blob: eb27976dab373134478409f64b9f65c6a6ea4219 [file] [log] [blame]
/*
* Linux ARCnet driver - COM90xx chipset (IO-mapped buffers)
*
* Written 1997 by David Woodhouse.
* Written 1994-1999 by Avery Pennarun.
* Written 1999-2000 by Martin Mares <mj@ucw.cz>.
* Derived from skeleton.c by Donald Becker.
*
* Special thanks to Contemporary Controls, Inc. (www.ccontrols.com)
* for sponsoring the further development of this driver.
*
* **********************
*
* The original copyright of skeleton.c was as follows:
*
* skeleton.c Written 1993 by Donald Becker.
* Copyright 1993 United States Government as represented by the
* Director, National Security Agency. This software may only be used
* and distributed according to the terms of the GNU General Public License as
* modified by SRC, incorporated herein by reference.
*
* **********************
*
* For more details, see drivers/net/arcnet.c
*
* **********************
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/ioport.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/bootmem.h>
#include <linux/init.h>
#include <asm/io.h>
#include <linux/arcdevice.h>
#define VERSION "arcnet: COM90xx IO-mapped mode support (by David Woodhouse et el.)\n"
/* Internal function declarations */
static int com90io_found(struct net_device *dev);
static void com90io_command(struct net_device *dev, int command);
static int com90io_status(struct net_device *dev);
static void com90io_setmask(struct net_device *dev, int mask);
static int com90io_reset(struct net_device *dev, int really_reset);
static void com90io_copy_to_card(struct net_device *dev, int bufnum, int offset,
void *buf, int count);
static void com90io_copy_from_card(struct net_device *dev, int bufnum, int offset,
void *buf, int count);
/* Handy defines for ARCnet specific stuff */
/* The number of low I/O ports used by the card. */
#define ARCNET_TOTAL_SIZE 16
/* COM 9026 controller chip --> ARCnet register addresses */
#define _INTMASK (ioaddr+0) /* writable */
#define _STATUS (ioaddr+0) /* readable */
#define _COMMAND (ioaddr+1) /* writable, returns random vals on read (?) */
#define _RESET (ioaddr+8) /* software reset (on read) */
#define _MEMDATA (ioaddr+12) /* Data port for IO-mapped memory */
#define _ADDR_HI (ioaddr+15) /* Control registers for said */
#define _ADDR_LO (ioaddr+14)
#define _CONFIG (ioaddr+2) /* Configuration register */
#undef ASTATUS
#undef ACOMMAND
#undef AINTMASK
#define ASTATUS() inb(_STATUS)
#define ACOMMAND(cmd) outb((cmd),_COMMAND)
#define AINTMASK(msk) outb((msk),_INTMASK)
#define SETCONF() outb((lp->config),_CONFIG)
/****************************************************************************
* *
* IO-mapped operation routines *
* *
****************************************************************************/
#undef ONE_AT_A_TIME_TX
#undef ONE_AT_A_TIME_RX
static u_char get_buffer_byte(struct net_device *dev, unsigned offset)
{
int ioaddr = dev->base_addr;
outb(offset >> 8, _ADDR_HI);
outb(offset & 0xff, _ADDR_LO);
return inb(_MEMDATA);
}
#ifdef ONE_AT_A_TIME_TX
static void put_buffer_byte(struct net_device *dev, unsigned offset, u_char datum)
{
int ioaddr = dev->base_addr;
outb(offset >> 8, _ADDR_HI);
outb(offset & 0xff, _ADDR_LO);
outb(datum, _MEMDATA);
}
#endif
static void get_whole_buffer(struct net_device *dev, unsigned offset, unsigned length, char *dest)
{
int ioaddr = dev->base_addr;
outb((offset >> 8) | AUTOINCflag, _ADDR_HI);
outb(offset & 0xff, _ADDR_LO);
while (length--)
#ifdef ONE_AT_A_TIME_RX
*(dest++) = get_buffer_byte(dev, offset++);
#else
*(dest++) = inb(_MEMDATA);
#endif
}
static void put_whole_buffer(struct net_device *dev, unsigned offset, unsigned length, char *dest)
{
