| //------------------------------------------------------------------------------ |
| // Copyright (c) 2004-2010 Atheros Corporation. All rights reserved. |
| // |
| // |
| // Permission to use, copy, modify, and/or distribute this software for any |
| // purpose with or without fee is hereby granted, provided that the above |
| // copyright notice and this permission notice appear in all copies. |
| // |
| // THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| // WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| // MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| // ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| // WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| // ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| // OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| // |
| // |
| //------------------------------------------------------------------------------ |
| //============================================================================== |
| // This file contains the tunable configuration items for the WLAN module |
| // |
| // Author(s): ="Atheros" |
| //============================================================================== |
| #ifndef _HOST_WLAN_CONFIG_H_ |
| #define _HOST_WLAN_CONFIG_H_ |
| |
| /* Include definitions here that can be used to tune the WLAN module behavior. |
| * Different customers can tune the behavior as per their needs, here. |
| */ |
| |
| /* This configuration item when defined will consider the barker preamble |
| * mentioned in the ERP IE of the beacons from the AP to determine the short |
| * preamble support sent in the (Re)Assoc request frames. |
| */ |
| #define WLAN_CONFIG_DONOT_IGNORE_BARKER_IN_ERP 0 |
| |
| /* This config item when defined will not send the power module state transition |
| * failure events that happen during scan, to the host. |
| */ |
| #define WLAN_CONFIG_IGNORE_POWER_SAVE_FAIL_EVENT_DURING_SCAN 0 |
| |
| /* |
| * This configuration item enable/disable keepalive support. |
| * Keepalive support: In the absence of any data traffic to AP, null |
| * frames will be sent to the AP at periodic interval, to keep the association |
| * active. This configuration item defines the periodic interval. |
| * Use value of zero to disable keepalive support |
| * Default: 60 seconds |
| */ |
| #define WLAN_CONFIG_KEEP_ALIVE_INTERVAL 60 |
| |
| /* |
| * This configuration item sets the value of disconnect timeout |
| * Firmware delays sending the disconnec event to the host for this |
| * timeout after is gets disconnected from the current AP. |
| * If the firmware successly roams within the disconnect timeout |
| * it sends a new connect event |
| */ |
| #ifdef ANDROID_ENV |
| #define WLAN_CONFIG_DISCONNECT_TIMEOUT 3 |
| #else |
| #define WLAN_CONFIG_DISCONNECT_TIMEOUT 10 |
| #endif /* ANDROID_ENV */ |
| |
| /* |
| * This configuration item disables 11n support. |
| * 0 - Enable |
| * 1 - Disable |
| */ |
| #define WLAN_CONFIG_DISABLE_11N 0 |
| |
| /* |
| * This configuration item enable BT clock sharing support |
| * 1 - Enable |
| * 0 - Disable (Default) |
| */ |
| #define WLAN_CONFIG_BT_SHARING 0 |
| |
| /* |
| * This configuration item sets WIFI OFF policy |
| * 0 - CUT_POWER |
| * 1 - DEEP_SLEEP (Default) |
| */ |
| #define WLAN_CONFIG_WLAN_OFF 1 |
| |
| /* |
| * This configuration item sets suspend policy |
| * 0 - CUT_POWER (Default) |
| * 1 - DEEP_SLEEP |
| * 2 - WoW |
| * 3 - CUT_POWER if BT OFF (clock sharing designs only) |
| */ |
| #define WLAN_CONFIG_PM_SUSPEND 0 |
| |
| /* |
| * This configuration item sets suspend policy to use if PM_SUSPEND is |
| * set to WoW and device is not connected at the time of suspend |
| * 0 - CUT_POWER (Default) |
| * 1 - DEEP_SLEEP |
| * 2 - WoW |
| * 3 - CUT_POWER if BT OFF (clock sharing designs only) |
| */ |
| #define WLAN_CONFIG_PM_WOW2 0 |
| |
| /* |
| * Platform specific function to power ON/OFF AR6000 |
| * and enable/disable SDIO card detection |
| */ |
| #define plat_setup_power(on, detect) |
| |
| #endif /* _HOST_WLAN_CONFIG_H_ */ |
