blob: cc88ac1618a3c4b7bed4806120274cb3466d3419 [file] [log] [blame]
/*
* (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2010
* Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
#define CONFIG_A4M072 1 /* ... on A4M072 board */
#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
#define CONFIG_SYS_TEXT_BASE 0xFE000000
#define CONFIG_MISC_INIT_R
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/* define to enable silent console */
#define CONFIG_SILENT_CONSOLE
#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
/*
* PCI Mapping:
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
*/
#define CONFIG_PCI
#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_MEM_SIZE 0x10000000
#define CONFIG_PCI_IO_BUS 0x50000000
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
#endif
#define CONFIG_SYS_XLB_PIPELINING 1
#undef CONFIG_EEPRO100
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
/* USB */
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_USB
#define CONFIG_CMD_MII
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_DISPLAY
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low with 32 MB Flash */
#define CONFIG_SYS_LOWBOOT 1
#define CONFIG_SYS_LOWBOOT32 1
#endif
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
#define CONFIG_SYS_AUTOLOAD "n"
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "asdfg"
#undef CONFIG_BOOTARGS
#define CONFIG_PREBOOT "run try_update"
#define CONFIG_EXTRA_ENV_SETTINGS \
"bk=run add_mtd ; run add_consolespec ; bootm 200000\0" \
"cf1=diskboot 200000 0:1\0" \
"bootcmd_cf1=run bcf1\0" \
"bcf=setenv bootargs root=/dev/hda3\0" \
"bootcmd_nfs=run bnfs\0" \
"norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs "\
"panic=1\0" \
"bootcmd_nor=cp.b ${kernel_addr} 200000 100000;" \
"run norargs addip; run bk\0" \
"bnfs=nfs 200000 ${rootpath}/boot/uImage;" \
"run nfsargs addip ; run bk\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"try_update=usb start;sleep 2;usb start;sleep 1;" \
"fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;" \
"source 2F0000\0" \
"env_addr=FE060000\0" \
"kernel_addr=FE100000\0" \
"rootfs_addr=FE200000\0" \
"add_mtd=setenv bootargs ${bootargs} mtdparts=" \
"phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0" \
"bcf1=run cf1; run bcf; run addip; run bk\0" \
"add_consolespec=setenv bootargs ${bootargs} " \
"console=/dev/null quiet\0" \
"addip=if test -n ${ethaddr};" \
"then if test -n ${ipaddr};" \
"then setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:"\
"${netmask}:${hostname}:${netdev}:off;" \
"fi;" \
"else;" \
"setenv bootargs ${bootargs} no_ethaddr;" \
"fi\0" \
"hostname=CPUP0\0" \
"ethaddr=00:00:00:00:00:00\0" \
"netdev=eth0\0" \
"bootcmd=run bootcmd_nor\0" \
""
/*
* IPB Bus clocking configuration.
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_EEPROM_WREN 1
#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4
/*
* Flash configuration
*/
#define CONFIG_SYS_FLASH_BASE 0xFE000000
#define CONFIG_SYS_FLASH_SIZE 0x02000000
#if !defined(CONFIG_SYS_LOWBOOT)
#error "CONFIG_SYS_LOWBOOT not defined?"
#else /* CONFIG_SYS_LOWBOOT */
#if defined(CONFIG_SYS_LOWBOOT32)
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
#endif
#endif /* CONFIG_SYS_LOWBOOT */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_CS0_START}
#define CONFIG_SYS_FLASH_BANKS_SIZES {CONFIG_SYS_CS0_SIZE}
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SIZE 0x10000
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_ENV_OVERWRITE 1
/*
* Memory map
*/
#define CONFIG_SYS_MBAR 0xF0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_MPC5xxx_FEC_MII100
/*
* Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
*/
/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR 0x1f
#define CONFIG_PHY_TYPE 0x79c874 /* AMD Phy Controller */
/*
* GPIO configuration
*/
#define CONFIG_SYS_GPS_PORT_CONFIG 0x18000004
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Various low-level settings
*/
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL HID0_ICE
/* Flash at CSBoot, CS0 */
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_BOOTCS_CFG 0x0002DD00
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
/* External SRAM at CS1 */
#define CONFIG_SYS_CS1_START 0x62000000
#define CONFIG_SYS_CS1_SIZE 0x00400000
#define CONFIG_SYS_CS1_CFG 0x00009930
#define CONFIG_SYS_SRAM_BASE CONFIG_SYS_CS1_START
#define CONFIG_SYS_SRAM_SIZE CONFIG_SYS_CS1_SIZE
/* LED display at CS7 */
#define CONFIG_SYS_CS7_START 0x6a000000
#define CONFIG_SYS_CS7_SIZE (64*1024)
#define CONFIG_SYS_CS7_CFG 0x0000bf30
#define CONFIG_SYS_CS_BURST 0x00000000
#define CONFIG_SYS_CS_DEADCYCLE 0x33333003
#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*-----------------------------------------------------------------------
* USB stuff
*-----------------------------------------------------------------------
*/
#define CONFIG_USB_CLOCK 0x0001BBBB
#define CONFIG_USB_CONFIG 0x00001000 /* 0x4000 for SE mode */
/*-----------------------------------------------------------------------
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_PREINIT
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
#define CONFIG_SYS_ATA_STRIDE 4
#define CONFIG_ATAPI 1
/*-----------------------------------------------------------------------
* Open firmware flat tree support
*-----------------------------------------------------------------------
*/
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define OF_CPU "PowerPC,5200@0"
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
/* Support for the 7-segment display */
#define CONFIG_SYS_DISP_CHR_RAM CONFIG_SYS_CS7_START
#define CONFIG_SHOW_ACTIVITY /* used for display realization */
#define CONFIG_SHOW_BOOT_PROGRESS
#endif /* __CONFIG_H */