int ioaddr = dev->base_addr;
outb((offset >> 8) | AUTOINCflag, _ADDR_HI);
outb(offset & 0xff, _ADDR_LO);
while (length--)
#ifdef ONE_AT_A_TIME_TX
put_buffer_byte(dev, offset++, *(dest++));
#else
outb(*(dest++), _MEMDATA);
#endif
}
/*
* We cannot probe for an IO mapped card either, although we can check that
* it's where we were told it was, and even autoirq
*/
static int __init com90io_probe(struct net_device *dev)
{
int ioaddr = dev->base_addr, status;
unsigned long airqmask;
BUGLVL(D_NORMAL) printk(VERSION);
BUGLVL(D_NORMAL) printk("E-mail me if you actually test this driver, please!\n");
if (!ioaddr) {
BUGMSG(D_NORMAL, "No autoprobe for IO mapped cards; you "
"must specify the base address!\n");
return -ENODEV;
}
if (!request_region(ioaddr, ARCNET_TOTAL_SIZE, "com90io probe")) {
BUGMSG(D_INIT_REASONS, "IO request_region %x-%x failed.\n",
ioaddr, ioaddr + ARCNET_TOTAL_SIZE - 1);
return -ENXIO;
}
if (ASTATUS() == 0xFF) {
BUGMSG(D_INIT_REASONS, "IO address %x empty\n", ioaddr);
goto err_out;
}
inb(_RESET);
mdelay(RESETtime);
status = ASTATUS();
if ((status & 0x9D) != (NORXflag | RECONflag | TXFREEflag | RESETflag)) {
BUGMSG(D_INIT_REASONS, "Status invalid (%Xh).\n", status);
goto err_out;
}
BUGMSG(D_INIT_REASONS, "Status after reset: %X\n", status);
ACOMMAND(CFLAGScmd | RESETclear | CONFIGclear);
BUGMSG(D_INIT_REASONS, "Status after reset acknowledged: %X\n", status);
status = ASTATUS();
if (status & RESETflag) {
BUGMSG(D_INIT_REASONS, "Eternal reset (status=%Xh)\n", status);
goto err_out;
}
outb((0x16 | IOMAPflag) & ~ENABLE16flag, _CONFIG);
/* Read first loc'n of memory */
outb(AUTOINCflag, _ADDR_HI);
outb(0, _ADDR_LO);
if ((status = inb(_MEMDATA)) != 0xd1) {
BUGMSG(D_INIT_REASONS, "Signature byte not found"
" (%Xh instead).\n", status);
goto err_out;
}
if (!dev->irq) {
/*
* if we do this, we're sure to get an IRQ since the
* card has just reset and the NORXflag is on until
* we tell it to start receiving.
*/
airqmask = probe_irq_on();
outb(NORXflag, _INTMASK);
udelay(1);
outb(0, _INTMASK);
dev->irq = probe_irq_off(airqmask);
if ((int)dev->irq <= 0) {
BUGMSG(D_INIT_REASONS, "Autoprobe IRQ failed\n");
goto err_out;
}
}
release_region(ioaddr, ARCNET_TOTAL_SIZE); /* end of probing */
return com90io_found(dev);
err_out:
release_region(ioaddr, ARCNET_TOTAL_SIZE);
return -ENODEV;
}
/* Set up the struct net_device associated with this card. Called after
* probing succeeds.
*/
static int __init com90io_found(struct net_device *dev)
{
struct arcnet_local *lp;
int ioaddr = dev->base_addr;
int err;
/* Reserve the irq */
if (request_irq(dev->irq, arcnet_interrupt, 0, "arcnet (COM90xx-IO)", dev)) {
BUGMSG(D_NORMAL, "Can't get IRQ %d!\n", dev->irq);
return -ENODEV;
}
/* Reserve the I/O region */
if (!request_region(dev->base_addr, ARCNET_TOTAL_SIZE, "arcnet (COM90xx-IO)")) {
free_irq(dev->irq, dev);
return -EBUSY;
}
lp = netdev_priv(dev);
lp->card_name = "COM90xx I/O";
lp->hw.command = com90io_command;
lp->hw.status = com90io_status;
lp->hw.intmask = com90io_setmask;
lp->hw.reset = com90io_reset;
lp->hw.owner = THIS_MODULE;
lp->hw.copy_to_card = com90io_copy_to_card;
lp->hw.copy_from_card = com90io_copy_from_card;
lp->config = (0x16 | IOMAPflag) & ~ENABLE16flag;
SETCONF();
/* get and check the station ID from offset 1 in shmem */
dev->dev_addr[0] = get_buffer_byte(dev, 1);
err = register_netdev(dev);
if (err) {
outb((inb(_CONFIG) & ~IOMAPflag), _CONFIG);
free_irq(dev->irq, dev);
release_region(dev->base_addr, ARCNET_TOTAL_SIZE);
return err;
}
BUGMSG(D_NORMAL, "COM90IO: station %02Xh found at %03lXh, IRQ %d.\n",
dev->dev_addr[0], dev->base_addr, dev->irq);
return 0;
}
/*
* Do a hardware reset on the card, and set up necessary registers.
