blob: 0ffbd41b4996a69a14c1f8ff155021690b50970c [file] [log] [blame]
/*
* (C) Copyright 2002 ELTEC Elektronik AG
* Frank Gottschling <fgottschling@eltec.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define GTREGREAD(x) 0xffffffff /* needed for debug */
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
/* these hardware addresses are pretty bogus, please change them to
suit your needs */
/* first ethernet */
#define CONFIG_ETHADDR 00:00:5b:ee:de:ad
#define CONFIG_IPADDR 192.168.0.105
#define CONFIG_SERVERIP 192.168.0.100
#define CONFIG_ELPPC 1 /* this is an BAB740/BAB750 board */
#define CONFIG_BAUDRATE 9600 /* console baudrate */
#undef CONFIG_WATCHDOG
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_ZERO_BOOTDELAY_CHECK
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp 1000000; " \
"setenv bootargs root=ramfs console=ttyS00,9600 " \
"ip=${ipaddr}:${serverip}:${rootpath}:${gatewayip}:" \
"${netmask}:${hostname}:eth0:none; " \
"bootm"
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PCI
#define CONFIG_CMD_JFFS2
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
/*
* choose between COM1 and COM2 as serial console
*/
#define CONFIG_CONS_INDEX 1
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 64 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CONFIG_SYS_BOARD_ASM_INIT
#define CONFIG_MISC_INIT_R
/*
* Address mapping scheme for the MPC107 mem controller is mapping B (CHRP)
*/
#undef CONFIG_SYS_ADDRESS_MAP_A
#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
#define CONFIG_SYS_PCI_MEMORY_SIZE 0x40000000
#define CONFIG_SYS_PCI_MEM_BUS 0x80000000
#define CONFIG_SYS_PCI_MEM_PHYS 0x80000000
#define CONFIG_SYS_PCI_MEM_SIZE 0x7d000000
#define CONFIG_SYS_ISA_MEM_BUS 0x00000000
#define CONFIG_SYS_ISA_MEM_PHYS 0xfd000000
#define CONFIG_SYS_ISA_MEM_SIZE 0x01000000
#define CONFIG_SYS_PCI_IO_BUS 0x00800000
#define CONFIG_SYS_PCI_IO_PHYS 0xfe800000
#define CONFIG_SYS_PCI_IO_SIZE 0x00400000
#define CONFIG_SYS_ISA_IO_BUS 0x00000000
#define CONFIG_SYS_ISA_IO_PHYS 0xfe000000
#define CONFIG_SYS_ISA_IO_SIZE 0x00800000
/* driver defines FDC,IDE,... */
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_ISA_IO_PHYS
#define CONFIG_SYS_ISA_IO CONFIG_SYS_ISA_IO_PHYS
#define CONFIG_SYS_60X_PCI_IO_OFFSET CONFIG_SYS_ISA_IO_PHYS
/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_USR_LED_BASE 0x78000000
#define CONFIG_SYS_NVRAM_BASE 0xff000000
#define CONFIG_SYS_UART_BASE 0xff400000
#define CONFIG_SYS_FLASH_BASE 0xfff00000
#define MPC107_EUMB_ADDR 0xfce00000
#define MPC107_EUMB_PI 0xfce41090
#define MPC107_EUMB_GCR 0xfce41020
#define MPC107_EUMB_IACKR 0xfce600a0
#define MPC107_I2C_ADDR 0xfce03000
/*
* Definitions for initial stack pointer and data area
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x00fd0000 /* above the memtest region */
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Flash mapping/organization on the MPC10x.
*/
#define FLASH_BASE0_PRELIM 0xff800000
#define FLASH_BASE1_PRELIM 0xffc00000
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=elppc-0,nor1=elppc-1"
#define MTDPARTS_DEFAULT "mtdparts=elppc-0:-(jffs2),elppc-1:-(user)"
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN 0x20000 /* Reserve 128 kB for malloc() */
#undef CONFIG_SYS_MEMTEST
/*
* Environment settings
*/
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#define CONFIG_SYS_NVRAM_SIZE 0x800 /* NVRAM size (2kB) */
#define CONFIG_ENV_SIZE 0x400 /* Size of Environment vars (1kB) */
#define CONFIG_ENV_ADDR 0x0
#define CONFIG_ENV_MAP_ADRS 0xff000000
#define CONFIG_SYS_NV_SROM_COPY_ADDR (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_SYS_NVRAM_ACCESS_ROUTINE /* only byte accsess alowed */
#define CONFIG_SYS_SROM_SIZE 0x100 /* shadow of revision info is in nvram */
/*
* Serial devices
*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK 24000000
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_UART_BASE + 0)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_UART_BASE + 8)
/*
* PCI stuff
*/
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_PNP /* pci plug-and-play */
#define CONFIG_PCI_HOST PCI_HOST_AUTO
#undef CONFIG_PCI_SCAN_SHOW
/*
* Optional Video console (graphic: SMI LynxEM)
*/
#define CONFIG_VIDEO
#define CONFIG_CFB_CONSOLE
#define VIDEO_KBD_INIT_FCT (simple_strtol (getenv("console"), NULL, 10))
#define VIDEO_TSTC_FCT serial_tstc
#define VIDEO_GETC_FCT serial_getc
#define CONFIG_VIDEO_SMI_LYNXEM
#define CONFIG_VIDEO_LOGO
#define CONFIG_CONSOLE_EXTRA_INFO
/*
* Initial BATs
*/
#if 1
#define CONFIG_SYS_IBAT0L 0
#define CONFIG_SYS_IBAT0U 0
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_IBAT1L 0
#define CONFIG_SYS_IBAT1U 0
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_IBAT2L 0
#define CONFIG_SYS_IBAT2U 0
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_IBAT3L 0
#define CONFIG_SYS_IBAT3U 0
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#else
/* SDRAM */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_RW)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT1U
/* address range for flashes */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* ISA IO space */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_ISA_IO | BATL_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* ISA memory space */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#endif
/*
* Speed settings are board specific
*/
#define CONFIG_SYS_BUS_CLK 100000000
#define CONFIG_SYS_CPU_CLK 400000000
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* L2CR setup -- make sure this is right for your board!
* look in include/74xx_7xx.h for the defines used here
*/
#define CONFIG_SYS_L2
#if 1
#define L2_INIT 0 /* cpu 750 CXe*/
#else
#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
#endif
#define L2_ENABLE (L2_INIT | L2CR_L2E)
#define CONFIG_EEPRO100
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_EEPRO100_SROM_WRITE
#endif /* __CONFIG_H */