blob: a9926bb75922318a9f193752637d6505bc9429a5 [file] [log] [blame]
/*
* linux/arch/arm/mach-pxa/cm-x270.c
*
* Copyright (C) 2007, 2008 CompuLab, Ltd.
* Mike Rapoport <mike@compulab.co.il>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/platform_device.h>
#include <linux/sysdev.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/rtc-v3020.h>
#include <video/mbxfb.h>
#include <linux/spi/spi.h>
#include <linux/spi/libertas_spi.h>
#include <mach/pxa27x.h>
#include <mach/ohci.h>
#include <mach/mmc.h>
#include <mach/pxa2xx_spi.h>
#include "generic.h"
/* physical address if local-bus attached devices */
#define RTC_PHYS_BASE (PXA_CS1_PHYS + (5 << 22))
/* GPIO IRQ usage */
#define GPIO83_MMC_IRQ (83)
#define CMX270_MMC_IRQ IRQ_GPIO(GPIO83_MMC_IRQ)
/* MMC power enable */
#define GPIO105_MMC_POWER (105)
/* WLAN GPIOS */
#define GPIO19_WLAN_STRAP (19)
#define GPIO102_WLAN_RST (102)
static unsigned long cmx270_pin_config[] = {
/* AC'97 */
GPIO28_AC97_BITCLK,
GPIO29_AC97_SDATA_IN_0,
GPIO30_AC97_SDATA_OUT,
GPIO31_AC97_SYNC,
GPIO98_AC97_SYSCLK,
GPIO113_AC97_nRESET,
/* BTUART */
GPIO42_BTUART_RXD,
GPIO43_BTUART_TXD,
GPIO44_BTUART_CTS,
GPIO45_BTUART_RTS,
/* STUART */
GPIO46_STUART_RXD,
GPIO47_STUART_TXD,
/* MCI controller */
GPIO32_MMC_CLK,
GPIO112_MMC_CMD,
GPIO92_MMC_DAT_0,
GPIO109_MMC_DAT_1,
GPIO110_MMC_DAT_2,
GPIO111_MMC_DAT_3,
/* LCD */
GPIOxx_LCD_TFT_16BPP,
/* I2C */
GPIO117_I2C_SCL,
GPIO118_I2C_SDA,
/* SSP1 */
GPIO23_SSP1_SCLK,
GPIO24_SSP1_SFRM,
GPIO25_SSP1_TXD,
GPIO26_SSP1_RXD,
/* SSP2 */
GPIO19_GPIO, /* SSP2 clock is used as GPIO for Libertas pin-strap */
GPIO14_GPIO,
GPIO87_SSP2_TXD,
GPIO88_SSP2_RXD,
/* PC Card */
GPIO48_nPOE,
GPIO49_nPWE,
GPIO50_nPIOR,
GPIO51_nPIOW,
GPIO85_nPCE_1,
GPIO54_nPCE_2,
GPIO55_nPREG,
GPIO56_nPWAIT,
GPIO57_nIOIS16,
/* SDRAM and local bus */
GPIO15_nCS_1,
GPIO78_nCS_2,
GPIO79_nCS_3,
GPIO80_nCS_4,
GPIO33_nCS_5,
GPIO49_nPWE,
GPIO18_RDY,
/* GPIO */
GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,
GPIO105_GPIO | MFP_LPM_DRIVE_HIGH, /* MMC/SD power */
GPIO53_GPIO, /* PC card reset */
GPIO102_GPIO, /* WLAN reset */
/* NAND controls */
GPIO11_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */
GPIO89_GPIO, /* NAND Ready/Busy */
/* interrupts */
GPIO10_GPIO, /* DM9000 interrupt */
GPIO83_GPIO, /* MMC card detect */
GPIO95_GPIO, /* WLAN interrupt */
};
/* V3020 RTC */
#if defined(CONFIG_RTC_DRV_V3020) || defined(CONFIG_RTC_DRV_V3020_MODULE)
static struct resource cmx270_v3020_resource[] = {
[0] = {
.start = RTC_PHYS_BASE,
.end = RTC_PHYS_BASE + 4,
.flags = IORESOURCE_MEM,
},
};
struct v3020_platform_data cmx270_v3020_pdata = {
.leftshift = 16,
};
static struct platform_device cmx270_rtc_device = {
.name = "v3020",
.num_resources = ARRAY_SIZE(cmx270_v3020_resource),
.resource = cmx270_v3020_resource,
.id = -1,
.dev = {
.platform_data = &cmx270_v3020_pdata,
}
};
static void __init cmx270_init_rtc(void)
{
platform_device_register(&cmx270_rtc_device);
}
#else
static inline void cmx270_init_rtc(void) {}
#endif
/* 2700G graphics */
#if defined(CONFIG_FB_MBX) || defined(CONFIG_FB_MBX_MODULE)
static u64 fb_dma_mask = ~(u64)0;
static struct resource cmx270_2700G_resource[] = {
/* frame buffer memory including ODFB and External SDRAM */
[0] = {
.start = PXA_CS2_PHYS,
.end = PXA_CS2_PHYS + 0x01ffffff,
.flags = IORESOURCE_MEM,
},
/* Marathon registers */
[1] = {
.start = PXA_CS2_PHYS + 0x03fe0000,
.end = PXA_CS2_PHYS + 0x03ffffff,
.flags = IORESOURCE_MEM,
},
};
static unsigned long cmx270_marathon_on[] = {
GPIO58_GPIO,
GPIO59_GPIO,
GPIO60_GPIO,
GPIO61_GPIO,
GPIO62_GPIO,
GPIO63_GPIO,
GPIO64_GPIO,
GPIO65_GPIO,
GPIO66_GPIO,
GPIO67_GPIO,
GPIO68_GPIO,
GPIO69_GPIO,
GPIO70_GPIO,
GPIO71_GPIO,
GPIO72_GPIO,
GPIO73_GPIO,
GPIO74_GPIO,
GPIO75_GPIO,
GPIO76_GPIO,
GPIO77_GPIO,
};
static unsigned long cmx270_marathon_off[] = {
GPIOxx_LCD_TFT_16BPP,
};
static int cmx270_marathon_probe(struct fb_info *fb)
{
int gpio, err;
for (gpio = 58; gpio <= 77; gpio++) {
err = gpio_request(gpio, "LCD");
