blob: f09345f97017b18aa0fa635026a103cd57c5e81e [file] [log] [blame]
/*******************************************************************************
* Trace Recorder Library for Tracealyzer v3.1.2
* Percepio AB, www.percepio.com
*
* trcConfig.h
*
* Main configuration parameters for the trace recorder library.
* More settings can be found in trcStreamingConfig.h and trcSnapshotConfig.h.
*
* Read more at http://percepio.com/2016/10/05/rtos-tracing/
*
* Terms of Use
* This file is part of the trace recorder library (RECORDER), which is the
* intellectual property of Percepio AB (PERCEPIO) and provided under a
* license as follows.
* The RECORDER may be used free of charge for the purpose of recording data
* intended for analysis in PERCEPIO products. It may not be used or modified
* for other purposes without explicit permission from PERCEPIO.
* You may distribute the RECORDER in its original source code form, assuming
* this text (terms of use, disclaimer, copyright notice) is unchanged. You are
* allowed to distribute the RECORDER with minor modifications intended for
* configuration or porting of the RECORDER, e.g., to allow using it on a
* specific processor, processor family or with a specific communication
* interface. Any such modifications should be documented directly below
* this comment block.
*
* Disclaimer
* The RECORDER is being delivered to you AS IS and PERCEPIO makes no warranty
* as to its use or performance. PERCEPIO does not and cannot warrant the
* performance or results you may obtain by using the RECORDER or documentation.
* PERCEPIO make no warranties, express or implied, as to noninfringement of
* third party rights, merchantability, or fitness for any particular purpose.
* In no event will PERCEPIO, its technology partners, or distributors be liable
* to you for any consequential, incidental or special damages, including any
* lost profits or lost savings, even if a representative of PERCEPIO has been
* advised of the possibility of such damages, or for any claim by any third
* party. Some jurisdictions do not allow the exclusion or limitation of
* incidental, consequential or special damages, or the exclusion of implied
* warranties or limitations on how long an implied warranty may last, so the
* above limitations may not apply to you.
*
* Tabs are used for indent in this file (1 tab = 4 spaces)
*
* Copyright Percepio AB, 2016.
* www.percepio.com
******************************************************************************/
#ifndef TRC_CONFIG_H
#define TRC_CONFIG_H
#ifdef __cplusplus
extern "C" {
#endif
#include "trcPortDefines.h"
/******************************************************************************
* Include of processor header file
*
* Here you may need to include the header file for your processor. This is
* required at least for the ARM Cortex-M port, that uses the ARM CMSIS API.
* Try that in case of build problems. Otherwise, remove the #error line below.
*****************************************************************************/
//#error "Trace Recorder: Please include your processor's header file here and remove this line."
#include "lpc18xx.h"
/*******************************************************************************
* Configuration Macro: TRC_CFG_HARDWARE_PORT
*
* Specify what hardware port to use (i.e., the "timestamping driver").
*
* All ARM Cortex-M MCUs are supported by "TRC_HARDWARE_PORT_ARM_Cortex_M".
* This port uses the DWT cycle counter for Cortex-M3/M4/M7 devices, which is
* available on most such devices. In case your device don't have DWT support,
* you will get an error message opening the trace. In that case, you may
* force the recorder to use SysTick timestamping instead, using this define:
*
* #define TRC_CFG_ARM_CM_USE_SYSTICK
*
* For ARM Cortex-M0/M0+ devices, SysTick mode is used automatically.
*
* See trcHardwarePort.h for available ports and information on how to
* define your own port, if not already present.
******************************************************************************/
#define TRC_CFG_HARDWARE_PORT TRC_HARDWARE_PORT_ARM_Cortex_M
/*******************************************************************************
* Configuration Macro: TRC_CFG_RECORDER_MODE
*
* Specify what recording mode to use. Snapshot means that the data is saved in
* an internal RAM buffer, for later upload. Streaming means that the data is
* transferred continuously to the host PC.
*
* For more information, see http://percepio.com/2016/10/05/rtos-tracing/
* and the Tracealyzer User Manual.
*
* Values:
* TRC_RECORDER_MODE_SNAPSHOT
* TRC_RECORDER_MODE_STREAMING
******************************************************************************/
#define TRC_CFG_RECORDER_MODE TRC_RECORDER_MODE_SNAPSHOT
/*******************************************************************************
* Configuration Macro: TRC_CFG_RECORDER_BUFFER_ALLOCATION
*
* Specifies how the recorder buffer is allocated (also in case of streaming, in
* port using the recorder's internal temporary buffer)
*
* Values:
* TRC_RECORDER_BUFFER_ALLOCATION_STATIC - Static allocation (internal)
* TRC_RECORDER_BUFFER_ALLOCATION_DYNAMIC - Malloc in vTraceEnable
* TRC_RECORDER_BUFFER_ALLOCATION_CUSTOM - Use vTraceSetRecorderDataBuffer
*
* Static and dynamic mode does the allocation for you, either in compile time
* (static) or in runtime (malloc).
* The custom mode allows you to control how and where the allocation is made,
* for details see TRC_ALLOC_CUSTOM_BUFFER and vTraceSetRecorderDataBuffer().
******************************************************************************/
#define TRC_CFG_RECORDER_BUFFER_ALLOCATION TRC_RECORDER_BUFFER_ALLOCATION_STATIC
/******************************************************************************
* TRC_CFG_FREERTOS_VERSION
*
* Specify what version of FreeRTOS that is used (don't change unless using the
* trace recorder library with an older version of FreeRTOS).
*
* TRC_FREERTOS_VERSION_7_3_OR_7_4 If using FreeRTOS v7.3.0 - v7.4.2
* TRC_FREERTOS_VERSION_7_5_OR_7_6 If using FreeRTOS v7.5.0 - v7.6.0
* TRC_FREERTOS_VERSION_8_X If using FreeRTOS v8.X.X
* TRC_FREERTOS_VERSION_9_X If using FreeRTOS v9.X.X
*****************************************************************************/
#define TRC_CFG_FREERTOS_VERSION TRC_FREERTOS_VERSION_9_X
/******************************************************************************
* TRC_CFG_MAX_ISR_NESTING
*
* Defines how many levels of interrupt nesting the recorder can handle, in
* case multiple ISRs are traced and ISR nesting is possible. If this
* is exceeded, the particular ISR will not be traced and the recorder then
* logs an error message. This setting is used to allocate an internal stack
* for keeping track of the previous execution context (4 byte per entry).
*
* This value must be a non-zero positive constant, at least 1.
*
* Default value: 8
*****************************************************************************/
#define TRC_CFG_MAX_ISR_NESTING 8
/* Specific configuration, depending on Streaming/Snapshot mode */
#if (TRC_CFG_RECORDER_MODE == TRC_RECORDER_MODE_SNAPSHOT)
#include "trcSnapshotConfig.h"
#elif (TRC_CFG_RECORDER_MODE == TRC_RECORDER_MODE_STREAMING)
#include "trcStreamingConfig.h"
#endif
#ifdef __cplusplus
}
#endif
#endif /* _TRC_CONFIG_H */