blob: 304a12bea9cef3d3bb27f980167fcb624b0649b6 [file] [log] [blame]
/*
* (C) Copyright 2001
* Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
/*************************************************************************
* (c) 2004 esd gmbh Hannover
*
*
* from db64360.h file
* by Reinhard Arlt reinhard.arlt@esd-electronics.com
*
************************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/* This define must be before the core.h include */
#define CONFIG_CPCI750 1 /* this is an CPCI750 board */
#ifndef __ASSEMBLY__
#include <../board/Marvell/include/core.h>
#endif
/*-----------------------------------------------------*/
#include "../board/esd/cpci750/local.h"
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_750FX /* we have a 750FX (override local.h) */
#define CONFIG_CPCI750 1 /* this is an CPCI750 board */
#define CONFIG_SYS_TEXT_BASE 0xfff00000
#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600 */
#define CONFIG_MV64360_ECC /* enable ECC support */
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R
#define CONFIG_BOARD_PRE_INIT
#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_SYS_BOARD_NAME "CPCI750"
#define CONFIG_IDENT_STRING "Marvell 64360 + IBM750FX"
/*#define CONFIG_SYS_HUSH_PARSER*/
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/* Define which ETH port will be used for connecting the network */
#define CONFIG_SYS_ETH_PORT ETH_0
/*
* The following defines let you select what serial you want to use
* for your console driver.
*
* what to do:
* to use the DUART, undef CONFIG_MPSC. If you have hacked a serial
* cable onto the second DUART channel, change the CONFIG_SYS_DUART port from 1
* to 0 below.
*
* to use the MPSC, #define CONFIG_MPSC. If you have wired up another
* mpsc channel, change CONFIG_MPSC_PORT to the desired value.
*/
#define CONFIG_MPSC
#define CONFIG_MPSC_PORT 0
/* to change the default ethernet port, use this define (options: 0, 1, 2) */
#define MV_ETH_DEVS 1
#define CONFIG_ETHER_PORT 0
#undef CONFIG_ETHER_PORT_MII /* use RMII */
#define CONFIG_BOOTDELAY 5 /* autoboot disabled */
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
#define CONFIG_ZERO_BOOTDELAY_CHECK
#undef CONFIG_BOOTARGS
/* -----------------------------------------------------------------------------
* New bootcommands for Marvell CPCI750 c 2002 Ingo Assmus
*/
#define CONFIG_IPADDR "192.168.0.185"
#define CONFIG_SERIAL "AA000001"
#define CONFIG_SERVERIP "10.0.0.79"
#define CONFIG_ROOTPATH "/export/nfs_cpci750/%s"
#define CONFIG_TESTDRAMDATA y
#define CONFIG_TESTDRAMADDRESS n
#define CONFIG_TESETDRAMWALK n
/* ----------------------------------------------------------------------------- */
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_ALTIVEC /* undef to disable */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_I2C
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_PCI
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DATE
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_EXT2
#define CONFIG_DOS_PARTITION
#define CONFIG_USE_CPCIDVI
#ifdef CONFIG_USE_CPCIDVI
#define CONFIG_VIDEO
#define CONFIG_VIDEO_CT69000
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VIDEO_LOGO
#define CONFIG_I8042_KBD
#define CONFIG_SYS_ISA_IO 0
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed default */
#define CONFIG_PRAM 0
#define CONFIG_SYS_GT_DUAL_CPU /* also for JTAG even with one cpu */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
/*#define CONFIG_SYS_MEMTEST_START 0x00400000*/ /* memtest works on */
/*#define CONFIG_SYS_MEMTEST_END 0x00C00000*/ /* 4 ... 12 MB in DRAM */
/*#define CONFIG_SYS_MEMTEST_END 0x07c00000*/ /* 4 ... 124 MB in DRAM */
/*
#define CONFIG_SYS_DRAM_TEST
* DRAM tests
* CONFIG_SYS_DRAM_TEST - enables the following tests.
*
* CONFIG_SYS_DRAM_TEST_DATA - Enables test for shorted or open data lines
* Environment variable 'test_dram_data' must be
* set to 'y'.