*
* This should be called as little as possible, because it disrupts the
* token on the network (causes a RECON) and requires a significant delay.
*
* However, it does make sure the card is in a defined state.
*/
static int com90io_reset(struct net_device *dev, int really_reset)
{
struct arcnet_local *lp = netdev_priv(dev);
short ioaddr = dev->base_addr;
BUGMSG(D_INIT, "Resetting %s (status=%02Xh)\n", dev->name, ASTATUS());
if (really_reset) {
/* reset the card */
inb(_RESET);
mdelay(RESETtime);
}
/* Set the thing to IO-mapped, 8-bit mode */
lp->config = (0x1C | IOMAPflag) & ~ENABLE16flag;
SETCONF();
ACOMMAND(CFLAGScmd | RESETclear); /* clear flags & end reset */
ACOMMAND(CFLAGScmd | CONFIGclear);
/* verify that the ARCnet signature byte is present */
if (get_buffer_byte(dev, 0) != TESTvalue) {
BUGMSG(D_NORMAL, "reset failed: TESTvalue not present.\n");
return 1;
}
/* enable extended (512-byte) packets */
ACOMMAND(CONFIGcmd | EXTconf);
/* done! return success. */
return 0;
}
static void com90io_command(struct net_device *dev, int cmd)
{
short ioaddr = dev->base_addr;
ACOMMAND(cmd);
}
static int com90io_status(struct net_device *dev)
{
short ioaddr = dev->base_addr;
return ASTATUS();
}
static void com90io_setmask(struct net_device *dev, int mask)
{
short ioaddr = dev->base_addr;
AINTMASK(mask);
}
static void com90io_copy_to_card(struct net_device *dev, int bufnum, int offset,
void *buf, int count)
{
TIME("put_whole_buffer", count, put_whole_buffer(dev, bufnum * 512 + offset, count, buf));
}
static void com90io_copy_from_card(struct net_device *dev, int bufnum, int offset,
void *buf, int count)
{
TIME("get_whole_buffer", count, get_whole_buffer(dev, bufnum * 512 + offset, count, buf));
}
static int io; /* use the insmod io= irq= shmem= options */
static int irq;
static char device[9]; /* use eg. device=arc1 to change name */
module_param(io, int, 0);
module_param(irq, int, 0);
module_param_string(device, device, sizeof(device), 0);
MODULE_LICENSE("GPL");
#ifndef MODULE
static int __init com90io_setup(char *s)
{
int ints[4];
s = get_options(s, 4, ints);
if (!ints[0])
return 0;
switch (ints[0]) {
default: /* ERROR */
printk("com90io: Too many arguments.\n");
case 2: /* IRQ */
irq = ints[2];
case 1: /* IO address */
io = ints[1];
}
if (*s)
snprintf(device, sizeof(device), "%s", s);
return 1;
}
__setup("com90io=", com90io_setup);
#endif
static struct net_device *my_dev;
static int __init com90io_init(void)
{
struct net_device *dev;
int err;
dev = alloc_arcdev(device);
if (!dev)
return -ENOMEM;
dev->base_addr = io;
dev->irq = irq;
if (dev->irq == 2)
dev->irq = 9;
err = com90io_probe(dev);
if (err) {
free_netdev(dev);
return err;
}
my_dev = dev;
return 0;
}
static void __exit com90io_exit(void)
{
struct net_device *dev = my_dev;
int ioaddr = dev->base_addr;
unregister_netdev(dev);
/* Set the thing back to MMAP mode, in case the old driver is loaded later */
outb((inb(_CONFIG) & ~IOMAPflag), _CONFIG);
free_irq(dev->irq, dev);
release_region(dev->base_addr, ARCNET_TOTAL_SIZE);
free_netdev(dev);
}
module_init(com90io_init)
module_exit(com90io_exit)