if (err)
return err;
gpio_direction_input(gpio);
}
pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_on));
return 0;
}
static int cmx270_marathon_remove(struct fb_info *fb)
{
int gpio;
pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_off));
for (gpio = 58; gpio <= 77; gpio++)
gpio_free(gpio);
return 0;
}
static struct mbxfb_platform_data cmx270_2700G_data = {
.xres = {
.min = 240,
.max = 1200,
.defval = 640,
},
.yres = {
.min = 240,
.max = 1200,
.defval = 480,
},
.bpp = {
.min = 16,
.max = 32,
.defval = 16,
},
.memsize = 8*1024*1024,
.probe = cmx270_marathon_probe,
.remove = cmx270_marathon_remove,
};
static struct platform_device cmx270_2700G = {
.name = "mbx-fb",
.dev = {
.platform_data = &cmx270_2700G_data,
.dma_mask = &fb_dma_mask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(cmx270_2700G_resource),
.resource = cmx270_2700G_resource,
.id = -1,
};
static void __init cmx270_init_2700G(void)
{
platform_device_register(&cmx270_2700G);
}
#else
static inline void cmx270_init_2700G(void) {}
#endif
/* PXA27x OHCI controller setup */
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
static struct pxaohci_platform_data cmx270_ohci_platform_data = {
.port_mode = PMM_PERPORT_MODE,
.flags = ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW,
};
static void __init cmx270_init_ohci(void)
{
pxa_set_ohci_info(&cmx270_ohci_platform_data);
}
#else
static inline void cmx270_init_ohci(void) {}
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
static struct pxamci_platform_data cmx270_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.gpio_card_detect = GPIO83_MMC_IRQ,
.gpio_card_ro = -1,
.gpio_power = GPIO105_MMC_POWER,
.gpio_power_invert = 1,
};
static void __init cmx270_init_mmc(void)
{
pxa_set_mci_info(&cmx270_mci_platform_data);
}
#else
static inline void cmx270_init_mmc(void) {}
#endif
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
static struct pxa2xx_spi_master cm_x270_spi_info = {
.num_chipselect = 1,
.enable_dma = 1,
};
static struct pxa2xx_spi_chip cm_x270_libertas_chip = {
.rx_threshold = 1,
.tx_threshold = 1,
.timeout = 1000,
.gpio_cs = 14,
};
static unsigned long cm_x270_libertas_pin_config[] = {
/* SSP2 */
GPIO19_SSP2_SCLK,
GPIO14_GPIO,
GPIO87_SSP2_TXD,
GPIO88_SSP2_RXD,
};
static int cm_x270_libertas_setup(struct spi_device *spi)
{
int err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
if (err)
return err;
err = gpio_request(GPIO102_WLAN_RST, "WLAN RST");
if (err)
goto err_free_strap;
err = gpio_direction_output(GPIO102_WLAN_RST, 0);
if (err)
goto err_free_strap;
msleep(100);
err = gpio_direction_output(GPIO19_WLAN_STRAP, 1);
if (err)
goto err_free_strap;
msleep(100);
pxa2xx_mfp_config(ARRAY_AND_SIZE(cm_x270_libertas_pin_config));
gpio_set_value(GPIO102_WLAN_RST, 1);
msleep(100);
spi->bits_per_word = 16;
spi_setup(spi);
return 0;
err_free_strap:
gpio_free(GPIO19_WLAN_STRAP);
return err;
}
static int cm_x270_libertas_teardown(struct spi_device *spi)
{
gpio_set_value(GPIO102_WLAN_RST, 0);
gpio_free(GPIO102_WLAN_RST);
gpio_free(GPIO19_WLAN_STRAP);
return 0;
}
struct libertas_spi_platform_data cm_x270_libertas_pdata = {
.use_dummy_writes = 1,
.setup = cm_x270_libertas_setup,
.teardown = cm_x270_libertas_teardown,
};
static struct spi_board_info cm_x270_spi_devices[] __initdata = {
{
.modalias = "libertas_spi",
.max_speed_hz = 13000000,
.bus_num = 2,
.irq = gpio_to_irq(95),
.chip_select = 0,
.controller_data = &cm_x270_libertas_chip,
.platform_data = &cm_x270_libertas_pdata,
},
};
static void __init cmx270_init_spi(void)
{
pxa2xx_set_spi_info(2, &cm_x270_spi_info);
spi_register_board_info(ARRAY_AND_SIZE(cm_x270_spi_devices));
}
#else
static inline void cmx270_init_spi(void) {}
#endif
void __init cmx270_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_pin_config));
#ifdef CONFIG_PM
pxa27x_set_pwrmode(PWRMODE_DEEPSLEEP);
#endif
cmx270_init_rtc();
cmx270_init_mmc();
cmx270_init_ohci();
cmx270_init_2700G();
cmx270_init_spi();
}