* CONFIG_SYS_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
* addressable. Environment variable
* 'test_dram_address' must be set to 'y'.
* CONFIG_SYS_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
* This test takes about 6 minutes to test 64 MB.
* Environment variable 'test_dram_walk' must be
* set to 'y'.
*/
#define CONFIG_SYS_DRAM_TEST
#if defined(CONFIG_SYS_DRAM_TEST)
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
/*#define CONFIG_SYS_MEMTEST_END 0x00C00000*/ /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */
#define CONFIG_SYS_DRAM_TEST_DATA
#define CONFIG_SYS_DRAM_TEST_ADDRESS
#define CONFIG_SYS_DRAM_TEST_WALK
#endif /* CONFIG_SYS_DRAM_TEST */
#define CONFIG_DISPLAY_MEMMAP /* at the end of the bootprocess show the memory map */
#undef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT /* show SPD content during boot */
#define CONFIG_SYS_LOAD_ADDR 0x00300000 /* default load address */
#define CONFIG_SYS_BUS_CLK 133000000 /* 133 MHz (CPU = 5*Bus = 666MHz) */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CONFIG_SYS_TCLK 133000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area
*/
/*
* When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS
* To an unused memory region. The stack will remain in cache until RAM
* is initialized
*/
#undef CONFIG_SYS_INIT_RAM_LOCK
/* #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000*/ /* unused memory region */
/* #define CONFIG_SYS_INIT_RAM_ADDR 0xfba00000*/ /* unused memory region */
#define CONFIG_SYS_INIT_RAM_ADDR 0xf1080000 /* unused memory region */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define RELOCATE_INTERNAL_RAM_ADDR
#ifdef RELOCATE_INTERNAL_RAM_ADDR
/*#define CONFIG_SYS_INTERNAL_RAM_ADDR 0xfba00000*/
#define CONFIG_SYS_INTERNAL_RAM_ADDR 0xf1080000
#endif
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* Dummies for BAT 4-7 */
#define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* each 256 MByte */
#define CONFIG_SYS_SDRAM2_BASE 0x20000000
#define CONFIG_SYS_SDRAM3_BASE 0x30000000
#define CONFIG_SYS_SDRAM4_BASE 0x40000000
#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MONITOR_BASE 0xfff00000
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 256 kB for malloc */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of flash banks */
#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */
#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* size of flash bank */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
CONFIG_SYS_FLASH_BASE + 1*CONFIG_SYS_FLASH_INCREMENT, \
CONFIG_SYS_FLASH_BASE + 2*CONFIG_SYS_FLASH_INCREMENT, \
CONFIG_SYS_FLASH_BASE + 3*CONFIG_SYS_FLASH_INCREMENT }
#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* show if bank is empty */
/* areas to map different things with the GT in physical space */
#define CONFIG_SYS_DRAM_BANKS 4
/* What to put in the bats. */
#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000
/* Peripheral Device section */
/*******************************************************/
/* We have on the cpci750 Board : */
/* GT-Chipset Register Area */
/* GT-Chipset internal SRAM 256k */
/* SRAM on external device module */
/* Real time clock on external device module */
/* dobble UART on external device module */
/* Data flash on external device module */
/* Boot flash on external device module */
/*******************************************************/
#define CONFIG_SYS_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */
#define CONFIG_SYS_CPCI750_RESET_ADDR 0x14000000 /* After power on Reset the CPCI750 is here */
#undef MARVEL_STANDARD_CFG
#ifndef MARVEL_STANDARD_CFG
/*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
#define CONFIG_SYS_GT_REGS 0xf1000000 /* GT Registers will be mapped here */
/*#define CONFIG_SYS_DEV_BASE 0xfc000000*/ /* GT Devices CS start here */
