blob: 74f44df68238194973693131aad72c8260ff0dca [file] [log] [blame]
/*
* A collection of structures, addresses, and values associated with
* the Motorola 860T MBX board.
* Copied from the FADS stuff, which was originally copied from the MBX stuff!
* Magnus Damm added defines for 8xxrom and extended bd_info.
* Helmut Buchsbaum added bitvalues for BCSRx
* Rob Taylor coverted it back to MBX
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
*/
/* ------------------------------------------------------------------------- */
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#include <mpc8xx_irq.h>
#define CONFIG_MPC860 1
#define CONFIG_MPC860T 1
#define CONFIG_MBX 1
#define CONFIG_SYS_TEXT_BASE 0xfe000000
#define CONFIG_8xx_CPUCLOCK 40
#define CONFIG_8xx_BUSCLOCK (CONFIG_8xx_CPUCLOCK)
#define TARGET_SYSTEM_FREQUENCY 40
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#define CONFIG_BAUDRATE 9600
#define MPC8XX_FACT 10 /* Multiply by 10 */
#define MPC8XX_XIN 40000000 /* 50 MHz in */
#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#if 1
#define CONFIG_8xx_BOOTDELAY -1 /* autoboot disabled */
#define CONFIG_8xx_TFTP_MODE
#else
#define CONFIG_8xx_BOOTDELAY 5 /* autoboot after 5 seconds */
#undef CONFIG_8xx_TFTP_MODE
#endif
#define CONFIG_MISC_INIT_R
#define CONFIG_DRAM_SPEED (CONFIG_8xx_BUSCLOCK) /* MHz */
#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */
#define CONFIG_BOOTARGS " "
/*
* Miscellaneous configurable options
*/
#undef CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0800000 /* 4 ... 8 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CONFIG_SYS_IMMR 0xFFA00000
#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
#define CONFIG_SYS_NVRAM_BASE 0xFA000000 /* NVRAM */
#define CONFIG_SYS_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */
#define CONFIG_SYS_CSR_BASE 0xFA100000 /* Control/Status Registers */
#define CONFIG_SYS_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */
#define CONFIG_SYS_PCIMEM_OR 0xA0000108
#define CONFIG_SYS_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */
#define CONFIG_SYS_PCIBRIDGE_OR 0xFFFF0108
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_SIZE 0x2f00 /* Size of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */
#define CONFIG_SYS_INIT_VPD_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_VPD_OFFSET-8)
/*-----------------------------------------------------------------------
* Offset in DPMEM where we keep the VPD data
*/
#define CONFIG_SYS_DPRAMVPD (CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0x00000000
/*0xFE000000*/
#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_HWINFO_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
/*-----------------------------------------------------------------------
* NVRAM Configuration
*
* Note: the MBX is special because there is already a firmware on this
* board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
* access the NVRAM at the offset 0x1000.
*/
#define CONFIG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */
#define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE + 0x1000)
#define CONFIG_ENV_SIZE 0x1000
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit - leave PLL multiplication factor unchanged !
*/
#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL)
#define CONFIG_SYS_SCCR SCCR_TBS
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_DER 0
/* Because of the way the 860 starts up and assigns CS0 the
* entire address space, we have to set the memory controller
* differently. Normally, you write the option register
* first, and then enable the chip select by writing the
* base register. For CS0, you must write the base register
* first, followed by the option register.
