blob: c98b687c09c86a75d4e2c0c0a272998d2b8e2b9e [file] [log] [blame]
/*
* (C) Copyright 2000-2010
* Murray Jensen <Murray.Jensen@cmst.csiro.au>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* Config header file for Cogent platform using an MPC8xx CPU module
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC860 1 /* This is an MPC860 CPU */
#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */
#define CONFIG_SYS_TEXT_BASE 0xfff00000
#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
#define CONFIG_MISC_INIT_R /* Use misc_init_r() */
/* Cogent Modular Architecture options */
#define CONFIG_CMA286_60_OLD 1 /* ...on an old CMA286-60 CPU module */
#define CONFIG_CMA102 1 /* ...on a CMA102 motherboard */
#define CONFIG_CMA302 1 /* ...with a CMA302 flash I/O module */
/* serial console configuration */
#undef CONFIG_8xx_CONS_SMC1
#undef CONFIG_8xx_CONS_SMC2
#define CONFIG_8xx_CONS_NONE /* not on 8xx serial ports (eg on cogent m/b) */
#if defined(CONFIG_CMA286_60_OLD)
#define CONFIG_8xx_GCLK_FREQ 33333000 /* define if cant use get_gclk_freq */
#endif
#define CONFIG_BAUDRATE 230400
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_KGDB
#define CONFIG_CMD_I2C
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
#define CONFIG_BOOTCOMMAND "bootm 04080000 04200000" /* autoboot command*/
#define CONFIG_BOOTARGS "root=/dev/ram rw"
#if defined(CONFIG_CMD_KGDB)
#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
#undef CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
#define CONFIG_KGDB_NONE /* define if kgdb on something else */
#define CONFIG_KGDB_INDEX 2 /* which SMC/SCC channel for kgdb */
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CONFIG_SYS_ALLOC_DPRAM
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Low Level Cogent settings
* if CONFIG_SYS_CMA_CONS_SERIAL is defined, make sure the 8xx CPM serial is not.
* also, make sure CONFIG_CONS_INDEX is still defined - the index will be
* 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B
* (second 2 for CMA120 only)
*/
#define CONFIG_SYS_CMA_MB_BASE 0x00000000 /* base of m/b address space */
#include <configs/cogent_common.h>
#define CONFIG_SYS_CMA_CONS_SERIAL /* use Cogent motherboard serial for console */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_CMA_LCD_HEARTBEAT /* define for sec rotator in lcd corner */
#define CONFIG_SHOW_ACTIVITY
#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH)
/*
* flash exists on the motherboard
* set these four according to TOP dipsw:
* TOP on => ..._FLLOW_... (boot EPROM space is high so FLASH is low )
* TOP off => ..._FLHIGH_... (boot EPROM space is low so FLASH is high)
*/
#define CMA_MB_FLASH_EXEC_BASE CMA_MB_FLLOW_EXEC_BASE
#define CMA_MB_FLASH_EXEC_SIZE CMA_MB_FLLOW_EXEC_SIZE
#define CMA_MB_FLASH_RDWR_BASE CMA_MB_FLLOW_RDWR_BASE
#define CMA_MB_FLASH_RDWR_SIZE CMA_MB_FLLOW_RDWR_SIZE
#endif
#define CMA_MB_FLASH_BASE CMA_MB_FLASH_EXEC_BASE
#define CMA_MB_FLASH_SIZE CMA_MB_FLASH_EXEC_SIZE
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CONFIG_SYS_IMMR 0xFF000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE CMA_MB_RAM_BASE
#ifdef CONFIG_CMA302
#define CONFIG_SYS_FLASH_BASE CMA_MB_SLOT2_BASE /* cma302 in slot 2 */
#else
#define CONFIG_SYS_FLASH_BASE CMA_MB_FLASH_BASE /* flash on m/b */
#endif
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE /* Addr of Environment Sector */
#ifdef CONFIG_CMA302
#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
#define CONFIG_ENV_SECT_SIZE (512*1024) /* see README - env sect real size */
#else
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit - leave PLL multiplication factor unchanged !