#define CONFIG_SYS_INT_SRAM_BASE 0xf1080000 /* GT offers 256k internal fast SRAM */
#define CONFIG_SYS_BOOT_SPACE 0xff000000 /* BOOT_CS0 flash 0 */
#define CONFIG_SYS_DEV0_SPACE 0xfc000000 /* DEV_CS0 flash 1 */
#define CONFIG_SYS_DEV1_SPACE 0xfd000000 /* DEV_CS1 flash 2 */
#define CONFIG_SYS_DEV2_SPACE 0xfe000000 /* DEV_CS2 flash 3 */
#define CONFIG_SYS_DEV3_SPACE 0xf0000000 /* DEV_CS3 nvram/can */
#define CONFIG_SYS_BOOT_SIZE _16M /* cpci750 flash 0 */
#define CONFIG_SYS_DEV0_SIZE _16M /* cpci750 flash 1 */
#define CONFIG_SYS_DEV1_SIZE _16M /* cpci750 flash 2 */
#define CONFIG_SYS_DEV2_SIZE _16M /* cpci750 flash 3 */
#define CONFIG_SYS_DEV3_SIZE _16M /* cpci750 nvram/can */
/*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++*/
#endif
/* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected by device width */
#define CONFIG_SYS_DEV0_PAR 0x8FDFFFFF /* 16 bit flash */
#define CONFIG_SYS_DEV1_PAR 0x8FDFFFFF /* 16 bit flash */
#define CONFIG_SYS_DEV2_PAR 0x8FDFFFFF /* 16 bit flash */
#define CONFIG_SYS_DEV3_PAR 0x8FCFFFFF /* nvram/can */
#define CONFIG_SYS_BOOT_PAR 0x8FDFFFFF /* 16 bit flash */
/* c 4 a 8 2 4 1 c */
/* 33 22|2222|22 22|111 1|11 11|1 1 | | */
/* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */
/* 11|00|0100|10 10|100|0 00|10 0|100 0|001 1|100 */
/* 3| 0|.... ..| 2| 4 | 0 | 4 | 8 | 3 | 4 */
/* MPP Control MV64360 Appendix P P. 632*/
#define CONFIG_SYS_MPP_CONTROL_0 0x00002222 /* */
#define CONFIG_SYS_MPP_CONTROL_1 0x11110000 /* */
#define CONFIG_SYS_MPP_CONTROL_2 0x11111111 /* */
#define CONFIG_SYS_MPP_CONTROL_3 0x00001111 /* */
/* #define CONFIG_SYS_SERIAL_PORT_MUX 0x00000102*/ /* */
#define CONFIG_SYS_GPP_LEVEL_CONTROL 0xffffffff /* 1111 1111 1111 1111 1111 1111 1111 1111*/
/* setup new config_value for MV64360 DDR-RAM To_do !! */
/*# define CONFIG_SYS_SDRAM_CONFIG 0xd8e18200*/ /* 0x448 */
/*# define CONFIG_SYS_SDRAM_CONFIG 0xd8e14400*/ /* 0x1400 */
/* GB has high prio.
idma has low prio
MPSC has low prio
pci has low prio 1 and 2
cpu has high prio
Data DQS pins == eight (DQS[7:0] foe x8 and x16 devices
ECC disable
non registered DRAM */
/* 31:26 25:22 21:20 19 18 17 16 */
/* 100001 0000 010 0 0 0 0 */
/* refresh_count=0x400
phisical interleaving disable
virtual interleaving enable */
/* 15 14 13:0 */
/* 0 1 0x400 */
# define CONFIG_SYS_SDRAM_CONFIG 0x58200400 /* 0x1400 copied from Dink32 bzw. VxWorks*/
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show devices on bus */
/* PCI MEMORY MAP section */
#define CONFIG_SYS_PCI0_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI0_MEM_SIZE _128M
#define CONFIG_SYS_PCI1_MEM_BASE 0x88000000
#define CONFIG_SYS_PCI1_MEM_SIZE _128M
#define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE)
#define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE)
/* PCI I/O MAP section */
#define CONFIG_SYS_PCI0_IO_BASE 0xfa000000
#define CONFIG_SYS_PCI0_IO_SIZE _16M
#define CONFIG_SYS_PCI1_IO_BASE 0xfb000000
#define CONFIG_SYS_PCI1_IO_SIZE _16M
#define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE)
#define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000
#define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE)
#define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS (CONFIG_SYS_PCI0_IO_BASE)
#if defined (CONFIG_750CX)
#define CONFIG_SYS_PCI_IDSEL 0x0
#else
#define CONFIG_SYS_PCI_IDSEL 0x30
#endif
/*-----------------------------------------------------------------------
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET /* no reset for ide supported */
#define CONFIG_IDE_PREINIT /* check for units */
#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 1 IDE busses */
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 1 drives per IDE bus */
#define CONFIG_SYS_ATA_BASE_ADDR 0
#define CONFIG_SYS_ATA_IDE0_OFFSET 0
#define CONFIG_SYS_ATA_IDE1_OFFSET 0
