| config AXP221_POWER | |
| boolean "axp221 / axp223 pmic support" | |
| depends on MACH_SUN6I || MACH_SUN8I | |
| default y | |
| ---help--- | |
| Say y here to enable support for the axp221 / axp223 pmic found on most | |
| sun6i (A31) / sun8i (A23) boards. | |
| config AXP221_DCDC1_VOLT | |
| int "axp221 dcdc1 voltage" | |
| depends on AXP221_POWER | |
| default 3000 | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 dcdc1 at, set to 0 to | |
| disable dcdc1. This is typically used as generic 3.3V IO voltage for | |
| things like GPIO-s, sdcard interfaces, etc. On most boards this is | |
| undervolted to 3.0V to safe battery. | |
| config AXP221_DLDO1_VOLT | |
| int "axp221 dldo1 voltage" | |
| depends on AXP221_POWER | |
| default 0 | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 dldo1 at, set to 0 to | |
| disable dldo1. On sun6i (A31) boards with ethernet this is often used | |
| to power the ethernet phy. On sun8i (A23) boards this is often used to | |
| power the wifi. | |
| config AXP221_DLDO4_VOLT | |
| int "axp221 dldo4 voltage" | |
| depends on AXP221_POWER | |
| default 0 | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 dldo4 at, set to 0 to | |
| disable dldo4. | |
| config AXP221_ALDO1_VOLT | |
| int "axp221 aldo1 voltage" | |
| depends on AXP221_POWER | |
| default 0 | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 aldo1 at, set to 0 to | |
| disable aldo1. On sun6i (A31) boards which have a wifi module this is | |
| often used to power the wifi module. | |
| config AXP221_ALDO2_VOLT | |
| int "axp221 aldo2 voltage" | |
| depends on AXP221_POWER | |
| default 0 if MACH_SUN6I | |
| default 2500 if MACH_SUN8I | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 aldo2 at, set to 0 to | |
| disable aldo2. On sun6i (A31) boards this is typically unused and | |
| should be disabled, if it is used for LPDDR2 it should be set to 1.8V. | |
| On sun8i (A23) this is typically connected to VDD-DLL and must be set | |
| to 2.5V. | |
| config AXP221_ALDO3_VOLT | |
| int "axp221 aldo3 voltage" | |
| depends on AXP221_POWER | |
| default 3000 | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 aldo3 at, set to 0 to | |
| disable aldo3. This is typically connected to VCC-PLL and AVCC and | |
| must be set to 3V. | |
| config AXP221_ELDO3_VOLT | |
| int "axp221 eldo3 voltage" | |
| depends on AXP221_POWER | |
| default 0 | |
| ---help--- | |
| Set the voltage (mV) to program the axp221 eldo3 at, set to 0 to | |
| disable eldo3. On some A31(s) tablets it might be used to supply | |
| 1.2V for the SSD2828 chip (converter of parallel LCD interface | |
| into MIPI DSI). |