*/
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
/* the other CS:s are determined by looking at parameters in BCSRx */
#define BCSR_ADDR ((uint) 0xFF010000)
#define BCSR_SIZE ((uint)(64 * 1024))
#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0xFF010000 /* FLASH bank #0 */
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM 0xFFF00000 /* OR addr mask */
/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM (0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
#define CONFIG_SYS_BR0_PRELIM (0xFE000000 | BR_V )
/* BCSRx - Board Control and Status Registers */
#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
#define CONFIG_SYS_OR1_PRELIM 0xFFC00000 | OR_ACS_DIV4
#define CONFIG_SYS_BR1_PRELIM (0x00000000 | BR_MS_UPMA | BR_V )
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 8 column SDRAM */
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
#define CONFIG_SYS_MAMR 0x13821000
/* values according to the manual */
#define PCMCIA_MEM_ADDR ((uint)0xff020000)
#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
#define BCSR0 ((uint) (BCSR_ADDR + 00))
#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
/* FADS bitvalues by Helmut Buchsbaum
* see MPC8xxADS User's Manual for a proper description
* of the following structures
*/
#define BCSR0_ERB ((uint)0x80000000)
#define BCSR0_IP ((uint)0x40000000)
#define BCSR0_BDIS ((uint)0x10000000)
#define BCSR0_BPS_MASK ((uint)0x0C000000)
#define BCSR0_ISB_MASK ((uint)0x01800000)
#define BCSR0_DBGC_MASK ((uint)0x00600000)
#define BCSR0_DBPC_MASK ((uint)0x00180000)
#define BCSR0_EBDF_MASK ((uint)0x00060000)
#define BCSR1_FLASH_EN ((uint)0x80000000)
#define BCSR1_DRAM_EN ((uint)0x40000000)
#define BCSR1_ETHEN ((uint)0x20000000)
#define BCSR1_IRDEN ((uint)0x10000000)
#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
#define BCSR1_BCSR_EN ((uint)0x02000000)
#define BCSR1_RS232EN_1 ((uint)0x01000000)
#define BCSR1_PCCEN ((uint)0x00800000)
#define BCSR1_PCCVCC0 ((uint)0x00400000)
#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
#define BCSR1_RS232EN_2 ((uint)0x00040000)
#define BCSR1_SDRAM_EN ((uint)0x00020000)
#define BCSR1_PCCVCC1 ((uint)0x00010000)
#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
#define BCSR2_DRAM_PD_SHIFT (23)
#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
#define BCSR3_DBID_MASK ((ushort)0x3800)
#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
#define BCSR3_BREVNR0 ((ushort)0x0080)
#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
#define BCSR3_BREVN1 ((ushort)0x0008)
#define BCSR3_BREVN2_MASK ((ushort)0x0003)
#define BCSR4_ETHLOOP ((uint)0x80000000)
#define BCSR4_TFPLDL ((uint)0x40000000)
#define BCSR4_TPSQEL ((uint)0x20000000)
#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
#ifdef CONFIG_MPC823
#define BCSR4_USB_EN ((uint)0x08000000)
#endif /* CONFIG_MPC823 */
#ifdef CONFIG_MPC860SAR
#define BCSR4_UTOPIA_EN ((uint)0x08000000)
#endif /* CONFIG_MPC860SAR */
#ifdef CONFIG_MPC860T
#define BCSR4_FETH_EN ((uint)0x08000000)
#endif /* CONFIG_MPC860T */
#define BCSR4_USB_SPEED ((uint)0x04000000)
#define BCSR4_VCCO ((uint)0x02000000)
#define BCSR4_VIDEO_ON ((uint)0x00800000)
#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
#define BCSR4_VIDEO_RST ((uint)0x00200000)
#define BCSR4_MODEM_EN ((uint)0x00100000)
#define BCSR4_DATA_VOICE ((uint)0x00080000)
#define CONFIG_DRAM_40MHZ 1
#ifdef CONFIG_MPC860T
/* Interrupt level assignments.
*/
#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
#endif /* CONFIG_MPC860T */
/* We don't use the 8259.
*/
#define NR_8259_INTS 0
#define CONFIG_CMD_NET
/*
* MPC8xx CPM Options
*/
#define CONFIG_SCC_ENET 1
#define CONFIG_SCC1_ENET 1
#define CONFIG_FEC_ENET 1
#undef CONFIG_CPM_IIC
#undef CONFIG_UCODE_PATCH
#define CONFIG_DISK_SPINUP_TIME 1000000
/* PCMCIA configuration */
#define PCMCIA_MAX_SLOTS 2
#ifdef CONFIG_MPC860
#define PCMCIA_SLOT_A 1
#endif
#endif /* __CONFIG_H */