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
#ifndef __ASSEMBLY__
int ata_device(int dev);
#endif
#define ATA_DEVICE(dev) ata_device(dev)
#define CONFIG_ATAPI 1
/*----------------------------------------------------------------------
* Initial BAT mappings
*/
/* NOTES:
* 1) GUARDED and WRITE_THRU not allowed in IBATS
* 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
*/
/* SDRAM */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* init ram */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* PCI0, PCI1 in one BAT */
#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS
#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* GT regs, bootrom, all the devices, PCI I/O */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/*
* 750FX IBAT and DBAT pairs (To_do: define regins for I(D)BAT4 - I(D)BAT7)
* IBAT4 and DBAT4
* FIXME: ingo disable BATs for Linux Kernel
*/
/* #undef SETUP_HIGH_BATS_FX750 */ /* don't initialize BATS 4-7 */
#define SETUP_HIGH_BATS_FX750 /* initialize BATS 4-7 */
#ifdef SETUP_HIGH_BATS_FX750
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* IBAT5 and DBAT5 */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_SDRAM2_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_SDRAM2_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_SDRAM2_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
/* IBAT6 and DBAT6 */
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_SDRAM3_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT6U (CONFIG_SYS_SDRAM3_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT6L (CONFIG_SYS_SDRAM3_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
/* IBAT7 and DBAT7 */
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#else /* set em out of range for Linux !!!!!!!!!!! */
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* IBAT5 and DBAT5 */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT4U
/* IBAT6 and DBAT6 */
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT6U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT6L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT4U
/* IBAT7 and DBAT7 */
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM4_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT7L (CONFIG_SYS_SDRAM4_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT4U
#endif
/* FIXME: ingo end: disable BATs for Linux Kernel */
/* I2C addresses for the two DIMM SPD chips */
#define DIMM0_I2C_ADDR 0x51
#define DIMM1_I2C_ADDR 0x52
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_BOOT_FLASH_WIDTH 2 /* 16 bit */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_LOCK_TOUT 500 /* Timeout for Flash Lock (in ms) */
#if 0
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_ADDR 0xFFF78000 /* Marvell 8-Bit Bootflash last sector */
/* #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_MONITOR_LEN-CONFIG_ENV_SECT_SIZE) */
#endif
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x050
#define CONFIG_ENV_OFFSET 0x200 /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x600 /* 2048 bytes may be used for env vars*/
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-0x40)
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* L2CR setup -- make sure this is right for your board!
* look in include/mpc74xx.h for the defines used here
*/
/*#define CONFIG_SYS_L2*/
#undef CONFIG_SYS_L2
/* #ifdef CONFIG_750CX*/
#if defined (CONFIG_750CX) || defined (CONFIG_750FX)
#define L2_INIT 0
#else
#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
#endif
#define L2_ENABLE (L2_INIT | L2CR_L2E)
#define CONFIG_SYS_BOARD_ASM_INIT 1
#define CPCI750_SLAVE_TEST (((in8(0xf0300000) & 0x80) == 0) ? 0 : 1)
#define CPCI750_ECC_TEST (((in8(0xf0300000) & 0x02) == 0) ? 1 : 0)
#define CONFIG_SYS_PLD_VER 0xf0e00000
#define CONFIG_OF_LIBFDT 1
#endif /* __CONFIG_H */