SysTick clock source. | |
* @param SysTick_CLKSource: specifies the SysTick clock source. | |
* This parameter can be one of the following values: | |
* @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source. | |
* @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source. | |
* @retval None | |
*/ | |
void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource)); | |
if (SysTick_CLKSource == SysTick_CLKSource_HCLK) | |
{ | |
SysTick->CTRL |= SysTick_CLKSource_HCLK; | |
} | |
else | |
{ | |
SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ |