| /*********************************************************************************************************************** | |
| * DISCLAIMER | |
| * This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products. No | |
| * other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all | |
| * applicable laws, including copyright laws. | |
| * THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING | |
| * THIS SOFTWARE, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, | |
| * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. TO THE MAXIMUM | |
| * EXTENT PERMITTED NOT PROHIBITED BY LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES | |
| * SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS | |
| * SOFTWARE, EVEN IF RENESAS OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. | |
| * Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability of | |
| * this software. By using this software, you agree to the additional terms and conditions found by accessing the | |
| * following link: | |
| * http://www.renesas.com/disclaimer | |
| * | |
| * Copyright (C) 2012 Renesas Electronics Corporation. All rights reserved. | |
| ***********************************************************************************************************************/ | |
| /*********************************************************************************************************************** | |
| * File Name : r_bsp_config_reference.c | |
| * Device(s) : RX111 | |
| * Description : The file r_bsp_config.h is used to configure your BSP. r_bsp_config.h should be included | |
| * somewhere in your package so that the r_bsp code has access to it. This file (r_bsp_config_reference.h) | |
| * is just a reference file that the user can use to make their own r_bsp_config.h file. | |
| ************************************************************************************************************************ | |
| * History : DD.MM.YYYY Version Description | |
| * : 07.11.2012 0.01 Beta Release | |
| ***********************************************************************************************************************/ | |
| #ifndef R_BSP_CONFIG_REF_HEADER_FILE | |
| #define R_BSP_CONFIG_REF_HEADER_FILE | |
| /*********************************************************************************************************************** | |
| Configuration Options | |
| ***********************************************************************************************************************/ | |
| /* Enter the product part number for your MCU. This information will be used to obtain information about your MCU such | |
| as package and memory size. | |
| To help parse this information, the part number will be defined using multiple macros. | |
| R 5 F 51 11 5 A D FM | |
| | | | | | | | | | Macro Name Description | |
| | | | | | | | | |__MCU_PART_PACKAGE = Package type, number of pins, and pin pitch | |
| | | | | | | | |____not used = Products with wide temperature range (D: -40 to 85C G: -40 to 105C) | |
| | | | | | | |______not used = Blank | |
| | | | | | |________MCU_PART_MEMORY_SIZE = ROM, RAM, and Data Flash Capacity | |
| | | | | |___________MCU_PART_GROUP = Group name | |
| | | | |______________MCU_PART_SERIES = Series name | |
| | | |________________MCU_PART_MEMORY_TYPE = Type of memory (Flash) | |
| | |__________________not used = Renesas MCU | |
| |____________________not used = Renesas semiconductor product. | |
| */ | |
| /* Package type. Set the macro definition based on values below: | |
| Character(s) = Value for macro = Package Type/Number of Pins/Pin Pitch | |
| FM = 0x0 = LFQFP/64/0.50 | |
| FK = 0x1 = LQFP/64/0.80 | |
| LF = 0x2 = TFLGA/64/0.50 | |
| FL = 0x3 = LFQFP/48/0.50 | |
| NE = 0x4 = VQFN/48/0.50 | |
| NC = 0x5 = HWQFN/36/0.50 | |
| LM = 0x6 = WFLGA/36/0.50 | |
| SB = 0x7 = SSOP/36/0.80 | |
| */ | |
| #define MCU_PART_PACKAGE (0x0) | |
| /* ROM, RAM, and Data Flash Capacity. | |
| Character(s) = Value for macro = ROM Size/Ram Size/Data Flash Size | |
| 5 = 0x5 = 128KB/16KB/8KB | |
| 4 = 0x4 = 96KB/16KB/8KB | |
| 3 = 0x3 = 64KB/10KB/8KB | |
| 1 = 0x1 = 32KB/10KB/8KB | |
| J = 0x0 = 16KB/8KB/8KB | |
| */ | |
| #define MCU_PART_MEMORY_SIZE (0x5) | |
| /* Group name. | |
| Character(s) = Value for macro = Description | |
| 10 = 0x0 = RX110 Group | |
| 11 = 0x1 = RX111 Group | |
| */ | |
| #define MCU_PART_GROUP (0x1) | |
| /* Series name. | |
| Character(s) = Value for macro = Description | |
| 51 = 0x0 = RX100 Series | |
| */ | |
| #define MCU_PART_SERIES (0x0) | |
| /* Memory type. | |
| Character(s) = Value for macro = Description | |
| F = 0x0 = Flash memory version | |
| */ | |
| #define MCU_PART_MEMORY_TYPE (0x0) | |
| /* The 'BSP_DECLARE_STACK' macro is checked so that the stack is only declared in one place (resetprg.c). Every time a | |
| '#pragma stacksize' is encountered, the stack size is increased. This prevents multiplication of stack size. */ | |
| #if defined(BSP_DECLARE_STACK) | |
| /* User Stack size in bytes. The Renesas RX toolchain sets the stack size using the #pragma stacksize directive. */ | |
| #pragma stacksize su=0x400 | |
| /* Interrupt Stack size in bytes. The Renesas RX toolchain sets the stack size using the #pragma stacksize directive. */ | |
| #pragma stacksize si=0x100 | |
| #endif | |
| /* Heap size in bytes. */ | |
| #define HEAP_BYTES (0x400) | |
| /* After reset MCU will operate in Supervisor mode. To switch to User mode, set this macro to '1'. For more information | |
| on the differences between these 2 modes see the CPU >> Processor Mode section of your MCU's hardware manual. | |
| 0 = Stay in Supervisor mode. | |
| 1 = Switch to User mode. | |
| */ | |
| #define RUN_IN_USER_MODE (0) | |
| /* This macro lets other modules no if a RTOS is being used. | |
| 0 = RTOS is not used. | |
| 1 = RTOS is used. | |
| */ | |
| #define RTOS_USED (0) | |
| /* Clock source select (CKSEL). | |
| 0 = Low Speed On-Chip Oscillator (LOCO) | |
| 1 = High Speed On-Chip Oscillator (HOCO) | |
| 2 = Main Clock Oscillator | |
| 3 = Sub-Clock Oscillator | |
| 4 = PLL Circuit | |
| */ | |
| #define CLOCK_SOURCE (4) | |
| /* Clock configuration options. | |
| The input clock frequency is specified and then the system clocks are set by specifying the multipliers used. The | |
| multiplier settings are used to set the clock registers in resetprg.c. If a 16MHz clock is used and the | |
| ICLK is 24MHz, PCLKB is 24MHz, FCLK is 24MHz, PCLKD is 24MHz, and CKO is 1MHz then the | |
| settings would be: | |
| XTAL_HZ = 16000000 | |
| PLL_DIV = 2 | |
| PLL_MUL = 6 (16MHz x 3 = 48MHz) | |
| ICK_DIV = 2 : System Clock (ICLK) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / ICK_DIV) = 24MHz | |
| PCKB_DIV = 2 : Peripheral Clock B (PCLKB) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / PCKB_DIV) = 24MHz | |
| PCKD_DIV = 2 : Peripheral Clock D (PCLKD) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / PCKD_DIV) = 24MHz | |
| FCK_DIV = 2 : Flash IF Clock (FCLK) = (((XTAL_HZ/PLL_DIV) * PLL_MUL) / FCK_DIV) = 24MHz | |
| */ | |
| /* XTAL - Input clock frequency in Hz */ | |
| #define XTAL_HZ (16000000) | |
| /* PLL Input Frequency Divider Select (PLIDIV). | |
| Available divisors = /1 (no division), /2, /4 | |
| */ | |
| #define PLL_DIV (2) | |
| /* PLL Frequency Multiplication Factor Select (STC). | |
| Available multipliers = x6, x8 | |
| */ | |
| #define PLL_MUL (6) | |
| /* System Clock Divider (ICK). | |
| Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64 | |
| */ | |
| #define ICK_DIV (2) | |
| /* Peripheral Module Clock B Divider (PCKB). | |
| Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64 | |
| */ | |
| #define PCKB_DIV (2) | |
| /* Peripheral Module Clock D Divider (PCKD). | |
| Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64 | |
| */ | |
| #define PCKD_DIV (2) | |
| /* Flash IF Clock Divider (FCK). | |
| Available divisors = /1 (no division), /2, /4, /8, /16, /32, /64 | |
| */ | |
| #define FCK_DIV (2) | |
| /* Below are callback functions that can be used for detecting MCU exceptions, undefined interrupt sources, and | |
| bus errors. If the user wishes to be alerted of these events then they will need to define the macro as a | |
| function to be called when the event occurs. For example, if the user wanted the function | |
| excep_undefined_instr_isr() to be called when an undefined interrupt source ISR is triggered then they would | |
| do the following: | |
| #define UNDEFINED_INT_ISR_CALLBACK undefined_interrupt_cb | |
| If the user does not wish to be alerted of these events then they should comment out the macros. | |
| NOTE: When a callback function is called it will be called from within a ISR. This means that the function | |
| will essentially be an interrupt and will hold off other interrupts that occur in the system while it | |
| is executing. For this reason, it is recommended to keep these callback functions short as to not | |
| decrease the real-time response of your system. | |
| */ | |
| /* Callback for Supervisor Instruction Violation Exception. */ | |
| //#define EXCEP_SUPERVISOR_ISR_CALLBACK supervisor_instr_cb | |
| /* Callback for Undefined Instruction Exception. */ | |
| //#define EXCEP_UNDEFINED_INSTR_ISR_CALLBACK undefined_instr_cb | |
| /* Callback for Non-maskable Interrupt. */ | |
| //#define NMI_ISR_CALLBACK nmi_cb | |
| /* Callback for all undefined interrupt vectors. User can set a breakpoint in this function to determine which source | |
| is creating unwanted interrupts. */ | |
| //#define UNDEFINED_INT_ISR_CALLBACK undefined_interrupt_cb | |
| /* Callback for Bus Error Interrupt. */ | |
| //#define BUS_ERROR_ISR_CALLBACK bus_error_cb | |
| /* The user has the option of separately choosing little or big endian for the User Application Area */ | |
| /* Endian mode for User Application. | |
| 0 = Big Endian | |
| Else = Little Endian (Default) | |
| */ | |
| #define USER_APP_ENDIAN (1) | |
| /* Configure WDT and IWDT settings. | |
| OFS0 - Option Function Select Register 0 | |
| OFS0 - Option Function Select Register 0 | |
| b31:b15 Reserved (set to 1) | |
| b14 IWDTSLCSTP - IWDT Sleep Mode Count Stop Control - (0=can't stop count, 1=stop w/some low power modes) | |
| b13 Reserved (set to 1) | |
| b12 IWDTRSTIRQS - IWDT Reset Interrupt Request - What to do on underflow (0=take interrupt, 1=reset MCU) | |
| b11:b10 IWDTRPSS - IWDT Window Start Position Select - (0=25%, 1=50%, 2=75%, 3=100%,don't use) | |
| b9:b8 IWDTRPES - IWDT Window End Position Select - (0=75%, 1=50%, 2=25%, 3=0%,don't use) | |
| b7:b4 IWDTCKS - IWDT Clock Frequency Division Ratio - (0=none, 2=/16, 3 = /32, 4=/64, 0xF=/128, 5=/256) | |
| b3:b2 IWDTTOPS - IWDT Timeout Period Select - (0=128 cycles, 1=512, 2=1024, 3=2048) | |
| b1 IWDTSTRT - IWDT Start Mode Select - (0=auto-start after reset, 1=halt after reset) | |
| b0 Reserved (set to 1) */ | |
| #define OFS0_REG_VALUE (0xFFFFFFFF) //Disable by default | |
| /* Configure whether voltage detection 1 circuit and HOCO are enabled after reset. | |
| OFS1 - Option Function Select Register 1 | |
| b31:b9 Reserved (set to 1) | |
| b8 HOCOEN - Enable/disable HOCO oscillation after a reset (0=enable, 1=disable) | |
| b7:b4 STUPLVD1LVL - Startup Voltage Monitoring 1 Reset Detection Level Select | |
| 0 1 0 0: 3.10 V | |
| 0 1 0 1: 3.00 V | |
| 0 1 1 0: 2.90 V | |
| 0 1 1 1: 2.79 V | |
| 1 0 0 0: 2.68 V | |
| 1 0 0 1: 2.58 V | |
| 1 0 1 0: 2.48 V | |
| 1 0 1 1: 2.06 V | |
| 1 1 0 0: 1.96 V | |
| 1 1 0 1: 1.86 V | |
| b3:b2 Reserved (set to 1) | |
| b2 STUPLVD1REN - Startup Voltage Monitoring 1 Reset Enable (1=monitoring disabled) | |
| b0 FASTSTUP - Power-On Fast Startup Time (1=normal; read only) */ | |
| #define OFS1_REG_VALUE (0xFFFFFFFF) //Disable by default | |
| /* Initializes C input & output library functions. | |
| 0 = Disable I/O library initialization in resetprg.c. If you are not using stdio then use this value. | |
| 1 = Enable I/O library initialization in resetprg.c. This is default and needed if you are using stdio. */ | |
| #define IO_LIB_ENABLE (1) | |
| #endif /* R_BSP_CONFIG_REF_HEADER_FILE */ | |