blob: 3309a1cbe40f3fcbf9879f3d1d76cb7e7c6b31ce [file] [log] [blame]
/* ----------------------------------------------------------------------------
* SAM Software Package License
* ----------------------------------------------------------------------------
* Copyright (c) 2011, Atmel Corporation
*
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* - Redistributions of source code must retain the above copyright notice,
* this list of conditions and the disclaimer below.
*
* Atmel's name may not be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
* OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
* EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
* ----------------------------------------------------------------------------
*/
#ifndef _GMII_DEFINE_H
#define _GMII_DEFINE_H
/*---------------------------------------------------------------------------
* Definitions
*---------------------------------------------------------------------------*/
//IEEE defined Registers
#define GMII_BMCR 0x0 // Basic Mode Control Register
#define GMII_BMSR 0x1 // Basic Mode Status Register
#define GMII_PHYID1R 0x2 // PHY Identifier Register 1
#define GMII_PHYID2R 0x3 // PHY Identifier Register 2
#define GMII_ANAR 0x4 // Auto_Negotiation Advertisement Register
#define GMII_ANLPAR 0x5 // Auto_negotiation Link Partner Ability Register
#define GMII_ANER 0x6 // Auto-negotiation Expansion Register
#define GMII_ANNPR 0x7 // Auto-negotiation Next Page Register
#define GMII_ANLPNPAR 0x8 // Auto_negotiation Link Partner Next Page Ability Register
#define GMII_AFEC0R 0x11 // AFE Control 0 Register
#define GMII_AFEC3R 0x14 // AFE Control 3 Register
#define GMII_RXERCR 0x15 // RXER Counter Register
#define GMII_OMSSR 0x17 // Operation Mode Strap Status Register
#define GMII_ECR 0x18 // Expanded Control Register
#define GMII_ICSR 0x1B // Interrupt Control/Status Register
#define GMII_FC 0x1C // Function Control
#define GMII_LCSR 0x1D // LinkMD® Control/Status Register
#define GMII_PC1R 0x1E // PHY Control 1 Register
#define GMII_PC2R 0x1F // PHY Control 2 Register
// PHY ID Identifier Register
#define GMII_LSB_MASK 0x0U
// definitions: MII_PHYID1
#define GMII_OUI_MSB 0x0022
// definitions: MII_PHYID2
#define GMII_OUI_LSB 0x1572 // KSZ8061 PHY Id2
// Basic Mode Control Register (BMCR)
// Bit definitions: MII_BMCR
#define GMII_RESET (1 << 15) // 1= Software Reset; 0=Normal Operation
#define GMII_LOOPBACK (1 << 14) // 1=loopback Enabled; 0=Normal Operation
#define GMII_SPEED_SELECT_LSB (1 << 13) // 1,0=1000Mbps 0,1=100Mbps; 0,0=10Mbps
#define GMII_AUTONEG (1 << 12) // Auto-negotiation Enable
#define GMII_POWER_DOWN (1 << 11) // 1=Power down 0=Normal operation
#define GMII_ISOLATE (1 << 10) // 1 = Isolates 0 = Normal operation
#define GMII_RESTART_AUTONEG (1 << 9) // 1 = Restart auto-negotiation 0 = Normal operation
#define GMII_DUPLEX_MODE (1 << 8) // 1 = Full duplex operation 0 = Normal operation
// Reserved 7 // Read as 0, ignore on write
#define GMII_SPEED_SELECT_MSB (1 << 6) //
// Reserved 5 to 0 // Read as 0, ignore on write
// Basic Mode Status Register (BMSR)
// Bit definitions: MII_BMSR
#define GMII_100BASE_T4 (1 << 15) // 100BASE-T4 Capable
#define GMII_100BASE_TX_FD (1 << 14) // 100BASE-TX Full Duplex Capable
#define GMII_100BASE_T4_HD (1 << 13) // 100BASE-TX Half Duplex Capable
#define GMII_10BASE_T_FD (1 << 12) // 10BASE-T Full Duplex Capable
#define GMII_10BASE_T_HD (1 << 11) // 10BASE-T Half Duplex Capable
// Reserved 10 to 9 // Read as 0, ignore on write
#define GMII_EXTEND_STATUS (1 << 8) // 1 = Extend Status Information In Reg 15
// Reserved 7
#define GMII_MF_PREAMB_SUPPR (1 << 6) // MII Frame Preamble Suppression
#define GMII_AUTONEG_COMP (1 << 5) // Auto-negotiation Complete
#define GMII_REMOTE_FAULT (1 << 4) // Remote Fault
#define GMII_AUTONEG_ABILITY (1 << 3) // Auto Configuration Ability
#define GMII_LINK_STATUS (1 << 2) // Link Status
#define GMII_JABBER_DETECT (1 << 1) // Jabber Detect
#define GMII_EXTEND_CAPAB (1 << 0) // Extended Capability
// Auto-negotiation Advertisement Register (ANAR)
// Auto-negotiation Link Partner Ability Register (ANLPAR)
// Bit definitions: MII_ANAR, MII_ANLPAR
#define GMII_NP (1 << 15) // Next page Indication
// Reserved 7
#define GMII_RF (1 << 13) // Remote Fault
// Reserved 12 // Write as 0, ignore on read
#define GMII_PAUSE_MASK (3 << 11) // 0,0 = No Pause 1,0 = Asymmetric Pause(link partner)
// 0,1 = Symmetric Pause 1,1 = Symmetric&Asymmetric Pause(local device)
#define GMII_T4 (1 << 9) // 100BASE-T4 Support
#define GMII_TX_FDX (1 << 8) // 100BASE-TX Full Duplex Support
#define GMII_TX_HDX (1 << 7) // 100BASE-TX Support
#define GMII_10_FDX (1 << 6) // 10BASE-T Full Duplex Support
#define GMII_10_HDX (1 << 5) // 10BASE-T Support
// Selector 4 to 0 // Protocol Selection Bits
#define GMII_AN_IEEE_802_3 0x00001
#endif // #ifndef _MII_DEFINE_H