*/
#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
/*#define CONFIG_SYS_DER 0x2002000F*/
#define CONFIG_SYS_DER 0
#if defined(CONFIG_CMA286_60_OLD)
/*
* Init Memory Controller:
*
* NOTE: although the names (CONFIG_SYS_xRn_PRELIM) suggest preliminary settings,
* they are actually the final settings for this cpu/board, because the
* flash and RAM are on the motherboard, accessed via the CMAbus, and the
* mappings are pretty much fixed.
*
* (the *_SIZE vars must be a power of 2)
*/
#define CONFIG_SYS_CMA_CS0_BASE CONFIG_SYS_TEXT_BASE /* EPROM */
#define CONFIG_SYS_CMA_CS0_SIZE (1 << 20)
#define CONFIG_SYS_CMA_CS1_BASE CMA_MB_RAM_BASE /* RAM + I/O SLOT 1 */
#define CONFIG_SYS_CMA_CS1_SIZE (64 << 20)
#define CONFIG_SYS_CMA_CS2_BASE CMA_MB_SLOT2_BASE /* I/O SLOTS 2 + 3 */
#define CONFIG_SYS_CMA_CS2_SIZE (64 << 20)
#define CONFIG_SYS_CMA_CS3_BASE CMA_MB_ROMLOW_BASE /* M/B I/O */
#define CONFIG_SYS_CMA_CS3_SIZE (32 << 20)
/*
* CS0 maps the EPROM on the cpu module
* Set it for 4 wait states, address CONFIG_SYS_MONITOR_BASE and size 1M
*
* Note: We must have already transferred control to the final location
* of the EPROM before these are used, because when BR0/OR0 are set, the
* mirror of the eprom at any other addresses will disappear.
*/
/* base address = CONFIG_SYS_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm */
#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_CMA_CS0_BASE&BR_BA_MSK)|BR_PS_16|BR_WP|BR_V)
/* mask size CONFIG_SYS_CMA_CS0_SIZE, CS time normal, burst inhibit, 4-wait states */
#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_CMA_CS0_SIZE-1)&OR_AM_MSK)|OR_BI|OR_SCY_4_CLK)
/*
* CS1 maps motherboard DRAM and motherboard I/O slot 1
* (each 32Mbyte in size)
*/
/* base address = CONFIG_SYS_CMA_CS1_BASE, 32-bit, no parity, r/w, gpcm */
#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_CMA_CS1_BASE&BR_BA_MSK)|BR_V)
/* mask size CONFIG_SYS_CMA_CS1_SIZE, CS time normal, burst ok, ext xfer ack */
#define CONFIG_SYS_OR1_PRELIM ((~(CONFIG_SYS_CMA_CS1_SIZE-1)&OR_AM_MSK)|OR_SETA)
/*
* CS2 maps motherboard I/O slots 2 and 3
* (each 32Mbyte in size)
*/
/* base address = CONFIG_SYS_CMA_CS2_BASE, 32-bit, no parity, r/w, gpcm */
#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_CMA_CS2_BASE&BR_BA_MSK)|BR_V)
/* mask size CONFIG_SYS_CMA_CS2_SIZE, CS time normal, burst ok, ext xfer ack */
#define CONFIG_SYS_OR2_PRELIM ((~(CONFIG_SYS_CMA_CS2_SIZE-1)&OR_AM_MSK)|OR_SETA)
/*
* CS3 maps motherboard I/O
* (32Mbyte in size)
*/
/* base address = CONFIG_SYS_CMA_CS3_BASE, 32-bit, no parity, r/w, gpcm */
#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_CMA_CS3_BASE&BR_BA_MSK)|BR_V)
/* mask size CONFIG_SYS_CMA_CS3_SIZE, CS time normal, burst inhibit, ext xfer ack */
#define CONFIG_SYS_OR3_PRELIM ((~(CONFIG_SYS_CMA_CS3_SIZE-1)&OR_AM_MSK)|OR_BI|OR_SETA)
#endif
#endif /* __CONFIG_H */